SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The gianfar driver calls device_set_wakeup_enable() under a spinlock,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now. Fix this
by moving the device_set_wakeup_enable() call out of the
spinlock-protected area.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
Some Ax88790 chip need to reinitialize the CISREG_CCSR register
after resume.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add call to Firmware to reset its VF State when we first attach to the VF.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were some errors in the way that internal Gather Lists were being
translated into skb's. This also makes the VF Driver look more like the PF
Driver to facilitate easier comarison.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix botch in Generic Receive Offload (the Packet Gather List Total length
field wasn't being initialized).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't implement (struct net_device_ops *)->ndo_select_queue() with simple
call to skb_tx_hash(). This leads to non-persistent TX queue selection in
the Linux dev_pick_tx() routine for TCP connections.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol. However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol. This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags. Instead,
look inside the header if necessary to determine the correct
protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For device that supports VIRTIO_NET_F_STATUS, there's no need to
assume the link is up and we need to call nerif_carrier_off() before
querying device status, otherwise we may get wrong operstate after
diver was loaded because the link watch event was not fired as
expected.
For device that does not support VIRITO_NET_F_STATUS, we could not get
its status through virtnet_update_status() and what we can only do is
always assuming the link is up.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:
Don't bring the interface down and up, just reinit controller HW
and PHY.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: do not pass injected events back to the originating handler
Input: pcf8574_keypad - fix error handling in pcf8574_kp_probe
Input: acecad - fix a memory leak in usb_acecad_probe error path
Input: atkbd - add 'terminal' parameter for IBM Terminal keyboards
Input: i8042 - add Sony VAIOs to MUX blacklist
kgdboc: reset input devices (keyboards) when exiting debugger
Input: export input_reset_device() for use in KGDB
Input: adp5588-keys - unify common header defines
When a PCI bus has two resources with the same start/end, e.g.,
pci_bus 0000:04: resource 2 [mem 0xd0000000-0xd7ffffff pref]
pci_bus 0000:04: resource 7 [mem 0xd0000000-0xd7ffffff]
the previous pci_bus_find_resource_prev() implementation would alternate
between them forever:
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff])
returns [mem 0xd0000000-0xd7ffffff pref]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
...
This happened because there was no ordering between two resources with the
same start and end. A resource that had the same start and end as the
cursor, but was not itself the cursor, was considered to be before the
cursor.
This patch fixes the hang by making a fixed ordering between any two
resources.
In addition, it tries to allocate from positively decoded regions before
using any subtractively decoded resources. This means we will use a
positive decode region before a subtractive decode one, even if it means
using a smaller address.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=22062
Reported-by: Borislav Petkov <bp@amd64.org>
Tested-by: Borislav Petkov <bp@amd64.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
block: remove unused copy_io_context()
Documentation: remove anticipatory scheduler info
block: remove REQ_HARDBARRIER
ioprio: rcu_read_lock/unlock protect find_task_by_vpid call (V2)
ioprio: fix RCU locking around task dereference
block: ioctl: fix information leak to userland
block: read i_size with i_size_read()
cciss: fix proc warning on attempt to remove non-existant directory
bio: take care not overflow page count when mapping/copying user data
block: limit vec count in bio_kmalloc() and bio_alloc_map_data()
block: take care not to overflow when calculating total iov length
block: check for proper length of iov entries in blk_rq_map_user_iov()
cciss: remove controllers supported by hpsa
cciss: use usleep_range not msleep for small sleeps
cciss: limit commands allocated on reset_devices
cciss: Use kernel provided PCI state save and restore functions
cciss: fix board status waiting code
drbd: Removed checks for REQ_HARDBARRIER on incomming BIOs
drbd: REQ_HARDBARRIER -> REQ_FUA transition for meta data accesses
drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code
...
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (39 commits)
drm/ttm: Be consistent on ttm_bo_init() failures
drm/radeon/kms: Fix retrying ttm_bo_init() after it failed once.
drm/radeon/kms: fix thermal sensor reporting on rv6xx
drm/radeon/kms: fix bugs in ddc and cd path router code
drm/radeon/kms: add support for clock/data path routers
drm: vmwgfx: fix information leak to userland
drivers/gpu: Use vzalloc
drm/vmwgfx: Fix oops on failing bo pin
drm/ttm: Remove the CAP_SYS_ADMIN requirement for bo pinning
drm/ttm: Make sure a sync object doesn't disappear while we use it
drm/radeon/kms: don't disable shared encoders on pre-DCE3 display blocks
drivers/gpu/drm: Update WARN uses
drivers/gpu/drm/vmwgfx: Fix k.alloc switched arguments
DRM: ignore invalid EDID extensions
drm/radeon/kms: make the connector code less verbose
drm/ttm: remove failed ttm binding error printout
drm/ttm: Add a barrier when unreserving
drm/ttm: Remove mm init error printouts and checks
drm/ttm: Remove pointless list_empty check
drm/ttm: Use private locks for the default bo range manager
...
This affects the get/set of the current Ambient Light Zone. Reading
should return an integer between 1..3 (1 = Daylight, 2 = office, 3 =
dark). Writing a value between 1..3 forces the backlight controller to
enter the corresponding Ambient Light Zone. Writing 0 returns to normal
operation.
Fix valid range checking so we don't write invalid values to the
controller, and make sure we subtract 1, since this is what the register
definition (CFGR:BLV) requires. Otherwise the values written don't work
correctly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intensity of the backlight can be varied from a range of
max_brightness to zero. Though most, if not all the pwm based backlight
devices start flickering at lower brightness value. And also for each
device there exists a brightness value below which the backlight appears
to be turned off though the value is not equal to zero.
If the range of brightness for a device is from zero to max_brightness. A
graph is plotted for brightness Vs intensity for the pwm based backlight
device has to be a linear graph.
intensity
| /
| /
| /
|/
---------
0 max_brightness
But pratically on measuring the above we note that the intensity of
backlight goes to zero(OFF) when the value in not zero almost nearing to
zero(some x%). so the graph looks like
intensity
| /
| /
| /
| |
------------
0 x max_brightness
In order to overcome this drawback knowing this x% i.e nothing but the low
threshold beyond which the backlight is off and will have no effect, the
brightness value is being offset by the low threshold value(retaining the
linearity of the graph). Now the graph becomes
intensity
| /
| /
| /
| /
-------------
0 max_brightness
With this for each and every digit increment in the brightness from zero
there is a change in the intensity of backlight. Devices having this
behaviour can set the low threshold brightness(lth_brightness) and pass
the same as platform data else can have it as zero.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the event that none of the configs are set (CONFIG_LEDS_GPIO_PLATFORM,
CONFIG_LEDS_GPIO_OF, CONFIG_LEDS_GPIO_PLATFORM), we will return a bogus
value when initializing the module.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset provides support for LP5521 and LP5523 LED driver chips from
National Semicondutor. Both drivers supports programmable engines and
naturally LED class features.
Documentation is provided as a part of the patchset. I created "leds"
subdirectory under Documentation. Perhaps the rest of the leds*
documentation should be moved there.
Datasheets are freely available at National Semiconductor www pages.
This patch:
LP5521 chip is three channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, blinking LEDs can be awkward because it is not guaranteed that
all LEDs implement blinking. The trigger that wants it to blink then
needs to implement its own timer solution.
Rather than require that, add led_blink_set() API that triggers can use.
This function will attempt to use hw blinking, but if that fails
implements a timer for it. To stop blinking again, brightness_set() also
needs to be wrapped into API that will stop the software blink.
As a result of this, the timer trigger becomes a very trivial one, and
hopefully we can finally see triggers using blinking as well because it's
always easy to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a signedness bug so "ret" was never less than zero and that
breaks the error handling. Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1). It's easiest to just use
resource_size() which does the right thing.
I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations. This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:
port->iores.start = law_start;
port->iores.end = law_start + law_size - 1;
So I think this is the correct fix.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these warnings:
drivers/macintosh/adb-iop.c: In function `adb_iop_complete':
drivers/macintosh/adb-iop.c:85: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:92: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c: In function ¡adb_iop_listen¢:
drivers/macintosh/adb-iop.c:111: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:151: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMC hosts that poll for card detection by defining the MMC_CAP_NEEDS_POLL
flag have a race on rmmod, where the delayed work is cancelled without
waiting for completed polling. To prevent this a _sync version of the work
cancellation has to be used.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set VM_PFNMAP in the privcmd mmap file_op, rather than later in
xen_remap_domain_mfn_range when it is too late because
vma_wants_writenotify has already been called and vm_page_prot has
already been modified.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If the mux is configured with a large mru/mtu the existing code gets the
byte ordering wrong for the header.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port lock exists to protect these resources, so we need to grab it
before making changes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we are using early serial, don't let the normal console rewind
the log buffer, since that causes things to be printed multiple times.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to force a SSYNC here as the LSR register will already
be updated by the time we get back to reading it. This speeds up TX
throughput and lowers general system overhead (since SSYNC is system
wide, not peripheral-specific).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Blackfin systems, peripherals that have optional DMA support always
route their interrupts through the corresponding DMA channel -- even
when DMA is not being used. So in PIO mode, we still need to request
the DMA channel (so interrupts are delivered) which means we need to
always include the DMA header for the DMA defines/functions.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay Sievers pointed out that usage of POLLIN is well defined by POSIX,
and the current usage here doesn't follow that definition. So let's
duplicate the same semantics as implemented by sysfs_poll() instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@canonical.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/char/amiserial.c: In function ?rs_ioctl?:
drivers/char/amiserial.c:1302: warning: unused variable ?icount?
commit 0587102cf9 ("tty: icount changeover for
other main devices") removed the users, but not the actual variable.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
