This patch reads charge delay from tsc DT node and writes to
REG_CHARGEDELAY register. If the charge delay is not specified in DT then
default value of 0x400(CHARGEDLY_OPENDLY) is used.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TSC interrupt handler had udelay to avoid reporting of false pen-up
interrupt to user space. This patch implements workaround suggesting in
Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay and
touchscreen lag. This also improves performance of touchscreen and
eliminates sudden jump of cursor at touch release.
IDLECONFIG and CHARGECONFIG registers are to be configured with same values
in order to eliminate false pen-up events. This workaround may result in
false pen-down to be detected, hence considerable charge step delay needs
to be added. The charge delay is set to 0xB000 (in terms of ADC clock
cycles) by default.
TSC steps are disabled at the end of every sampling cycle and EOS bit is
set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
next sampling cycle.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
"Just a few quirks for PS/2 this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add more Fujtisu notebooks to force crc_enabled
Input: i8042 - add noloop quirk for Medion Akoya E7225 (MD98857)
Input: synaptics - adjust min/max for Lenovo ThinkPad X1 Carbon 2nd
Some devices are not fast enough to differentiate between a fast-moving
contact and a new contact. This problem cannot be fully resolved because
information is truly missing, but it is possible to safe-guard against
obvious mistakes by restricting movement with a maximum displacement.
The new problem formulation for dmax > 0 cannot benefit from the speedup
for positive definite matrices, but since the convergence is faster, the
result is about the same. For a handful of contacts, the latency difference
is truly negligible.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded drv2667-haptics modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded drv260x-haptics modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded cap11xx modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Daniel Mack <linux@zonque.org>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Allwinner A31 SoC (sun6i) has the same resistive touchpanel controller
as on other sunxi platforms. The only difference between the variants is
the control bits for enabling operations are left-shifted by 1 on the A31.
Also update the comment for the original temperature sensor with
information from Allwinner.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver implements support for PS2 controller found on Allwinner A10,
A20 SOCs. It has been tested on A20 Olimex-Lime2 board and also on A10.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To allow for different firmware sizes let's replace the original size check
with with checking the signature in the firmware data.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fixes to the X.org driver have been applied long time ago and
the patch on kernel.org has long since gone so let's remove the
comment.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without this the aux port does not get detected, and consequently the touchpad
will not work.
With this patch the touchpad is detected:
$ dmesg | grep -E "(SYN|i8042|serio)"
pnp 00:03: Plug and Play ACPI device, IDs SYN1d22 PNP0f13 (active)
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126800, board id: 2863, fw id: 1473085
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
dmidecode excerpt for this laptop is:
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Medion
Product Name: Akoya E7225
Version: 1.0
Cc: stable@vger.kernel.org
Signed-off-by: Jochen Hein <jochen@jochen.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If "(count == NAME_MAX)" then we could end up putting the NUL terminator
one space beyond the end of the fw_name[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gen5_bl_metadata_row_params structure has its fields specified with
explicit endianness, so we should not be trying to convert to native CPU
endianness when filling the structure.
Also fix firmware validation checks and misspelled field in
gen5_bl_metadata_row_params.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Dudley Du <dudl@cypress.com>
Tested-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - fix ioctl nr overflow for UI_GET_SYSNAME/VERSION
Input: I8042 - add Acer Aspire 7738 to the nomux list
Input: elantech - support new ICs types for version 4
Input: i8042 - reset keyboard to fix Elantech touchpad detection
MAINTAINERS: remove Dmitry Torokhov's alternate address
Add acpi device tree support.
acpi device id "CYAP0000" is for old gen3 trackpad devices.
acpi device id "CYAP0001" is for new gen5 trackpad devices.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add force re-calibrate function support for gen5 trackpad device, it can be
used through sysfs calibrate interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add read baseline function support for gen5 trackpad device, it can be used
through sysfs baseline interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add firmware image update support for gen5 trackpad device, it can be used
through sysfs update_fw interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add force re-calibrate function support for gen3 trackpad device, it can be
used through sysfs calibrate interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add read baseline function supported for gen3 trackpad device, it can be
used through sysfs baseline interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for firmware image update for gen3 trackpad devices; the
firmware update is initiated by writing to update_fw sysfs attribute.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce control interfaces that are commonly used in pre- and after
production, for trackpad device state checking, managing and firmware image
updating. These interfaces include mode, firmware_version and product_id
interfaces for reading firmware version and trackpad device product id
values, and update_fw interface to command firmware image update process.
There are also baseline and calibrate interfaces for reading and checking
trackpad device's sensors states.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change implements runtime PM support in the driver and adds
runtime_suspend_scanrate_ms power management interface in device's power
group, so users or applications can control the runtime power management
strategy of trackpad device according to their requirements.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add suspend_scanrate_ms power management interfaces in device's
power group, so users or applications can control the power management
strategy of trackpad device according to their requirements.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for Gen5 Cypress trackpads. The driver detects
generation of the device at probe time and automatically selects
appropriate protocol.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple different chipsets and communication protocols
trackpad devices in one cyapa driver, the new cyapa driver is re-designed
with one cyapa driver core and multiple device specific functions component.
The cyapa driver core is contained in this patch, it supplies basic functions
that working with kernel and input subsystem, and also supplies the interfaces
that the specific devices' component can connect and work together with as
one driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen controller has a temperature sensor embedded in the SoC,
which already has hwmon support in the driver.
Add DT thermal zone support so we can use it with cpufreq for thermal
throttling.
This also adds a comment stating that we do not know the actual formula
for calculating the temperature.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When client changes the type of clock used for the time stamps in input
events flush pending events from the client's queue (since client would not
know which events have old time stamps and which ones have new ones) and
and queue SYN_DROPPED event.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure that driver does not process bogus packets as trackstick data
when there is no trackstick present and emit warnings in dmesg so potential
issues with trackstick handling will be visible for debugging.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change fixes name, product and version of dev2 input device based on
format used in function psmouse_switch_protocol() in file psmouse-base.c.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All the use cases in this driver has a regulator_haptic_toggle() call after
regulator_haptic_set_voltage(). So make regulator_haptic_set_voltage() call
regulator_haptic_toggle() to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of registering device attributes individually let's use attribute
groups and also devm_* infrastructure to ease cleanup.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for the Power Enable Key found on MFD AXP202
and AXP209. Besides the basic support for the button, the driver adds
two entries in sysfs to configure the time delay for power on/off.
Signed-off-by: Carlo Caione <carlo@caione.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wens@csie.org: made axp20x_pek_remove() static; removed driver owner
field; fixed path for sysfs entries]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If given input handler is not a filter there is no point is iterating list
of events in a packet to see if some of them need to be filtered out.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a device does not support autorepeat or does not emit any key events we
should not be scanning all events in a packet to decide if we should start
or stop autorepeat function.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some laptops, keyboard needs to be reset in order to successfully detect
touchpad (e.g., some Gigabyte laptop models with Elantech touchpads).
Without resettin keyboard touchpad pretends to be completely dead.
Based on the original patch by Mateusz Jończyk this version has been
expanded to include DMI based detection & application of the fix
automatically on the affected models of laptops. This has been confirmed to
fix problem by three users already on three different models of laptops.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81331
Cc: stable@vger.kernel.org
Signed-off-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Tested by: Zakariya Dehlawi <zdehlawi@gmail.com>
Tested-by: Guillaum Bouchard <guillaum.bouchard@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommended.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
