Update FW version readback. IPC_GLB_GET_FW_VERSION reads back
the ABI version whilst the release version is in the mailbox.
Update to use mailbox version for info logging.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sst-haswell-dsp.c is an ACPI independent file, this patch removes
ACPI header files for it.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This interface will be used by subsequent patches to set/get parameters from DSP
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP returns error codes for IPC return so add them in driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the shim registers start and end can be useful while parsing the shim addresses,
so add these
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge D-SRAM0 D-SRAM1 D-SRAM2 to D-SRAM, for wild cat point ADSP mem regions.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dummy read after each block enable, to workaround
SRAM write missing bytes issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This change removes unsupported formats from System,
Capture and Loopback FE DAIs.
Also it fixes S24_LE support on all DAIs.
While at this fix 24 bit flag for BYT as well.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Kernel should not enable/disable speakers and digital microphone whenever
jack is inserted/removed. This is more use-case than kernel specific
decision. For instance one may want to play VoIP ring tones using both
speakers and headphone but play music only from one of them.
Because of above reason remove "Ext Spk" and "Int Mic" update when jack
state is changed. Also this update was illogical anyway: "Ext Spk" was
enabled when jack was inserted and disabled when jack was removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It turned out there is no need to enable microphone detection in MAX98090
codec. Headset microphone is anyway detected by a GPIO signal from another
chip and headset button presses cannot be detected either because a signal
needed for it is not connected.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass actual jack type bitmask to snd_soc_jack_new() in order to report
also microphone detections and not only headphone. While at it change also
jack name and pass also SND_JACK_LINEOUT type.
Reported-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mic detect GPIO is active low when headset microphone is detected. Found
both by debugging and checking the schematics.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move "MICBIAS" as a supply widget to "Headset Mic" instead of keeping it
between input pin "IN34" and "Headset Mic".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As added in previosu patch along with stream to piep conversion si required for
compressed audio too
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merrifield DSP used various pipelines to identify the streams and processing
modules. Add these defination in the pcm driver and also add a table for device
entries to firmware pipeline id conversion
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tis will be used to add table based support for pcm front ends in subsequent
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be used to update current driver as well as in support for the mrfld
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now the DSP is capable of reporting the delay, report it to upper layers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The argument was called mad_substream which is no longer apt as older driver
is not used anymore so rename as arg
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps us to handle pcm and compress ops seperately and per dai
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Connect "Headset Mic" to "MICBIAS1" supply widget of RT5640 in order to
enable bias voltage for headset microphones.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP initialization complete message IPC_IA_FW_INIT_CMPLT is a large message
carrying firmware details in mailbox. Read and show those details during
init in order to be able to get that information to QA reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use card PM ops from ASoC core instead of defining custom PM ops here since
we are calling anyway common suspend/resume callbacks.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify byt-rt5640.c and haswell.c machine drivers by using
devm_snd_soc_register_card(). Remove also needless dev_set_drvdata()
from byt_rt5640_probe() since snd_soc_register_card() does it too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Stored DSP DMA pointer must be cleared before starting the stream since
PCM pointer callback sst_byt_pcm_pointer() can be called before pointer is
updated. In that case last position of previous stream was wronly returned.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Baytrail and Haswell SST IPC don't stop the kernel thread in error and
cleanup path thus leaving orphan kernel thread behind in such a case.
Also while at it, fix one error path in sst-haswell-ipc.c that doesn't free
hsw->msg.
[Jarkko: I edited the commit log a little]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases the pcm stream is closed while context has been
scheduled to be restored, causing a null pointer deref panic.
Cancel work to ensure stream does not get freed while work is
still active/pending.
Also, restoring the pcm context can be safely skipped after the
stream has been stopped. Check if pcm stream is still running
before restoring stream context to help pending work finish
more quickly in stream close path.
Signed-off-by: Kevin Strasser <kevin.strasser@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core marks widgets as connected by default when they are
initialized in snd_soc_dapm_new_control() so there is no need to call
snd_soc_dapm_enable_pin() from machine driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core takes care of calling snd_soc_dapm_sync() at the end
snd_soc_instantiate_card() so there is no need to call it from machine
driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 0cac6fc3eb.
This comiit was dropped from rev2 and would not be required as it renames the
platform ops as well which is not required.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I managed to drop a change to stream ID setting from commit 49fee17816
("ASoC: Intel: Only export one Baytrail DAI") leading to non-working
simultaneous capture-playback since after one DAI conversion
rtd->cpu_dai->id + 1 will be the same for both playback and capture.
Use substream->stream + 1 like it was in original Liam's patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't need more than one DAI for Baytrail SST. Usage becomes also more
straightforward by grouping playback and capture streams under the same PCM
device.
[Jarkko: I made Liam's sst-baytrail-pcm.c change a few lines smaller and
squashed together with my byt-rt5640.c change]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Prepare for single Baytrail DAI playback/capture link by accessing PCM data
using stream ID instead of rtd->dev. Now rtd->dev is unique for playback
and capture since they are exported as separate DAIs but not once converted
to single DAI.
[Jarkko: Separated from another commit with updated commit log]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
