Wifi catcher is a slider switch, that when slid past the on position
will emit an event that is intended for launching a wifi application
or applet when the machine is turned on.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
SPT LTR_IGN register provides a means to make the PMC ignore the LTR values
reported by the individual PCH devices.
echo <IP Offset> > /sys/kernel/debug/pmc_core/ltr_ignore.
When a particular IP Offset bit is set the PMC will ignore the LTR value
reported by the corresponding IP when the PMC performs the latency
coalescing.
IP Offset IP Name
0 SPA
1 SPB
2 SATA
3 GBE
4 XHCI
5 RSVD
6 ME
7 EVA
8 SPC
9 Azalia/ADSP
10 RSVD
11 LPSS
12 SPD
13 SPE
14 Camera
15 ESPI
16 SCC
17 ISH
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
[dvhart: pmc_core_ltr_ignore_write local declaration order cleanup]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
ModPhy Common lanes can provide the clock gating status for the important
system PLLs such as Gen2 USB3PCIE2 PLL, DMIPCIE3 PLL, SATA PLL and MIPI
PLL.
On SPT, in addition to the crystal oscillator clock, the 100Mhz Gen2
USB3PCI2 PLL clock is used as the PLL reference clock and Gen2 PLL idling
is a necessary condition for the platform to go into low power states like
PC10 and S0ix.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The PCH implements a number of High Speed I/O (HSIO) lanes that are split
between PCIe*, USB 3.0, SATA, GbE, USB OTG and SSIC. This patch shows the
current power gating status of the available ModPhy Core lanes. This is
done by sending a message to the PMC (MTPMC) that contains the XRAM
register offset for the MPHY_CORE_STS_0 and MPHY_CORE_STS_1 and then by
reading the response sent by the PMC (MFPMC).
While enabling low power modes we often encounter situations when the
ModPhy lanes are not power gated and it becomes hard to debug which lane is
active and which is not in the absence of an external hardware debugger
(JTAG/ITP). This patch eliminates the dependency on an external hardware
debugger for reading the ModPhy Lanes power gating status.
This patch requires PMC_READ_DISABLE setting to be disabled in the platform
bios.
cat /sys/kernel/debug/pmc_core/mphy_lanes_power_gating_status
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds the support for reading the power gating status of various
devices present on Sunrise Point PCH. This is intended to be used for
debugging purpose while tuning the platform for power optimizations and
also to understand which devices (on PCH) are blocking the system to enter
a low power state.
Power Management Controller on Sunrise Point PCH provides access to "PGD
PFET Enable Ack Status Registers (ppfear)". This patch reads and decodes
this register and dumps the output in formatted manner showing various
devices present on the PCH and their "Power Gating" status.
Further documentation can be found in Intel 7th Gen Core family mobile u/y
processor io datasheet volume 2.
Sample output (stripped and not in order):
cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
PMC State: Not Power gated
OPI-DMI State: Not Power gated
XHCI State: Power gated
LPSS State: Power gated
CSME_PSF State: Not power gated
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
On Sunrise Point PCH, the Power Management Controller provides 4K bytes of
memory space for various power management and debug registers. This fix is
needed to access power management & debug registers that are mapped at a
higher offset.
Also, this provides a fix for correctly masking the PWRMBASE as the initial
bits (0-11) are reserved.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The AMW0_GUID1 wmi is not only found on Acer family but also other
machines like Lenovo, Fujitsu and Medion. In the past, acer-wmi handled
those non-Acer machines by quirks list.
But actually acer-wmi driver was loaded on any machine that had
AMW0_GUID1. This behavior is strange because those machines should be
supported by appropriate wmi drivers. e.g. fujitsu-laptop,
ideapad-laptop.
This patch adds the logic to check the machine that has AMW0_GUID1
should be in Acer/Packard Bell/Gateway white list. But, it still keeps
the quirk list of those supported non-acer machines for backward
compatibility.
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull fbdev update from Tomi Valkeinen:
"No one has stepped up to take the job, so I've marked fbdev as orphan"
* tag 'fbdev-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fbdev: remove current maintainer
Pull VFIO updates from Alex Williamson:
- VFIO updates for v4.10 primarily include a new Mediated Device
interface, which essentially allows software defined devices to be
exposed to users through VFIO. The host vendor driver providing this
virtual device polices, or mediates user access to the device.
These devices often incorporate portions of real devices, for
instance the primary initial users of this interface expose vGPUs
which allow the user to map mediated devices, or mdevs, to a portion
of a physical GPU. QEMU composes these mdevs into PCI representations
using the existing VFIO user API. This enables both Intel KVM-GT
support, which is also expected to arrive into Linux mainline during
the v4.10 merge window, as well as NVIDIA vGPU, and also Channel I/O
devices (aka CCW devices) for s390 virtualization support. (Kirti
Wankhede, Neo Jia)
- Drop unnecessary uses of pcibios_err_to_errno() (Cao Jin)
- Fixes to VFIO capability chain handling (Eric Auger)
- Error handling fixes for fallout from mdev (Christophe JAILLET)
- Notifiers to expose struct kvm to mdev vendor drivers (Jike Song)
- type1 IOMMU model search fixes (Kirti Wankhede, Neo Jia)
* tag 'vfio-v4.10-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
vfio iommu type1: Fix size argument to vfio_find_dma() in pin_pages/unpin_pages
vfio iommu type1: Fix size argument to vfio_find_dma() during DMA UNMAP.
vfio iommu type1: WARN_ON if notifier block is not unregistered
kvm: set/clear kvm to/from vfio_group when group add/delete
vfio: support notifier chain in vfio_group
vfio: vfio_register_notifier: classify iommu notifier
vfio: Fix handling of error returned by 'vfio_group_get_from_dev()'
vfio: fix vfio_info_cap_add/shift
vfio/pci: Drop unnecessary pcibios_err_to_errno()
MAINTAINERS: Add entry VFIO based Mediated device drivers
docs: Sample driver to demonstrate how to use Mediated device framework.
docs: Sysfs ABI for mediated device framework
docs: Add Documentation for Mediated devices
vfio: Define device_api strings
vfio_platform: Updated to use vfio_set_irqs_validate_and_prepare()
vfio_pci: Updated to use vfio_set_irqs_validate_and_prepare()
vfio: Introduce vfio_set_irqs_validate_and_prepare()
vfio_pci: Update vfio_pci to use vfio_info_add_capability()
vfio: Introduce common function to add capabilities
vfio iommu: Add blocking notifier to notify DMA_UNMAP
...
Pull gcc plugins updates from Kees Cook:
"Minor changes to the gcc plugins:
- add the gcc plugins Makefile to MAINTAINERS to route things
correctly
- hide cyc_complexity behind !CONFIG_TEST for the future unhiding of
plugins generally"
* tag 'gcc-plugins-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Adjust Kconfig to avoid cyc_complexity
MAINTAINERS: add GCC plugins Makefile
Pull pstore updates from Kees Cook:
"Improvements and fixes to pstore subsystem:
- add additional checks for bad platform data
- remove bounce buffer in console writer
- protect read/unlink race with a mutex
- correctly give up during dump locking failures
- increase ftrace bandwidth by splitting ftrace buffers per CPU"
* tag 'pstore-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ramoops: add pdata NULL check to ramoops_probe
pstore: Convert console write to use ->write_buf
pstore: Protect unlink with read_mutex
pstore: Use global ftrace filters for function trace filtering
ftrace: Provide API to use global filtering for ftrace ops
pstore: Clarify context field przs as dprzs
pstore: improve error report for failed setup
pstore: Merge per-CPU ftrace records into one
pstore: Add ftrace timestamp counter
ramoops: Split ftrace buffer space into per-CPU zones
pstore: Make ramoops_init_przs generic for other prz arrays
pstore: Allow prz to control need for locking
pstore: Warn on PSTORE_TYPE_PMSG using deprecated function
pstore: Make spinlock per zone instead of global
pstore: Actually give up during locking failure
Patches queued up by Filipe:
The most important change is still the fix for the extent tree
corruption that happens due to balance when qgroups are enabled (a
regression introduced in 4.7 by a fix for a regression from the last
qgroups rework). This has been hitting SLE and openSUSE users and QA
very badly, where transactions keep getting aborted when running
delayed references leaving the root filesystem in RO mode and nearly
unusable. There are fixes here that allow us to run xfstests again
with the integrity checker enabled, which has been impossible since 4.8
(apparently I'm the only one running xfstests with the integrity
checker enabled, which is useful to validate dirtied leafs, like
checking if there are keys out of order, etc). The rest are just some
trivial fixes, most of them tagged for stable, and two cleanups.
Signed-off-by: Chris Mason <clm@fb.com>
Pull EDAC updates from Borislav Petkov:
- add KNM support to sb_edac (Piotr Luc)
- add AMD Zen support to amd64_edac (Yazen Ghannam)
- misc small cleanups, improvements and fixes (Colin Ian King, Dave
Hansen, Pan Bian, Thor Thayer, Wei Yongjun, Yanjiang Jin, yours
truly)
* tag 'edac_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (26 commits)
EDAC, amd64: Fix improper return value
EDAC, amd64: Improve amd64-specific printing macros
EDAC, amd64: Autoload amd64_edac_mod on Fam17h systems
EDAC, amd64: Define and register UMC error decode function
EDAC, amd64: Determine EDAC capabilities on Fam17h systems
EDAC, amd64: Determine EDAC MC capabilities on Fam17h
EDAC, amd64: Add Fam17h debug output
EDAC, amd64: Add Fam17h scrubber support
EDAC, mce_amd: Don't report poison bit on Fam15h, bank 4
EDAC, amd64: Read MC registers on AMD Fam17h
EDAC, amd64: Reserve correct PCI devices on AMD Fam17h
EDAC, amd64: Add AMD Fam17h family type and ops
EDAC, amd64: Extend ecc_enabled() to Fam17h
EDAC, amd64: Don't force-enable ECC checking on newer systems
EDAC, amd64: Add Deferred Error type
EDAC, amd64: Rename __log_bus_error() to be more specific
EDAC, amd64: Change target of pci_name from F2 to F3
EDAC, mce_amd: Rename nb_bus_decoder to dram_ecc_decoder
EDAC: Add LRDDR4 DRAM type
EDAC, mpc85xx: Implement remove method for the platform driver
...
Pull thermal management updates from Zhang Rui:
- Thermal core code reorganization and cleanup. Two new files are
created for thermal sysfs I/F code and thermal helper functions
(Eduardo Valentin).
- Sanitize hotplug and locking for x86_pkg_temp driver (Thomas
Gleixner)
- Update MAINTAINER file for pwm-fan driver and Samsung thermal driver
(Lukasz Majewski)
- Fix module auto-load for max77620, tango and db8500 thermal driver
(Javier Martinez Canillas)
- Fix a bug that thermal hwmon sysfs I/F returns wrong critical trip
point temperature value (Krzysztof Kozlowski)
- Add Skylake PCH 100 series support for intel_pch_thermal driver
(OGAWA Hirofumi)
- Small fixes and cleanups for platform thermal drivers (Julia Lawall,
Luis Henriques, Leo Yan, Stephen Boyd, Shawn Lin, Javi Merino and
Lukasz Luba)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (76 commits)
MAINTAINERS: Samsung: Update maintainer for PWM FAN and SAMSUNG THERMAL
thermal/x86 pkg temp: Convert to hotplug state machine
thermal/x86_pkg_temp: Sanitize package management
thermal/x86_pkg_temp: Move work into package struct
thermal/x86_pkg_temp: Move work scheduled flag into package struct
thermal/x86_pkg_temp: Sanitize locking
thermal/x86_pkg_temp: Cleanup code some more
thermal/x86_pkg_temp: Cleanup namespace
thermal/x86_pkg_temp: Get rid of ref counting
thermal/x86_pkg_temp: Sanitize callback (de)initialization
thermal/x86_pkg_temp: Replace open coded cpu search
thermal/x86_pkg_temp: Remove redundant package search
thermal/x86_pkg_temp: Cleanup thermal interrupt handling
thermal: hwmon: Properly report critical temperature in sysfs
devfreq_cooling: pass a pointer to devfreq in the power model callbacks
devfreq_cooling: make the structs devfreq_cooling_xxx visible for all
dt-bindings: rockchip-thermal: fix the misleading description
thermal: rockchip: improve the warning log
thermal: db8500: Fix module autoload
thermal: tango: Fix module autoload
...
Pull clk updates from Stephen Boyd:
"This is a fairly quiet release. We don't have any patches to the core
framework. The only patch that can even be considered "core" adds
another clk_get() variant. The rest of the changes are in drivers for
various SoCs, and we have a few bits for ARM shmobile architecture
code (dts and mach) due to the dependency we're breaking between
shmobile architecture code and its clk driver. Those shmobile bits
have also been pulled into arm-soc tree. Here's the summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that
have subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL
support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: bcm: Fix 'maybe-uninitialized' warning in bcm2835_clock_choose_div_and_prate()
clk: add devm_get_clk_from_child() API
clk: st: clk-flexgen: Unmap region obtained by of_iomap
clk: keystone: pll: Unmap region obtained by of_iomap
clk:mmp:clk-of-mmp2: Free memory and Unmap region obtained by kzalloc and of_iomap
clk:mmp:clk-of-pxa910: Free memory and Unmap region obtained by kzmalloc and of_iomap
clk: mmp: clk-of-pxa1928: Free memory obtained by kzalloc
clk: cdce925: Fix limit check
clk: bcm: Make COMMON_CLK_IPROC into a library
clk: qoriq: added ls1012a clock configuration
clk: ti: dra7: fix "failed to lookup clock node gmac_gmii_ref_clk_div" boot message
clk: bcm: Allow rate change propagation to PLLH_AUX on VEC clock
clk: bcm: Support rate change propagation on bcm2835 clocks
clk: bcm2835: Avoid overwriting the div info when disabling a pll_div clk
clk: ti: omap36xx: Work around sprz319 advisory 2.1
clk: clk-wm831x: fix a logic error
clk: uniphier: add cpufreq data for LD11, LD20 SoCs
clk: uniphier: add CPU-gear change (cpufreq) support
clk: qcom: Put venus core0/1 gdscs to hw control mode
clk: qcom: gdsc: Add support for gdscs with HW control
...
Pull rpmsg updates from Bjorn Andersson:
"Argument validation in public functions, function stubs for
COMPILE_TEST-ing clients, preparation for exposing rpmsg endponts
to user space and minor Qualcomm SMD fixes"
* tag 'rpmsg-v4.10' of git://github.com/andersson/remoteproc:
dt-binding: soc: qcom: smd: Add label property
rpmsg: qcom_smd: Correct return value for O_NONBLOCK
rpmsg: Provide function stubs for API
rpmsg: Handle invalid parameters in public API
rpmsg: Support drivers without primary endpoint
rpmsg: Introduce a driver override mechanism
rpmsg: smd: Reduce restrictions when finding channel
Pull remoteproc updates from Bjorn Andersson:
- introduce remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
- handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
- the debugfs mechanism for starting and stopping remoteproc instances
was replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
- new drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
- finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug
fixes and cleanups
* tag 'rproc-v4.10' of git://github.com/andersson/remoteproc: (49 commits)
remoteproc: qcom_adsp_pil: select qcom_scm
remoteproc: Drop wait in __rproc_boot()
remoteproc/ste: Delete unused driver
remoteproc: Remove "experimental" warning
remoteproc: qcom_adsp_pil: select qcom_scm
dt-binding: soc: qcom: smd: Add label property
remoteproc: qcom: mdt_loader: add include for sizes
remoteproc: Update last rproc_put users to rproc_free
remoteproc: qcom: adsp: Add missing MODULE_DEVICE_TABLE
remoteproc: wcnss-pil: add QCOM_SMD dependency
dmaengine: st_fdma: Revert: "Revert: Update st_fdma to 'depends on REMOTEPROC'"
remoteproc: Add support for xo clock
remoteproc: adsp-pil: fix recursive dependency
remoteproc: Introduce Qualcomm ADSP PIL
dt-binding: remoteproc: Introduce ADSP loader binding
remoteproc: qcom_wcnss: Fix circular module dependency
remoteproc: Merge table_ptr and cached_table pointers
remoteproc: Remove custom vdev handler list
remoteproc: Update max_notifyid as we allocate vrings
remoteproc: Decouple vdev resources and devices
...
Pull MMC updates from Ulf Hansson:
"It's been an busy period for mmc. Quite some changes in the mmc core,
two new mmc host drivers, some existing drivers being extended to
support new IP versions and lots of other updates.
MMC core:
- Delete eMMC packed command support
- Introduce mmc_abort_tuning() to enable eMMC tuning to fail
gracefully
- Introduce mmc_can_retune() to see if a host can be retuned
- Re-work and improve the sequence when sending a CMD6 for mmc
- Enable CDM13 polling when switching to HS and HS DDR mode for mmc
- Relax checking for CMD6 errors after switch to HS200
- Re-factoring the code dealing with the mmc block queue
- Recognize whether the eMMC card supports CMDQ
- Fix 4K native sector check
- Don't power off the card when starting the host
- Increase MMC_IOC_MAX_BYTES to support bigger firmware binaries
- Improve error handling and drop meaningless BUG_ONs()
- Lots of clean-ups and changes to improve the quality of the code
MMC host:
- sdhci: Fix tuning sequence and clean-up the related code
- sdhci: Add support to via DT override broken SDHCI cap register
bits
- sdhci-cadence: Add new driver for Cadence SD4HC SDHCI variant
- sdhci-msm: Update clock management
- sdhci-msm: Add support for eMMC HS400 mode
- sdhci-msm: Deploy runtime/system PM support
- sdhci-iproc: Extend driver support to newer IP versions
- sdhci-pci: Add support for Intel GLK
- sdhci-pci: Add support for Intel NI byt sdio
- sdhci-acpi: Add support for 80860F14 UID 2 SDIO bus
- sdhci: Lots of various small improvements and clean-ups
- tmio: Add support for tuning
- sh_mobile_sdhi: Add support for tuning
- sh_mobile_sdhi: Extend driver to support SDHI IP on R7S72100 SoC
- sh_mobile_sdhi: remove support for sh7372
- davinci: Use mmc_of_parse() to enable generic mmc DT bindings
- meson: Add new driver to support GX platforms
- dw_mmc: Deploy generic runtime/system PM support
- dw_mmc: Lots of various small improvements
As a part of the mmc changes this time, I have also pulled in an
immutable branch/tag (soc-device-match-tag1) hosted by Geert
Uytterhoeven, to share the implementation of the new
soc_device_match() interface. This is needed by these mmc related
changes:
- mmc: sdhci-of-esdhc: Get correct IP version for T4240-R1.0-R2.0
- soc: fsl: add GUTS driver for QorIQ platforms"
* tag 'mmc-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (136 commits)
mmc: sdhci-cadence: add Cadence SD4HC support
mmc: sdhci: export sdhci_execute_tuning()
mmc: sdhci: Tidy tuning loop
mmc: sdhci: Simplify tuning block size logic
mmc: sdhci: Factor out tuning helper functions
mmc: sdhci: Use mmc_abort_tuning()
mmc: mmc: Introduce mmc_abort_tuning()
mmc: sdhci: Always allow tuning to fall back to fixed sampling
mmc: sdhci: Fix tuning reset after exhausting the maximum number of loops
mmc: sdhci: Fix recovery from tuning timeout
Revert "mmc: sdhci: Reset cmd and data circuits after tuning failure"
mmc: mmc: Relax checking for switch errors after HS200 switch
mmc: sdhci-acpi: support 80860F14 UID 2 SDIO bus
mmc: sdhci-of-at91: remove bogus MMC_SDHCI_IO_ACCESSORS select
mmc: sdhci-pci: Use ACPI to get max frequency for Intel NI byt sdio
mmc: sdhci-pci: Add PCI ID for Intel NI byt sdio
mmc: sdhci-s3c: add spin_unlock_irq() before calling clk_round_rate
mmc: dw_mmc: display the clock message only one time when card is polling
mmc: dw_mmc: add the debug message for polling and non-removable
mmc: dw_mmc: check the "present" variable before checking flags
...
Pull regulator updates from Mark Brown:
"A quiet release for the regulator API, conference season must've been
slowing everyone down:
- a new interface allowing drivers to provide an interface for
reading a more detailed description of error conditions which
allows devices using these regulators to build
- ACPI support for the fixed voltage regulator.
- cleanups for the TI TWL drivers to reduce code duplication"
* tag 'regulator-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (24 commits)
regulator: tps65086: Fix 25mV ranges for BUCK regulators 1, 2, and 6
regulator: Fix regulator_get_error_flags() signature mismatch
regulator: core: add newline in debug message
regulator: tps65086: Fix 25mV ranges for BUCK regulators
regulator: core: Correct type of mode in regulator_mode_constrain
regulator: max77620: add documentation for MPOK property
regulator: max77620: add support to configure MPOK
regulator: twl6030: Remove unused fields from struct twlreg_info
regulator: twl: Remove unused fields from struct twlreg_info
regulator: twl: split twl6030 logic into its own file
regulator: twl: kill unused functions
regulator: twl: make driver DT only
regulator: twl-regulator: rework fixed regulator definition
regulator: max77620: remove unused variable
regulator: pwm: Add missing quotes to DT example
regulator: stw481x-vmmc: fix ages old enable error
regulator: gpio: properly check return value of of_get_named_gpio
regulator: lp873x: Add support for populating input supply
regulator: axp20x: Fix axp809 ldo_io registration error on cold boot
regulators: helpers: Fix handling of bypass_val_on in get_bypass_regmap
...
Pull regmap fixlet from Mark Brown:
"The only change for regmap this merge window is a single fix for an
unused variable"
* tag 'regmap-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: cache: Remove unused 'blksize' variable
Shift down default message verbosity, where it does not show
error results in stdout by default. Since that behavior
is the same as giving the --quiet option, this patch removes
--quiet and makes --verbose increasing verbosity.
In other words, this changes verbosity options as below.
ftracetest -q -> ftracetest
ftracetest -> ftracetest -v
ftracetest -v -> ftracetest -v -v (or -vv)
Link: http://lkml.kernel.org/r/148007872763.5917.15256235993753860592.stgit@devbox
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull LED updates from Jacek Anaszewski:
- userspace LED class driver - it can be useful for testing triggers
and can also be used to implement virtual LEDs
- LED class driver for NIC78bx device
- LED core fixes for preventing potential races while setting
brightness when software blinking is enabled
- improvements in LED documentation to mention semantics on changing
brightness while trigger is active
* tag 'leds_for_4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Add ACPI support
leds: netxbig: fix module autoload for OF registration
leds: pca963x: Add ACPI support
leds: leds-cobalt-raq: use builtin_platform_driver
led: core: Fix blink_brightness setting race
led: core: Use atomic bit-field for the blink-flags
leds: Add user LED driver for NIC78bx device
leds: verify vendor and change license in mlxcpld driver
leds: pca963x: enable low-power state
leds: pca9532: Use default trigger value from platform data
leds: pca963x: workaround group blink scaling issue
cleanup LED documentation and make it match reality
leds: lp3952: Export I2C module alias information for module autoload
leds: mc13783: Fix MC13892 keypad led access
ledtrig-cpu.c: fix english
leds/leds-lp5523.txt: make documentation match reality
tools/leds: Add uledmon program for monitoring userspace LEDs
leds: Use macro for max device node name size
leds: Introduce userspace LED class driver
mfd: qcom-pm8xxx: Clean up PM8XXX namespace
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
Commit 4490001029 ("virtio-net: enable
multiqueue by default") blindly set the affinity instead of queues
during probe which can cause a mismatch of #queues between guest and
host. This patch fixes it by setting queues.
Reported-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Fixes: 49000102901 ("virtio-net: enable multiqueue by default")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a buffer is duplicated during MESH packet forwarding,
this patch ensures that the new buffer has enough headroom.
Signed-off-by: Cedric Izoard <cedric.izoard@ceva-dsp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers know nothing about AP_VLAN interfaces, trying to
call drv_set_default_unicast_key() just results in a warning
and no call to the driver. Avoid the warning by not calling the
driver for this on AP_VLAN interfaces.
This means that drivers that somehow need this call for AP mode
will fail to work properly in the presence of VLAN interfaces,
but the current drivers don't seem to use it, and mac80211 will
select and indicate the key - so drivers should be OK now.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If link training fails, then we need to fallback to lower
link rate first and if link training fails at RBR, then
fallback to lower lane count.
This function finds the next lower link rate/lane count
value after link training failure and limits the max
link_rate and lane_count values to these fallback values.
v7:
* Remove unnecessary intializations and remove redundant
call to intel_dp_common_rates (Jani Nikula)
v6:
* Cap the max link rate and lane count to the max
values obtained during fallback link training (Daniel Vetter)
v5:
* Start the fallback at the lane count value passed not
the max lane count (Jani Nikula)
v4:
* Remove the redundant variable link_train_failed
v3:
* Remove fallback_link_rate_index variable, just obtain
that using the helper intel_dp_link_rate_index (Jani Nikula)
v2:
Squash the patch that returns the link rate index (Jani Nikula)
Acked-by: Tony Cheng <tony.cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481252712-12925-1-git-send-email-manasi.d.navare@intel.com
This test script try to do whitebox testing for gpio subsystem(based on
gpiolib). It manipulate gpio device through chardev or sysfs and check
the result from debugfs. This script test gpio-mockup through chardev by
default. User could test other gpio chip by passing the module name.
Some of the testcases are turned off by default to avoid the conflicting
with gpiochip in system.
In details, it test the following things:
1. Test direction and output value for valid pin.
2. Test dynamic allocation of gpio base.
3. Add single, multi gpiochip to do overlap check.
Run "tools/testing/selftests/gpio/gpio-mockup.sh -h" for usage.
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
- Again move the information relevant for driver writers next to the
callbacks.
- Put the overview and userspace interface documentation into a DOC:
section within the code.
- Remove the text that mmap needs to be coherent - since the
DMA_BUF_IOCTL_SYNC landed that's no longer the case. But keep the text
that for pte zapping exporters need to adjust the address space.
- Add a FIXME that kmap and the new begin/end stuff used by the SYNC
ioctl don't really mix correctly. That's something I just realized
while doing this doc rework.
- Augment function and structure docs like usual.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
[sumits: fix cosmetic issues]
Link: http://patchwork.freedesktop.org/patch/msgid/20161209185309.1682-5-daniel.vetter@ffwll.ch
fsnotify_unmount_inodes() plays complex tricks to pin next inode in the
sb->s_inodes list when iterating over all inodes. Furthermore the code has a
bug that if the current inode is the last on i_sb_list that does not have e.g.
I_FREEING set, then we leave next_i pointing to inode which may get removed
from the i_sb_list once we drop s_inode_list_lock thus resulting in
use-after-free issues (usually manifesting as infinite looping in
fsnotify_unmount_inodes()).
Fix the problem by keeping current inode pinned somewhat longer. Then we can
make the code much simpler and standard.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
- Put the initial overview for dma-buf into dma-buf.rst.
- Put all the comments about detailed semantics into the right
kernel-doc comment for functions or ops structure member.
- To allow that detail, switch the reworked kerneldoc to inline style
for dma_buf_ops.
- Tie everything together into a much more streamlined overview
comment, relying on the hyperlinks for all the details.
- Also sprinkle some links into the kerneldoc for dma_buf and
dma_buf_attachment to tie it all together.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161209185309.1682-4-daniel.vetter@ffwll.ch
Backmerge the docs-next branch from Jon into drm-misc so that we can
apply the dma-buf documentation cleanup patches. Git found a conflict
where there was none because both drm-misc and docs had identical
patches to clean up file rename issues in the rst include directives.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The logical package management has several issues:
- The APIC ids provided by ACPI are not required to be the same as the
initial APIC id which can be retrieved by CPUID. The APIC ids provided
by ACPI are those which are written by the BIOS into the APIC. The
initial id is set by hardware and can not be changed. The hardware
provided ids contain the real hardware package information.
Especially AMD sets the effective APIC id different from the hardware id
as they need to reserve space for the IOAPIC ids starting at id 0.
As a consequence those machines trigger the currently active firmware
bug printouts in dmesg, These are obviously wrong.
- Virtual machines have their own interesting of enumerating APICs and
packages which are not reliably covered by the current implementation.
The sizing of the mapping array has been tweaked to be generously large to
handle systems which provide a wrong core count when HT is disabled so the
whole magic which checks for space in the physical hotplug case is not
needed anymore.
Simplify the whole machinery and do the mapping when the CPU starts and the
CPUID derived physical package information is available. This solves the
observed problems on AMD machines and works for the virtualization issues
as well.
Remove the extra call from XEN cpu bringup code as it is not longer
required.
Fixes: d49597fd3b ("x86/cpu: Deal with broken firmware (VMWare/XEN)")
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: xen-devel <xen-devel@lists.xen.org>
Cc: Charles (Chas) Williams <ciwillia@brocade.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alok Kataria <akataria@vmware.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1612121102260.3429@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When compiling with 'W=1' warnings such as the following occur all over
the place:
./include/linux/pfn.h:21:22: warning: comparison of unsigned expression
>= 0 is always true [-Wtype-limits]
which is due to ARCH_PFN_OFFSET being 0 by default
(if CONFIG_NIOS2_MEM_BASE is not changed in the Kconfig). Fix these
warnings by making pfn_valid a static inline function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
