This was accidentally removed when we defeatured the full 1588 Clock
support. We need to report the Rx descriptor timestamp value so that
applications built on top of the IES API can function properly.
Additionally, remove the FM10K_FLAG_RX_TS_ENABLED, as it is not used now
that 1588 functionality has been removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On packet RX, we perform a dma sync for cpu before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Partially revert commit 5e93cbadd3 ("fm10k: Reset mailbox global
interrupts", 2016-06-07)
The register bits related to this commit are now solely being handled by
the IES API. Recent changes in the IES API will allow an automatic
recovery from improper handling of these bits.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Multiple IES API resets can cause a race condition where the mailbox
interrupt request bits can be cleared before being handled. This can
leave certain mailbox messages from the PF to be untreated and the PF
will enter in some inactive state. If this situation occurs, the IES API
will initiate a mailbox version reset which, then, trigger a mailbox
state change. Once this mailbox transition occurs (from OPEN to CONNECT
state), a request for reset will be returned.
This ensures that PF will undergo a reset whenever IES API encounters an
unknown global mailbox interrupt event or whenever the IES API
terminates.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to ixgbe, when an interface is part of a namespace it is
possible that igb_close() may be called while __igb_shutdown() is
running which ends up in a double free WARN and/or a BUG in
free_msi_irqs().
Extend the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme() in __igb_shutdown() and check for
netif_device_present() to avoid calling igb_clear_interrupt_scheme() a
second time in igb_close().
Also extend the rtnl lock in igb_resume() to netif_device_attach().
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().
In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.
We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.
Reported-by: Anthony H Thai <ahthai@us.ibm.com>
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several people have reported firmware leaving the I210/I211 PHY's page
select register set to something other than the default of zero. This
causes the first accesses, PHY_IDx register reads, to access something
else, resulting in device probe failure:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
This problem began for them after a previous patch I submitted was
applied:
commit 2a3cdead8b
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 3 12:37:09 2015 -0600
igb: Remove GS40G specific defines/functions
I personally experienced this problem after attempting to PXE boot from
I210 devices using this firmware:
Intel(R) Boot Agent GE v1.5.78
Copyright (C) 1997-2014, Intel Corporation
Resetting the PHY before reading from it, ensures the page select
register is in its default state and doesn't make assumptions about
the PHY's register set before the PHY has been probed.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Chris Arges <carges@vectranetworks.com>
Cc: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Tested-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running as guest, under certain condition, it will oops as following.
writel() in igb_configure_tx_ring() results in oops, because hw->hw_addr
is NULL. While other register access won't oops kernel because they use
wr32/rd32 which have a defense against NULL pointer.
[ 141.225449] pcieport 0000:00:1c.0: AER: Multiple Uncorrected (Fatal)
error received: id=0101
[ 141.225523] igb 0000:01:00.1: PCIe Bus Error:
severity=Uncorrected (Fatal), type=Unaccessible,
id=0101(Unregistered Agent ID)
[ 141.299442] igb 0000:01:00.1: broadcast error_detected message
[ 141.300539] igb 0000:01:00.0 enp1s0f0: PCIe link lost, device now
detached
[ 141.351019] igb 0000:01:00.1 enp1s0f1: PCIe link lost, device now
detached
[ 143.465904] pcieport 0000:00:1c.0: Root Port link has been reset
[ 143.465994] igb 0000:01:00.1: broadcast slot_reset message
[ 143.466039] igb 0000:01:00.0: enabling device (0000 -> 0002)
[ 144.389078] igb 0000:01:00.1: enabling device (0000 -> 0002)
[ 145.312078] igb 0000:01:00.1: broadcast resume message
[ 145.322211] BUG: unable to handle kernel paging request at
0000000000003818
[ 145.361275] IP: [<ffffffffa02fd38d>]
igb_configure_tx_ring+0x14d/0x280 [igb]
[ 145.400048] PGD 0
[ 145.438007] Oops: 0002 [#1] SMP
A similar issue & solution could be found at:
http://patchwork.ozlabs.org/patch/689592/
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes firmware may not properly initialize I347AT4_PAGE_SELECT causing
the probe of an igb i210 NIC to fail. This patch adds an addition zeroing
of this register during igb_get_phy_id to workaround this issue.
Thanks for Jochen Henneberg for the idea and original patch.
Signed-off-by: Chris J Arges <christopherarges@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During systemd reboot sequence network driver interface is shutdown
by e1000_close. The PCI driver interface is shut by e1000_shutdown.
The e1000_shutdown checks for netif_running status, if still up it
brings down driver. But it disables msi outside of this if statement,
regardless of netif status. All this is OK when e1000_close happens
after shutdown. However, by default, everything in systemd is done
in parallel. This creates a conditions where e1000_shutdown is called
after e1000_close, therefore hitting BUG_ON assert in free_msi_irqs.
CC: xe-kernel@external.cisco.com
Signed-off-by: khalidm <khalidm@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the xcast mailbox message to include support for
unicast promiscuous mode. To allow a VF to enter this mode the PF
must be in promiscuous mode.
A later patch will add the support needed in the VF driver (ixgbevf)
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.
Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane. Without this patch the link remains at
1G when resuming from low power after being downshifted by LPLU.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx timestamp does not work on 82599 and X540 because bitwise operation
of RX_HWTSTAMP flags is incorrect and ixgbe_ptp_rx_hwtstamp() is never
called. This patch fixes it to enable Rx timestamp on 82599 and X540.
Without this fix:
ptp4l[278.730]: selected /dev/ptp8 as PTP clock
ptp4l[278.733]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.733]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.834]: port 1: received SYNC without timestamp
ptp4l[278.835]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[279.834]: port 1: received SYNC without timestamp
ptp4l[280.834]: port 1: received SYNC without timestamp
ptp4l[281.834]: port 1: received SYNC without timestamp
ptp4l[282.834]: port 1: received SYNC without timestamp
ptp4l[282.835]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[282.835]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[283.834]: port 1: received SYNC without timestamp
With this fix:
ptp4l[239.154]: selected /dev/ptp8 as PTP clock
ptp4l[239.157]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[239.157]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[240.989]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[244.989]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[244.989]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[246.977]: master offset -899583339542096 s0 freq +0 path delay 16222
ptp4l[247.977]: master offset -899583339617265 s1 freq -75169 path delay 16177
ptp4l[248.977]: master offset -130 s2 freq -75299 path delay 16177
ptp4l[248.977]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[249.977]: master offset -9 s2 freq -75217 path delay 16177
ptp4l[250.977]: master offset 88 s2 freq -75123 path delay 16132
Fixes: a9763f3cb5 ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Yusuke Suzuki <yus-suzuki@uf.jp.nec.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure that we free the IRQs in ixgbevf_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbevf_remove() after a failed recovery from
AER error because the interrupts were not freed.
Also moved the down and free functions into ixgbevf_close_suspend()
same as with ixgbe.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two methods for setting mac addresses in a Macvlan, that
differentiate themselves in the function macvlan_set_mac_Address.
If the macvlan mode is passthru, then we use the dev_set_mac_address
method, otherwise we use the dev_uc api via macvlan_sync_addresses.
The latter method (which would stem from using any non-passthru mode,
like bridge, or vepa), calls down into the driver in a path that terminates
in ixgbevf_set_uc_addr_vf, which sends a IXGBE_VF_SET_MACVLAN message,
which causes the pf to spawn the noted error message. This occurs because
it appears that the guest is trying to delete the mac address of the macvlan
before adding another.
The other path in macvlan_set_mac_address uses dev_set_mac_address, which
calls into ixgbevf_set_mac which uses the IXGBE_VF_SET_MAC_ADDR to the
pf to set the macvlan mac address.
The discrepancy here is in the handlers. The handler function for
IXGBE_VF_SET_MAC_ADDR (ixgbe_set_vf_mac_addr) has a check for
the vfinfo[].trusted bit to allow the operation if the vf is trusted.
In comparison, the IXGBE_VF_SET_MACVLAN message handler
(ixgbe_set_vf_macvlan_msg) has no such check of the trusted bit.
Signed-off-by: Ken Cox <jkc@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an interface is part of a namespace it is possible that
ixgbevf_close() may be called while ixgbevf_suspend() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs()
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and check for !netif_device_present()
to avoid entering close while in suspend.
Also added rtnl locks to ixgbevf_queue_reset_subtask().
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();
Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BaseT adapters that are capable of supporting 100Mb are not reporting this
capability. This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic PHY reset check we had previously is not sufficient for the
ixgbe_phy_x550em_ext_t PHY type. Check 1.CC02.0 instead - same as
ixgbe_init_ext_t_x550().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some x550 devices require the driver version reported to its firmware; this
patch sends the driver version string to the firmware through the host
interface command for x550 devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.
The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.
Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.
Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.
The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.
Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.
Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.
Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.
Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.
Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.
Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.
This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.
The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.
Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
