For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc host controller enters suspend state, the clocks are
disabled, but irqs are not. For some reason the irqchip emits
false interrupts, which causes system lock loop.
Debug log is:
...
sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
sunxi-mmc 1c11000.mmc: enabling the clock
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 AGND3R 14.6 GiB
mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
mmcblk1: p1
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
and so on...
This issue apears on eMMC cards, routed on MMC2 slot. The patch is
tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no obvious reasons to why mvsdio shouldn't be able to support
erase/trim/discard operations, hence let's set MMC_CAP_ERASE for it.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Instead of using a hardcoded timeout of 5 * HZ jiffies, let's respect the
command busy timeout provided by the mmc core. This make the used timeout
more reliable.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The highmem conversion caused a build error in some configurations:
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_transfer_data':
drivers/mmc/host/mxcmmc.c:622:10: error: implicit declaration of function 'kmap_atomic'; did you mean 'in_atomic'? [-Werror=implicit-function-declaration]
This includes the correct header file.
Fixes: b189e7589f ("mmc: mxcmmc: handle highmem pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added runtime-pm functions cause a harmless warning
when CONFIG_PM is disabled:
drivers/mmc/host/sunxi-mmc.c:1452:12: error: 'sunxi_mmc_runtime_suspend' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/sunxi-mmc.c:1435:12: error: 'sunxi_mmc_runtime_resume' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_resume(struct device *dev)
This marks them as __maybe_unused to shut up the warning.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I noticed below error msg with sdhci-pxav3 on some berlin platforms:
[.....] sdhci-pxav3 f7ab0000.sdhci failed to add host
It is due to getting related vmmc or vqmmc regulator returns
-EPROBE_DEFER. It doesn't matter at all but it's confusing.
>From another side, if driver probing fails and the error number isn't
-EPROBE_DEFER, the core will tell us something as below:
[.....] sdhci-pxav3: probe of f7ab0000.sdhci failed with error -EXX
So it's not necessary to emit error msg if sdhci_add_host() fails. And
some other sdhci host drivers also have this issue, let's fix them
together.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sg_copy_{from,to}_buffer to bounce buffer and kmap_atomic to map the
scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass the scatterlist on to the USB subsystem instead of expecting a
kernel virtual address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trigger the reset line of the mmc controller while probing, if available.
The reset should be optional for now, at least until all related DT nodes
have the reset property.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds extension to the dw_mmc driver for Mellanox BlueField
SoC. It updates the UHS_REG_EXT register to bring up the eMMC card on
this SoC.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A redundant return statement is removed from
tegra_sdhci_set_uhs_signaling(). The function returns void and the
return does not affect the control flow of the function.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using a fixed 3s timeout for commands with R1B responses,
convert to use the per request calculated busy timeout from the mmc core.
This is needed to cope with requests that requires longer timeout, for
example erase/discard commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Instead of having to return -EINVAL when requested to send SDIO specific
commands, let's set MMC_CAP2_NO_SDIO as it completely prevents them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
commit 8d20b2eae6 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_omap_enable_sdio_irq to set CTPL and CLKEXTFREE bits in
MMCHS_CON register required to detect asynchronous card interrupt
on DAT[1].
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.
The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.
Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.
Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
