Support for reducing the number of nodes and memory consumption of the rbtree
cache by allowing for small unused holes in the node's register cache block was
initially added in commit 0c7ed856 ("regmap: Cut down on the average # of nodes
in the rbtree cache"). But the commit had problems and so its effect was
reverted again in commit 4e67fb5 ("regmap: rbtree: Fix overlapping rbnodes.").
This patch brings the feature back of reducing the average number of nodes,
which will speedup node look-up, while at the same time also reducing the memory
usage of the rbtree cache. This patch takes a slightly different approach than
the original patch though. It modifies the adjacent node look-up to not only
consider nodes that are just one to the left or the right of the register but
any node that falls in a certain range around the register. The range is
calculated based on how much memory it would take to allocate a new node
compared to how much memory it takes adding a set of unused registers to an
existing node. E.g. if a node takes up 24 bytes and each register in a block
uses 1 byte the range will be from the register address - 24 to the register
address + 24. If we find a node that falls within this range it is cheaper or as
expensive to add the register to the existing node and have a couple of unused
registers in the node's cache compared to allocating a new node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
A register which is adjacent to a node will either be left to the first
register or right to the last register. It will not be within the node's range,
so there is no point in checking for each register cached by the node whether
the new register is next to it. It is sufficient to check whether the register
comes before the first register or after the last register of the node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regmap_debugfs_get_dump_start() function maps from a file offset to the
register that can be found at that position in the file. This is done using a
look-up table. Commit d6814a7d ("regmap: debugfs: Suppress cache for partial
register files") added a check to bypass the look-up table for partial register
files, since the offsets in that table are only correct for the full register
file. The check incorrectly uses the file offset instead of the register base
address and returns it. This will cause the file offset to be interpreted as a
register address which will result in a incorrect output from the registers file
for all reads except at position 0.
The issue can easily be reproduced by doing small reads the registers file, e.g.
`dd if=registers bs=10 count=5`.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
There are a couple of calculations, which convert between register addresses and
block indices, in regcache_rbtree_sync() and regcache_rbtree_node_alloc() which
assume that reg_stride is 1. This will break the rb cache for configurations
which do not use a reg_stride of 1.
Also rename 'base' in regcache_rbtree_sync() to 'start' to avoid confusion with
'base_reg'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch cleans the initialization of dma contiguous framework. The
all-in-one dma_declare_contiguous() function is now separated into
dma_contiguous_reserve_area() which only steals the the memory from
memblock allocator and dma_contiguous_add_device() function, which
assigns given device to the specified reserved memory area. This improves
the flexibility in defining contiguous memory areas and assigning device
to them, because now it is possible to assign more than one device to
the given contiguous memory area. Such split in initialization procedure
is also required for upcoming device tree support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
* pm-cpufreq: (60 commits)
cpufreq: pmac32-cpufreq: remove device tree parsing for cpu nodes
cpufreq: pmac64-cpufreq: remove device tree parsing for cpu nodes
cpufreq: maple-cpufreq: remove device tree parsing for cpu nodes
cpufreq: arm_big_little: remove device tree parsing for cpu nodes
cpufreq: kirkwood-cpufreq: remove device tree parsing for cpu nodes
cpufreq: spear-cpufreq: remove device tree parsing for cpu nodes
cpufreq: highbank-cpufreq: remove device tree parsing for cpu nodes
cpufreq: cpufreq-cpu0: remove device tree parsing for cpu nodes
cpufreq: imx6q-cpufreq: remove device tree parsing for cpu nodes
drivers/bus: arm-cci: avoid parsing DT for cpu device nodes
ARM: mvebu: remove device tree parsing for cpu nodes
ARM: topology: remove hwid/MPIDR dependency from cpu_capacity
of/device: add helper to get cpu device node from logical cpu index
driver/core: cpu: initialize of_node in cpu's device struture
ARM: DT/kernel: define ARM specific arch_match_cpu_phys_id
of: move of_get_cpu_node implementation to DT core library
powerpc: refactor of_get_cpu_node to support other architectures
openrisc: remove undefined of_get_cpu_node declaration
microblaze: remove undefined of_get_cpu_node declaration
cpufreq: fix bad unlock balance on !CONFIG_SMP
...
Use __ATTR_RW() instead of __ATTR() to make it more obvious what the
type of attribute is being created.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_RO() instead of a "raw" __ATTR macro, making it easier
to audit exactly what is going on with the sysfs files.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two bus attributes that can better be defined using
DRIVER_ATTR_WO(), so convert them to the new macro, making it easier to
audit attribute permissions.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the platform bus code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gotta love a macro that doesn't reduce the typing you have to do.
Also, only the driver core, and one network driver uses this. The
driver core functions will be going away soon, and I'll convert the
network driver soon to not need this as well, so delete it for now
before anyone else gets some bright ideas and wants to use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions are being open-coded in 3 different places in the driver
core, and other driver subsystems will want to start doing this as well,
so move it to the sysfs core to keep it all in one place, where we know
it is written properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two ways to set the online/offline state for a memory block:
echo 0|1 > online and echo online|online_kernel|online_movable|offline >
state.
The state attribute can online a memory block with extra data, the
"online type", where the online attribute uses a default online type of
ONLINE_KEEP, same as echo online > state.
Currently there is a state_mutex that provides consistency between the
memory block state and the underlying memory.
The problem is that this code does a lot of things that the common
device layer can do for us, such as the serialization of the
online/offline handlers using the device lock, setting the dev->offline
field, and calling kobject_uevent().
This patch refactors the online/offline code to allow the common
device_[online|offline] functions to be used. The result is a simpler
and more common code path for the two state setting mechanisms. It also
removes the state_mutex from the struct memory_block as the memory block
device lock provides the state consistency.
No functional change is intended by this patch.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now memory_dev_init() maintains the memory block pointer
between iterations of add_memory_section(). This is nasty.
This patch refactors add_memory_section() to become add_memory_block().
The refactoring pulls the section scanning out of memory_dev_init()
and simplifies the signature.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The path through add_memory_section() when the memory block already
exists uses flawed refcounting logic. A get_device() is done on a
memory block using a pointer that might not be valid as we dropped
our previous reference and didn't obtain a new reference in the
proper way.
Lets stop pretending and just remove the get/put. The
mem_sysfs_mutex, which we hold over the entire init loop now, will
prevent the memory blocks from disappearing from under us.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that add_memory_section() is only called from boot time, reduce
the logic and remove the enum.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add_memory_section() is currently called from both boot time and run
time via hotplug and there is a lot of nastiness to allow for shared
code including an enum parameter to convey the calling context to
add_memory_section().
This patch is the first step in breaking up the messy code sharing by
pulling the hotplug path for add_memory_section() directly into
register_new_memory().
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the [get|put]_device functions for ref'ing the memory block device
rather than the kobject functions which should be hidden away by the
device layer.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in releasing the mutex for each section that is added
during boot time. Just hold it over the entire initialization loop.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
CPUs are also registered as devices but the of_node in these cpu
devices are not initialized. Currently different drivers requiring
to access cpu device node are parsing the nodes themselves and
initialising the of_node in cpu device.
The of_node in all the cpu devices needs to be initialized properly
and at one place. The best place to update this is CPU subsystem
driver when registering the cpu devices.
The OF/DT core library now provides of_get_cpu_node to retrieve a cpu
device node for a given logical index by abstracting the architecture
specific details.
This patch uses of_get_cpu_node to assign of_node when registering the
cpu devices.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
It may be useful to register multiple patches with regmap, for example
one that depends on the device revision and one that depends on the system
configuration. Add support for doing this, appending any new patches to
the existing patches.
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a potential race condition between cpu_subsys_online()
and either acpi_processor_remove() or remove_memory() that execute
try_offline_node(). Namely, it is possible that cpu_subsys_online()
will run right after the CPUs NUMA node has been put offline and
cpu_to_node() executed by it will return NUMA_NO_NODE (-1). In
that case the CPU is gone and it doesn't make sense to call cpu_up()
for it, so make cpu_subsys_online() return -ENODEV then.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add bus_groups to struct bus_type which should be used
instead of bus_attrs.
bus_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add drv_groups to struct bus_type which should be used
instead of drv_attrs.
drv_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute groups are much more flexible than just a list of attributes,
due to their support for visibility of the attributes, and binary
attributes. Add dev_groups to struct bus_type which should be used
instead of dev_attrs.
dev_attrs will be removed from the structure soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_writeable() check should not be done in
regcache_write() because this prevents read-only
registers to be cached. After a read on a read-only
register its value will not be stored in the cache
and the next time someone will try to read it the
value will be read from the bus instead of the
cache.
Instead the regmap_writeable() check should be done
in _regmap_write() to prevent callers from writing
to read-only registers.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the initial case when no reg_defaults values are
provided and no register value was added to the cache
yet, the cache_present bitmap is NULL. If this function
is invoked for any register it should return false
(i.e. the register is not cached) instead of true.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I see no reason why a virtual range shouldn't be allowed to cover its
own data window if the page selection register is in the same place
on every page.
For chips which use paged access for all of their registers, but only
when connected via I2C, and which can access the whole register space
directly when connected via SPI, this allows to avoid acrobatics with
the register ranges by simply mapping the I2C ranges over the data
window beginning at 0x0, and then using linear access for the SPI
variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
arch_provides_topology_pointers was introduced in commit 23ca4bba3 (x86:
cleanup early per cpu variables/accesses v4) to indicate pointers to the
topology cpumask_t maps are valid to avoid copying data on to/off of the
stack.
But later in commit fbd59a8d (cpumask: Use topology_core_cpumask()/
topology_thread_cpumask()), the pointers to the topology struct cpumask maps
are always valid.
After that commit, the only difference is that there is a redundant
"unsigned int cpu = dev->id;" if arch_provides_topology_pointers defined, but
dev->id is type 'u32' which devolves to 'unsigned int' on all supported arches.
So this arch_provides_topology_pointers define is pointless and only cause
obfuscation now, remove it.
Tested on x86 machine, topology information in sys/devices/system/cpu/
cpuX/topology/ is the same after appling this patch set.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new trace event is added to PM events to print the time it takes to
suspend and resume a device. It generates trace messages that
include device, driver, parent information in addition to the type of
PM ops invoked as well as the PM event and error status from the PM
ops. Example trace below:
bash-2239 [000] .... 290.883035: device_pm_report_time: backlight
acpi_video0 parent=0000:00:02.0 state=freeze ops=class nsecs=332 err=0
bash-2239 [000] .... 290.883041: device_pm_report_time: rfkill rf
kill3 parent=phy0 state=freeze ops=legacy class nsecs=216 err=0
bash-2239 [001] .... 290.973892: device_pm_report_time: ieee80211
phy0 parent=0000:01:00.0 state=freeze ops=legacy class nsecs=90846477 err=0
bash-2239 [001] .... 293.660129: device_pm_report_time: ieee80211 phy0 parent=0000:01:00.0 state=restore ops=legacy class nsecs=101295162 err=0
bash-2239 [001] .... 293.660147: device_pm_report_time: rfkill rfkill3 parent=phy0 state=restore ops=legacy class nsecs=1804 err=0
bash-2239 [001] .... 293.660157: device_pm_report_time: backlight acpi_video0 parent=0000:00:02.0 state=restore ops=class nsecs=757 err=0
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moved 11 calls to the EXPORT_SYMBOL_GPL beneath their respective functions per
checkpatch.pl warnings.
Signed-off-by: David Graham White <dgwhite11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the hardware interrupt mask register does not prevent the chip level
irq from being asserted by the corresponding interrupt status bit, already
set interrupt bits should to be cleared once after masking them during
initialization. Add a flag to let drivers enable this behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull driver core patches from Greg KH:
"Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups,
to solve that race condition, which was impossible to do before this,
so that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the
different subtrees, instead of having to live in my driver-core tree,
causing merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from
others didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting
to you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here
as well. All of these have been in linux-next this week, with no
reported problems"
* tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: fix new kernel-doc warning in base/platform.c
sysfs: use file mode defines from stat.h
sysfs: add more helper macro's for (bin_)attribute(_groups)
driver core: add default groups to struct class
driver core: Introduce device_create_groups
sysfs: prevent warning when only using binary attributes
sysfs: add support for binary attributes in groups
driver core: device.h: add RW and RO attribute macros
sysfs.h: add BIN_ATTR macro
sysfs.h: add ATTRIBUTE_GROUPS() macro
sysfs.h: add __ATTR_RW() macro
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
Fix new kernel-doc warning in drivers/base/platform.c:
Warning(drivers/base/platform.c:528): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
