The prints after [k|v][m|z|c]alloc() functions are not needed,
because in case of failure, allocator will print their internal
error prints anyway.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull rmda fixes from Doug Ledford.
"First round of -rc fixes.
Due to various issues, I've been away and couldn't send a pull request
for about three weeks. There were a number of -rc patches that built
up in the meantime (some where there already from the early -rc
stages). Obviously, there were way too many to send now, so I tried to
pare the list down to the more important patches for the -rc cycle.
Most of the code has had plenty of soak time at the various vendor's
testing setups, so I doubt there will be another -rc pull request this
cycle. I also tried to limit the patches to those with smaller
footprints, so even though a shortlog is longer than I would like, the
actual diffstat is mostly very small with the exception of just three
files that had more changes, and a couple files with pure removals.
Summary:
- Misc Intel hfi1 fixes
- Misc Mellanox mlx4, mlx5, and rxe fixes
- A couple cxgb4 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (34 commits)
iw_cxgb4: invalidate the mr when posting a read_w_inv wr
iw_cxgb4: set *bad_wr for post_send/post_recv errors
IB/rxe: Update qp state for user query
IB/rxe: Clear queue buffer when modifying QP to reset
IB/rxe: Fix handling of erroneous WR
IB/rxe: Fix kernel panic in UDP tunnel with GRO and RX checksum
IB/mlx4: Fix create CQ error flow
IB/mlx4: Check gid_index return value
IB/mlx5: Fix NULL pointer dereference on debug print
IB/mlx5: Fix fatal error dispatching
IB/mlx5: Resolve soft lock on massive reg MRs
IB/mlx5: Use cache line size to select CQE stride
IB/mlx5: Validate requested RQT size
IB/mlx5: Fix memory leak in query device
IB/core: Avoid unsigned int overflow in sg_alloc_table
IB/core: Add missing check for addr_resolve callback return value
IB/core: Set routable RoCE gid type for ipv4/ipv6 networks
IB/cm: Mark stale CM id's whenever the mad agent was unregistered
IB/uverbs: Fix leak of XRC target QPs
IB/hfi1: Remove incorrect IS_ERR check
...
Also, rearrange things a bit to have a common c4iw_invalidate_mr()
function used everywhere that we need to invalidate.
Fixes: 49b53a93a6 ("iw_cxgb4: add fast-path for small REG_MR operations")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There are a few cases in c4iw_post_send() and c4iw_post_receive()
where *bad_wr is not set when an error is returned. This can
cause a crash if the application tries to use bad_wr.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Report the correct speed in the port attributes when using a 56Gbps
ethernet link. Without this change the field is incorrectly set to 10.
Fixes: a9c766bb75 ('IB/mlx4: Fix info returned when querying IBoE ports')
Fixes: 2e96691c31 ('IB: Use central enum for speed instead of hard-coded values')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If OpenSM runs over a ConnectX-3, and there are ConnectX-4 or Connect-IB
VFs active on the network, the OpenSM will receive QP1 packets containing
a GRH where the destination GID is the "Well-Known GID" -- which is not a
GID in the HCA Port's GID Table.
This GID must be tested-for separately -- and packets which contain
this destination GID should be routed to slave 0 (the PF).
Fixes: 37bfc7c1e8 ('IB/mlx4: SR-IOV multiplex and demultiplex MADs')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When MAD arrives to the hypervisor, we need to identify which slave it
should be sent by destination GID. When L3 protocol is IPv4 the
GRH is replaced by an IPv4 header. This patch detects when IPv4 header
needs to be parsed instead of GRH.
Fixes: b6ffaeffae ('mlx4: In RoCE allow guests to have multiple GIDS')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set traffic class within sl_tclass_flowlabel when create iboe AH.
Without this the TOS value will be empty when running VLAN tagged
traffic, because the TOS value is taken from the traffic class in the
address handle attributes.
Fixes: 9106c41069 ('IB/mlx4: Fix SL to 802.1Q priority-bits mapping for IBoE')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The maximum page size in the mkey context is 2GB.
Until today, we didn't enforce this requirement in the code,
and therefore, if we got a page size larger than 2GB, we
have passed zeros in the log_page_shift instead of the actual value
and the registration failed.
This patch limits the driver to use compound pages of 2GB for mkeys.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add the 512 bytes limit of RDMA READ and the size of remote
address to the max SGE calculation.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Wait before continuing unload till all pending mkey async creation requests
are done.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We put INT_MAX since this is the max value that can be held.
Though there is no hardware limitation, this is practically
a large enough number so we can use it.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove from the driver the limitation imposed by firmware check
to not allow change of atomic permissions for indirect UMRs.
In order to avoid failures on old firmware, we only ask for change
of atomic permissions if atomic operations are supported.
Fixes: 968e78dd96 ('IB/mlx5: Enhance UMR support to allow partial page table update')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Replace the pre-defined macro signifying inline umr instead
of the numerical constant.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, if ib_copy_to_udata fails, the CQ
won't be deleted from the radix tree and the HW (HW2SW).
Fixes: 225c7b1fee ('IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When an internal error condition is detected, make sure to set the
device inactive after dispatching the event so ULPs can get a
notification of this event.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When calling reg_mr of large MRs (e.g. 4GB) from multiple processes
and MR caches can't supply the required amount of MRs the slow-path
of MR allocation may be used. In this case we need to serialize the
slow-path between the processes to avoid soft lock.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When creating kernel CQs use 128B CQE stride if the
cache line size is 128B, 64B otherwise. This prevents
multiple CQEs from residing in a 128B cache line,
which can cause retries when there are concurrent
read and writes in one cache line.
Tested with IPoIB on PPC64, saw ~5% throughput
improvement.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Validate that the requested size of RQT is supported by firmware.
Fixes: c5f9092936 ('IB/mlx5: Add Receive Work Queue Indirection table operations')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Both pio_buf and send_context structs have oversized
fields and have cachelines that can be optimized.
Reduce oversized fields for both structs.
Make sure pio_buf struct fits within a cacheline.
Move read-only fields to their own cacheline in
send_context struct.
All of this will avoid cacheline trading as the ring
progresses and pio buffers/send contexts are used.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Profiling shows hot path struct members that need
to be in a minimum set of cachelines.
Group these struct member in the same cacheline:
sc2vl_lock
sc2vl
rhf_rcv_function_map
rcv_limit
rhf_offset
Group these struct member in the same cacheline:
process_pio_send
process_dma_send
pport
rcd
int_counter
flags
num_pports
first_user_ctxt
Fill holes in struct hfi1_devdata revealed by pahole.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Short circuit sdma_txclean() by adding an __sdma_txclean()
that is only called when the tx has sdma mappings.
Convert internal calls to __sdma_txclean().
This removes a call from the critical path.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Profiling suggests that the read_seqbegin() in
the txreq put logic is colliding with other uses
of the iowait lock.
The packet at a time use of this lock dictates a unique
lock to avoid reader/writer collisions when the number
of vTxWait events is low.
In order to support a unique lock the iowait struct embedded
in the QP is extended to remember the lock that protects the queue
head.
The QP destroy removes that QP from any wait list. It doesn't
need to know the head because of the linked list API, but it does
need to know the lock required to protect the head.
This also opens up the wait logic to have unique per resources locks
which needs to be in future refinement.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A few snoop related variables were missed in the snoop/capture removal
to get out of staging. Go back and clean those up too.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the function hfi1_create_ctxts the array "dd->rcd" is allocated and
then populated with allocated resources in a loop. Previously, if
error happened during the loop, only resource allocated in the current
iteration would be freed. The array itself would then be freed, leaving
the resources that were allocated in previous iterations and referenced
by the array elements in limbo.
This patch makes sure all allocated resources are freed before freeing
the array "dd->rcd". Also the resource allocation now takes account of
the numa node the device is attached to.
Reviewed-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fixes an Oops on device unbind, when the device is used
by a PSM user process. PSM processes access device resources which
are freed on device removal. Similar protection exists in uverbs
in ib_core for Verbs clients, but PSM doesn't use ib_uverbs hence
a separate protection is required for PSM clients.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The IRQ affinity entry is not needed after the irq notifier patch has been
added to the hfi1 driver.
The irq affinity settings for SDMA engine should be set using the standard
/proc/irq/<N>/ interface.
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support steering rules which add encapsulation headers,
encap_id parameter is needed.
Add new mlx5_flow_act struct which holds action related parameter:
action, flow_tag and encap_id. Use mlx5_flow_act struct when adding a new
steering rule.
This patch doesn't change any functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating flow tables, allow the caller to specify creation flags.
Currently no flags are used and as such this patch doesn't add any new
functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
