Extend existing DA9062 binding information to include the DA9061 PMIC for
MFD core and regulators.
Add a da9062-onkey link to the existing onkey binding file.
Add a da9062-thermal link to the new temperature monitoring binding file.
Delete the da9062-watchdog section and replace it with a link to the new
DA9061/62 binding information file.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds description for LED as the sub-module on MT6397/MT6323
multifunction device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".
Fixes: 204ae2963e ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The described GPIO reset property is applicable to *all* child PHYs. If
we have one reset line per PHY present on the MDIO bus, these
automatically become properties of the child PHY nodes.
Finally, indicate how the RESET pulse width must be defined, which is
the maximum value of all individual PHYs RESET pulse widths determined
by reading their datasheets.
Fixes: 69226896ad ("mdio_bus: Issue GPIO RESET to PHYs.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation of device tree bindings for the
STM32 SAI ASoC driver.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements consideration of the SPI_READY mode flag as
defined in spi.h. It extends the device tree bindings to support
the values defined by the reference manual for the DRCTL field.
Thus supporting edge-triggered and level-triggered bursts.
Signed-off-by: Leif Middelschulte <Leif.Middelschulte@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The old NAND bindings were not exactly describing the hardware topology
and were preventing definitions of several NAND chips under the same
NAND controller.
New bindings address these limitations and should be preferred over the
old ones for new SoCs/boards.
Old bindings are still supported for backward compatibility but are
marked deprecated in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Adds the device tree bindings description for Samsung S3C24XX
MMC/SD/SDIO controller, used as a connectivity interface with external
MMC, SD and SDIO storage mediums.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTS properties are used instead of fixed data
because PHY settings can be different for different chips/boards.
Add description of new DLL PHY delays.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add description for mediatek,hs200-cmd-int-delay
Add description for mediatek,hs400-cmd-int-delay
Add description for mediatek,hs400-cmd-resp-sel-rising
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is the other SD controller on the platform, which can be swapped
to the role of SD card host using pin muxing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller found on Tegra186 in very similar to the controller
found on earlier generations of Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The list of compatible strings is somewhat difficult to read and extend.
Reformat it into a list to make it more easily extensible.
While at it, also remove the "plus one of the above" clause because it
isn't actually valid.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a reference to the HPLL to calculate debounce cycles. If the
clocks property is not supplied in the GPIO node then the consumer
should deny any debounce requests.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document the device tree binding for the pin controllers found on the
Armada 37xx SoCs.
Update the binding documention of the xtal clk which is a subnode of this
syscon node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Fixed gpios node]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 370/XP devices can 'blink' GPIO lines with a configurable on
and off period. This can be modelled as a PWM.
However, there are only two sets of PWM configuration registers for
all the GPIO lines. This driver simply allows a single GPIO line per
GPIO chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.
Due to the interleaving of registers it is not simple to separate the
PWM driver from the GPIO driver. Thus the GPIO driver has been
extended with a PWM driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
* Port forward
* Merge PWM portion into gpio-mvebu.c
* Switch to atomic PWM API
* Add new compatible string marvell,armada-370-xp-gpio
* Update and merge documentation patch
* Update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Ortiz says:
====================
NFC 4.12 pull request
This is the NFC pull request for 4.12. We have:
- Improvements for the pn533 command queue handling and device
registration order.
- Removal of platform data for the pn544 and st21nfca drivers.
- Additional device tree options to support more trf7970a hardware options.
- Support for Sony's RC-S380P through the port100 driver.
- Removal of the obsolte nfcwilink driver.
- Headers inclusion cleanups (miscdevice.h, unaligned.h) for many drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds DT binding documentation for Odroid XU3/4
sound subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the chip the IMON signal is a full 24-bits however normally only
some of the bits will be sent over the bus. The chip provides a field
to select which bits of the IMON will be sent back, this is the only
feedback signal that has this feature.
Add an additional entry to the cirrus,imon device tree property to
allow the IMON scale parameter to be passed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull PCI fix from Bjorn Helgaas:
"Sorry this is so late. It's been in -next for over a week, but I
forgot to send it on until now.
A single fix to the DT binding of the HiSilicon PCIe host support"
* tag 'pci-v4.11-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hisi: Fix DT binding (hisi-pcie-almost-ecam)
We actually can't allow the missing of the regualor name, thus update
the binding doc to make regulator-name property to be required.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow setting AUS mode for a display from the device tree. Use an
optional boolean property. AUS mode can be set only on imx21 and
compatible chipsets.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Document the devicetree bindings for Mediatek random number
generator which could be found on MT7623 SoC or other similar
Mediatek SoCs.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 42d5ec9547 ("fpga: add config complete timeout") introduced the
config complete property but didn't include the corresponding DT binding
documentation. Add it now.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The hardware has a LPI interrupt.
There is already code in the stmmac driver to parse and handle the
interrupt. However, this information was missing from the DT binding.
At the same time, improve the description of the existing interrupts.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
