When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire V5 with the ALC282 codec is given the wrong value for the
0x19 PIN by the laptop's BIOS. Overriding it with the correct value
adds support for the headset microphone which would not otherwise be
visible in the system.
The fix is based on commit 7819717b11 with a similar quirk for Acer
Aspire with the ALC269 codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Mateusz Sylwestrzak <matisec7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull sound fixes from Takashi Iwai:
"There are two small fixes for HD-audio and USB LINE6, and the rest are
a few new quirks and device ID addition that are good enough to get
into 4.2"
* tag 'sound-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable HP amp and mute LED on HP Folio 9480m [v3]
ALSA: line6: Fix -EBUSY error during active monitoring
ALSA: hda - Fix a wrong busy check in alt PCM open
ALSA: hda - add codec ID for Broxton display audio codec
ALSA: usb-audio: Add MIDI support for Steinberg MI2/MI4
In kstrdup we should return -ENOMEM when it reports an
memory allocation failure, while the -ENODEV is referred
to a failure in finding the cpu node in the device tree.
Signed-off-by: Heloise NH <kernelpatch_update@163.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop needs GPIO4 pulled high to enable the headphone amplifier,
and has a mute LED on GPIO3. I modelled the patch on the existing
GPIO4 code which pulls the line low for the same purpose; this time,
the HP amp line is pulled high.
v2: Disable the headphone amplifier when no headphone is connected.
Don't disable power savings to preserve the LED state.
v3: Remove headset-specific hooks and code; this is just a headphone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the alt PCM open callback returns -EBUSY when an
independent HP is turned off, supposing that it conflicts with the
main PCM. However, obviously, this check is wrong when the
independent HP itself isn't enabled but the alt PCM was explicitly
created via alc_dac_nid by a codec driver.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x8086280a) and module alias for Broxton
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull sound fixes from Takashi Iwai:
"Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups"
* tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Fix uninintialized error return
ALSA: hda: Delete an unnecessary check before the function call "snd_info_free_entry"
ALSA: hda - Add a fixup for Dell E7450
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780
ALSA: hda - Add headset support to Acer Aspire V5
ALSA: hda - restore the MIC FIXUP for some Dell machines
ALSA: jack: Fix endless loop at unique index detection
ALSA: hda - set proper caps for newer AMD hda audio in KB/KV
ALSA: hda - Disable widget power-save for VIA codecs
ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
The snd_info_free_entry() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
The fix is to ignore the non-HP sequencer checks.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget power-save that was enabled in 4.1 kernel seems resulting
in the silent output on VIA codecs by some reason. Some widgets get
wrong power states.
As a quick fix, turn this flag off while keeping power_down_unused
flag. This will bring back to the state of 4.0.x.
Fixes: 688b12cc3c ('ALSA: hda - Use the new power control for VIA codecs')
Reported-and-tested-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since this is common option for HDA driver to specfiy pre-allocated
buffer, we should make this option availble to all HDA driver by
moving this to HDA core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SND_HDA_I915=n, we get a compile warning:
sound/pci/hda/hda_intel.c: In function ‘azx_probe_continue’:
sound/pci/hda/hda_intel.c:1882:2: warning: label ‘skip_i915’ defined but not used [-Wunused-label]
Fix it by putting again ifdef to it. Sigh.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new Dell XPS13 also requires the similar quirk for fixing the
noisy outputs. (But, as the codec was changed, now the fixup for
Latitude is used instead.)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99851
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We still got a report that the audio crackles and noises occur with
the recent 4.1 kernels on Dell machines. These machines seem to need
similar workarounds that have been applied to the recent Dell XPS 13
models. Since the codec of these machines (Dell Latitute E7240 and
E7440) is different from XPS 13's one, we need a new fixup entry.
Also, it was confirmed that the previous workaround to disable the
widget power-save (commit [219f47e4f9: ALSA: hda - Disable widget
power-saving for ALC292 & co]) is no longer needed after this fix.
So, this patch includes the partial revert of the commit, too.
Reported-and-tested-by: Mihai Donțu <mihai.dontu@gmail.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a HP Envy TouchSmart laptop, there are 2 speakers (main speaker
and subwoofer speaker), 1 headphone and 2 DACs, without this fixup,
the headphone will be assigned to a DAC and the 2 speakers will be
assigned to another DAC, this assignment makes the surround-2.1
channels invalid.
To fix it, here using a DAC/pin preference map to bind the main
speaker to 1 DAC and the subwoofer speaker will be assigned to another
DAC.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous patch tried to continue the probe if i915 binding fails.
For for simplicity reason, we haven't implemented abort even for
controller chips that are dedicated for HDMI/DP on HSW and BDW.
However, Mengdong suggested that this can be dangerous; BIOS may
disable gfx power well although the PCI entry for HD-audio is left,
and this may result in the unexpected behavior, kernel errors, etc.
For avoiding this situation, abort the probe at i915 binding failure
only for HSW/BDW chips selectively. For other chips, it still
continues.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another regression by the transition to regmap cache; for better
usability, we had the fake mute control using the zero amp value for
Conexant codecs, and this was forgotten in the new hda core code.
Since the bits 4-7 are unused for the amp registers (as we follow the
syntax of AMP_GET verb), the bit 4 is now used to indicate the fake
mute. For setting this flag, snd_hda_codec_amp_update() becomes a
function from a simple macro. The bonus is that it gained a proper
function description.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges and resolves the non-trivial conflicts with the recent fix
for hda-i915 binding fallback.
Conflicts:
sound/pci/hda/hda_intel.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd-hda-intel driver aborts the probing of Intel HD-audio
controller with i915 power well management when binding with i915
driver via hda_i915_init() fails. This is no big problem for Haswell
and Broadwell where the HD-audio controllers are dedicated to
HDMI/DP, thus i915 link is mandatory. However, Skylake, Baytrail and
Braswell have only one controller and both HDMI/DP and analog codecs
share the same bus. Thus, even if HDMI/DP isn't usable, we should
keep the controller working for other codecs.
For fixing this, this patch simply allows continuing the probing even
if hda_i915_init() call fails. This may leave stale sound components
for HDMI/DP devices that are unbound with graphics. We could abort
the probing selectively, but from the code simplicity POV, it's better
to continue in all cases.
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable runtime PM of the HDMI audio codec on the latest Intel platforms.
So the HD-A controller or HDMI codec can suspend when idle timeout by
default and release the GFX power well.
The patch influences HSW/BDW/BYT/BSW/SKL. Eariler platforms and third
party analog codecs will not be influenced.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new regmap code seems to cache this, which isn't helpful
for the hotplug dock situation where this gets updated.
Use the uncached query for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the controller flag 'need_i915_power' is
not set to release the display power after probe, and the codec flag
'link_power_control' is set to request/release the display power via
bus link_power ops.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT202x codecs seem requiring some delay after the resume D0 power
transition for making the jack detection working again. Without the
delay soon after D0, the jack is always detected as unplugged.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98921
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... so that the parser code can overwrite some optional ops. For
Realtek and others, it can be set solely in the spec allocator, so it
results in a good code cleanup, too.
With this change, we can finally remove the local stream_pm setup and
rely on the generic parser's automatic setting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [49fb189725: ALSA: hda - Set stream_pm ops automatically
by generic parser] resulted in regressions on some Realtek and VIA
codecs because these drivers set patch_ops after calling the generic
parser, thus stream_pm got cleared to NULL again. I haven't noticed
since I tested with IDT codec.
Restore (partial revert) the stream_pm ops for them to fix the
regression.
Fixes: 49fb189725 ('ALSA: hda - Set stream_pm ops automatically by generic parser')
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When headphone mic boost is above zero, some 10 - 20 second delay
might occur before the headphone mic is operational.
Therefore disable the headphone mic boost control (recording gain is
sufficient even without it).
(Note: this patch is not about the headset mic, it's about the less
common mic-in only mode.)
BugLink: https://bugs.launchpad.net/bugs/1454235
Suggested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We may disable proc fs only for sound part, to reduce ALSA
memory footprint. So add CONFIG_SND_PROC_FS and replace the
old CONFIG_PROC_FSs in alsa code.
With sound proc fs disabled, we can save about 9KB memory
size on X86_64 platform.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report that 4.1-rc causes noises on a Dell
laptop. Similar like Realtek codec, this seems also triggered by the
recent power_save_node feature. As this kind of issue is quite hard
to debug without actual hardware, disable the power_save_node flag for
this codec as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows user to test power_save_node feature via sysfs or patch
firmware even on the codecs that don't specify it. It'll also save a
few lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
