When HS extmute is enabled without custom GPIO we should configure the mux
to allow the pin to be used as extmute signal.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage update the machine drivers at the same time using
twl4030: omap3pandora, sdp3430 and zoom2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to be able to use the Voice port of twl4030 three bits need to be
handled in VOICE_IF register:
VIF_EN: to enable the voice port (needed for both playback and capture)
VIF_DIN_EN: Need to be enabled for playback only (input to the codec)
VIF_DOUT_EN: Need to be enabled for capture only (output from codec)
Use DAPM_SUPPLY for the VIF_EN bit and add DAPM_AIF_IO/OUT widget to handle
the playback/capture bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor set_pll code to avoid the following warnings:
sound/soc/codecs/wm8985.c:852:50: warning: 'pll_div.k' may be used uninitialized in this function
sound/soc/codecs/wm8985.c:849:9: warning: 'pll_div.n' may be used uninitialized in this function
sound/soc/codecs/wm8985.c:848:23: warning: 'pll_div.div2' may be used uninitialized in this function
Do the same as in commit 86ce6c9a (ASoC: WM8804: Refactor set_pll code to avoid
GCC warnings).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from wm8350. Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of no-match, return -EINVAL instead of 0.
Since we assign i to ret in the for loop, ret always less than
ARRAY_SIZE(clk_map_table). Thus remove the boundary checking for ret.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor set_pll code to avoid the following warnings:
sound/soc/codecs/wm8983.c:873:40: warning: 'pll_div.k' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm8983.c:870:9: warning: 'pll_div.n' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm8983.c:869:23: warning: 'pll_div.div2' may be used uninitialized in this function [-Wuninitialized]
Do the same as in commit 86ce6c9a (ASoC: WM8804: Refactor set_pll code to avoid
GCC warnings).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4271 requires its LRCLK and MCLK to be stable before its RESET
line is de-asserted. That also means that clocks cannot be changed
without putting the chip back into hardware reset, which also requires
a complete re-initialization of all registers.
One (undocumented) workaround is to assert and de-assert the PDN bit
in the MODE2 register.
This patch adds a new flag to both the DT bindings as well as to the
platform data to enable that workaround.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we are now using the clock API integration to manage MCLK we can now
use clk_get_rate() to determine if we need to divide MCLK without relying
on platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Request MCLK as a clock and then enable it when carrying out a state
transtion and while ANC is active, minimising system power consumption
in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the FLL is being shut down we will exit early so there is no need to
check here and in fact we're checking the wrong thing anyway.
Reported-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.
From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."
So change the default microphone gain as well.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the mask and mode settings are wrong in current code.
According to the datasheet:
S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
serial interface protocol format:
000: left Justified
001: I2S (default)
010: right justified
100: PCM no delay
101: PCM delay
111: DSP
Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
