Just a few small fixes.
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: always apply pci shutdown callbacks"
drm/amdgpu: fix unload driver issue for virtual display
drm/amdgpu: check ring being ready before using
Single fence fix.
* tag 'drm-misc-fixes-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc:
drm/fence: fix memory overwrite when setting out_fence fd
CEA-861-F tells us:
"When transmitting any RGB colorimetry, the Source should set the
YQ-field to match the RGB Quantization Range being transmitted
(e.g., when Limited Range RGB, set YQ=0 or when Full Range RGB,
set YQ=1) and the Sink shall ignore the YQ-field."
So let's go ahead and do that. Perhaps there are sinks that don't
ignore the YQ as they should for RGB?
I wasn't able to find similar text in CEA-861-E, so it would seem
to be a fairly "recent" addition.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
HDMI 2.0 recommends that we set the Q bits in the AVI infoframe
even when the sink does not support quantization range selection (QS=0).
According to CEA-861 we can do that as long as the Q we send matches
the default quantization range for the mode.
Previously I think I had misread the spec as saying that you can't
send a non-zero Q at all when QS=0. But that's not what the spec
actually says.
v2: Fix typo in commit message (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Hardware has multiple (2 or 3, depending on model) stride
registers per layer; add a function that correctly takes that
into account. On hardware that only has 2 stride registers,
ensure that 3-plane (YUV) content has identical strides
for both chroma planes.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Removed smart layer stride setup, comment and commit message clarifications]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add the fb->offset[] value to the plane's physical start address
registe. Without that, packed formats are rendered incorrectly.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
If the device-tree 'reg' node doesn't reserve enough
space for the DP, fail to bind.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[renamed added function to malidp_has_sufficient_address_space]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
We're going to use the same format list for output formats, so rename
everything related to input formats to avoid confusion.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[touched commit title to clarify the final struct name]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.
The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.
v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com
This patch adds support to handle automated DP compliance
link training test requests. This patch has been tested with
Unigraf DPR-120 DP Compliance device for testing Link
Training Compliance.
After we get a short pulse Compliance test request, test
request values are read and hotplug uevent is sent in order
to trigger another modeset during which the pipe is configured
and link is retrained and enabled for link parameters requested
by the test.
v5:
* Only modify the compliance structure after all validation
is done (Jani Nikula)
* Remove the variable test_result (Jani Nikula)
v4:
* Return TEST_NAK for read failures and invalid
values (Jani Nikula)
* Conver the test link BW to link rate before storing (Jani Nikula)
v3:
* Validate the test link rate and lane count as soon as
the request comes (Jani Nikula)
v2:
* Validate the test lane count before using it in
intel_dp_compute_config (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274594-17361-1-git-send-email-manasi.d.navare@intel.com
Since tweaking i915_vma_compare() we allowed constructors to skip
clearing the ggtt_view believing that we didn't access the unused
members. That, as it turns out, was not entirely true. In particular,
i915_gem_fault() uses
ret = remap_io_mapping(area,
area->vm_start + (vma->ggtt_view.partial.offset << PAGE_SHIFT),
(ggtt->mappable_base + vma->node.start) >> PAGE_SHIFT,
min_t(u64, vma->size, area->vm_end - area->vm_start),
&ggtt->mappable);
i.e. the ggtt_view.partial for both normal and partial views. If we
allowed garbage into the normal vma->ggtt_view and then try userspace
tried to mmap it, we could explode in an unobvious fashion.
Fixes: 7b92c047ba ("drm/i915: Eliminate superfluous i915_ggtt_view_rotated")
Fixes: 3bf4d57519 ("drm/i915: Stop clearing i915_ggtt_view")
Reported-by: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123145245.3972-1-chris@chris-wilson.co.uk
Tested-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
(cherry picked from commit 7c51846030)
The display has a 18-Bit parallel LCD interface, require DE to be
active high and data driven by the controller on falling pixel
clock edge (display samples on rising edge).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The E231732 is a 7" panel with a resolution of 1024x600.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[treding@nvidia.com: add missing device tree binding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BOE NV101WXMN51 is a 10.1" WXGA color active matrix TFT LCD module
using amorphous silicon TFT's as an active switching devices. It can be
supported by the simple-panel driver.
Read the panel default EDID information:
EDID MODE DETAILS
name = <NULL>
pixel_clock = 71900
lvds_dual_channel = 0
refresh = 0
ha = 1280
hbl = 160
hso = 48
hspw = 32
hborder = 0
va = 800
vbl = 32
vso = 3
vspw = 5
vborder = 0
phsync = +
pvsync = -
x_mm = 0
y_mm = 0
drm_display_mode
.hdisplay = 1280
.hsync_start = 1328
.hsync_end = 1360
.htotal = 1440
.vdisplay = 800
.vsync_start = 803
.vsync_end = 808
.vtotal = 832
There are two modes in the EDID:
Detailed mode1: Clock 71.900 MHz, 216 mm x 135 mm
1280 1328 1360 1440 hborder 0
800 803 808 832 vborder 0
+hsync -vsync
Detailed mode2: Clock 57.500 MHz, 216 mm x 135 mm
1280 1328 1360 1440 hborder 0
800 803 808 832 vborder 0
+hsync -vsync
Support both of these modes on the panel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit 3846fd9b86.
There were some precursor commits missing for this around connector
locking, we should probably merge Lyude's nouveau avoid the problem patch.
After going through all the trouble of splitting out parts from
drm_crtc.[hc] and then properly documenting each I've entirely
forgotten to show the same TLC for CRTCs themselves!
Let's make amends asap.
v2: Review from Eric.
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Notifiations like mode change, hot plug and edid to
the audio driver are added. This is inturn used by the
audio driver for its functionality.
A new interface file capturing the notifications needed by the
audio driver is added
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
gvt-fixes-2017-01-25
- re-enable shadow batch buffer for security that was falsely turned off.
- kvmgt/mdev typo fix for correct ABI
- gvt mail list change
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
