bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to commit f8ffad69c9 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.
Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Fixes the following sparse warning:
net/ceph/mon_client.c:577:6: warning:
symbol 'cancel_generic_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324 ('libceph: support for sending notifies')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Passing nsproxy into sysctl_table_root.lookup was a premature
optimization in attempt to avoid depending on current. The
directory /proc/self/sys has not appeared and if and when
it does this code will need to be reviewed closely and reworked
anyway. So remove the premature optimization.
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Do not drop packet when CSeq is 0 as 0 is also a valid value for CSeq.
simple_strtoul() will return 0 either when all digits are 0
or if there are no digits at all. Therefore when simple_strtoul()
returns 0 we check if first character is digit 0 or not.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If we find a matching element that is inactive with no descendants, we
jump to the found label, then crash because of nul-dereference on the
left branch.
Fix this by checking that the element is active and not an interval end
and skipping the logic that only applies to the tree iteration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Anders K. Pedersen <akp@akp.dk>
Commit 96d1327ac2 ("netfilter: h323: Use mod_timer instead of
set_expect_timeout") just simplify the source codes
if (!del_timer(&exp->timeout))
return 0;
add_timer(&exp->timeout);
to mod_timer(&exp->timeout, jiffies + info->timeout * HZ);
This is not correct, and introduce a race codition:
CPU0 CPU1
- timer expire
process_rcf expectation_timed_out
lock(exp_lock) -
find_exp waiting exp_lock...
re-activate timer!! waiting exp_lock...
unlock(exp_lock) lock(exp_lock)
- unlink expect
- free(expect)
- unlock(exp_lock)
So when the timer expires again, we will access the memory that
was already freed.
Replace mod_timer with mod_timer_pending here to fix this problem.
Fixes: 96d1327ac2 ("netfilter: h323: Use mod_timer instead of set_expect_timeout")
Cc: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit 3d5fdff46c.
Ben Hutchings pointed out that the commit isn't safe since it assumes
that the structure used by the driver is iw_point, when in fact there's
no way to know about that.
Fortunately, the only driver in the tree that ever runs this code path
is the wilc1000 staging driver, so it doesn't really matter.
Clearly I should have investigated this better before applying, sorry.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [though I guess it doesn't matter much]
Fixes: 3d5fdff46c ("wext: Fix 32 bit iwpriv compatibility issue with 64 bit Kernel")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg says:
====================
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.
Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released. The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb. ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.
To this end, the following changes are made:
(1) kernel_rxrpc_data_consumed() is added. This should be called whenever
an skb is emptied so as to crank the ACK and call states. This does
not release the skb, however. kernel_rxrpc_free_skb() must now be
called to achieve that. These together replace
rxrpc_kernel_data_delivered().
(2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().
This makes afs_deliver_to_call() easier to work as the skb can simply
be discarded unconditionally here without trying to work out what the
return value of the ->deliver() function means.
The ->deliver() functions can, via afs_data_complete(),
afs_transfer_reply() and afs_extract_data() mark that an skb has been
consumed (thereby cranking the state) without the need to
conditionally free the skb to make sure the state is correct on an
incoming call for when the call processor tries to send the reply.
(3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
has finished with a packet and MSG_PEEK isn't set.
(4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().
Because of this, we no longer need to clear the destructor and put the
call before we free the skb in cases where we don't want the ACK/call
state to be cranked.
(5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
the delivery function already), and the caller is now responsible for
producing an abort if that was the last packet.
(6) There are many bits of unmarshalling code where:
ret = afs_extract_data(call, skb, last, ...);
switch (ret) {
case 0: break;
case -EAGAIN: return 0;
default: return ret;
}
is to be found. As -EAGAIN can now be passed back to the caller, we
now just return if ret < 0:
ret = afs_extract_data(call, skb, last, ...);
if (ret < 0)
return ret;
(7) Checks for trailing data and empty final data packets has been
consolidated as afs_data_complete(). So:
if (skb->len > 0)
return -EBADMSG;
if (!last)
return 0;
becomes:
ret = afs_data_complete(call, skb, last);
if (ret < 0)
return ret;
(8) afs_transfer_reply() now checks the amount of data it has against the
amount of data desired and the amount of data in the skb and returns
an error to induce an abort if we don't get exactly what we want.
Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:
general protection fault: 0000 [#1] SMP
Modules linked in: kafs(E) af_rxrpc(E) [last unloaded: af_rxrpc]
CPU: 0 PID: 1305 Comm: kworker/u8:3 Tainted: G E 4.7.0-fsdevel+ #1303
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: kafsd afs_async_workfn [kafs]
task: ffff88040be041c0 ti: ffff88040c070000 task.ti: ffff88040c070000
RIP: 0010:[<ffffffff8108fd3c>] [<ffffffff8108fd3c>] __lock_acquire+0xcf/0x15a1
RSP: 0018:ffff88040c073bc0 EFLAGS: 00010002
RAX: 6b6b6b6b6b6b6b6b RBX: 0000000000000000 RCX: ffff88040d29a710
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88040d29a710
RBP: ffff88040c073c70 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff88040be041c0 R15: ffffffff814c928f
FS: 0000000000000000(0000) GS:ffff88041fa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4595f4750 CR3: 0000000001c14000 CR4: 00000000001406f0
Stack:
0000000000000006 000000000be04930 0000000000000000 ffff880400000000
ffff880400000000 ffffffff8108f847 ffff88040be041c0 ffffffff81050446
ffff8803fc08a920 ffff8803fc08a958 ffff88040be041c0 ffff88040c073c38
Call Trace:
[<ffffffff8108f847>] ? mark_held_locks+0x5e/0x74
[<ffffffff81050446>] ? __local_bh_enable_ip+0x9b/0xa1
[<ffffffff8108f9ca>] ? trace_hardirqs_on_caller+0x16d/0x189
[<ffffffff810915f4>] lock_acquire+0x122/0x1b6
[<ffffffff810915f4>] ? lock_acquire+0x122/0x1b6
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff81609dbf>] _raw_spin_lock_irqsave+0x35/0x49
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff814c928f>] skb_dequeue+0x18/0x61
[<ffffffffa009aa92>] afs_deliver_to_call+0x344/0x39d [kafs]
[<ffffffffa009ab37>] afs_process_async_call+0x4c/0xd5 [kafs]
[<ffffffffa0099e9c>] afs_async_workfn+0xe/0x10 [kafs]
[<ffffffff81063a3a>] process_one_work+0x29d/0x57c
[<ffffffff81064ac2>] worker_thread+0x24a/0x385
[<ffffffff81064878>] ? rescuer_thread+0x2d0/0x2d0
[<ffffffff810696f5>] kthread+0xf3/0xfb
[<ffffffff8160a6ff>] ret_from_fork+0x1f/0x40
[<ffffffff81069602>] ? kthread_create_on_node+0x1cf/0x1cf
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device->ndo_set_rx_headroom (introduced in
871b642ade) says
"Setting a negtaive value reset the rx headroom
to the default value".
It seems that the OVS implementation in
3a927bc7cf overlooked this and sets
dev->needed_headroom unconditionally.
This doesn't have an immediate effect, but can mess up later
LL_RESERVED_SPACE calculations, such as done in
net/ipv6/mcast.c:mld_newpack. For reference, this issue was found
from a skb_panic raised there after the length calculations had given
the wrong result.
Note the other current users of this interface
(drivers/net/tun.c:tun_set_headroom and
drivers/net/veth.c:veth_set_rx_headroom) are both checking this
correctly thus need no modification.
Thanks to Ben for some pointers from the crash dumps!
Cc: Benjamin Poirier <bpoirier@suse.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1361414
Signed-off-by: Ian Wienand <iwienand@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to miss a lease period renewal due to the TCP connection
failing to reconnect in a timely fashion. To ensure this doesn't happen,
cap the reconnection timer so that we retry the connection attempt
at least every 1/2 lease period.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When the connect attempt fails and backs off, we should start the clock
at the last connection attempt, not time at which we queue up the
reconnect job.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If the net.ipv6.conf.*.use_temp_addr sysctl is set to '2',
then TCP connections over IPv6 will prefer a 'private' source
address.
These eventually expire and become invalid, typically after a week,
but the time is configurable.
When the local address becomes invalid the client will not be able to
receive replies from the server. Eventually the connection will timeout
or break and a new connection will be established, but this can take
half an hour (typically TCP connection break time).
RFC 4941, which describes private IPv6 addresses, acknowledges that some
applications might not work well with them and that the application may
explicitly a request non-temporary (i.e. "public") address.
I believe this is correct for SUNRPC clients. Without this change, a
client will occasionally experience a long delay if private addresses
have been enabled.
The privacy offered by private addresses is of little value for an NFS
server which requires client authentication.
For NFSv3 this will often not be a problem because idle connections are
closed after 5 minutes. For NFSv4 connections never go idle due to the
period RENEW (or equivalent) request.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
It's possible to have simultaneous upcalls for the same UIDs but
different GSS service. In that case, we need to allow for the
upcall to gssd to proceed so that not the same context is used
by two different GSS services. Some servers lock the use of context
to the GSS service.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, NL80211_MESHCONF_HT_OPMODE validation rejected correct
flag combinations, e.g. IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED |
IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT.
Doing just a range-check allows setting flags that don't exist (0x8)
and invalid flag combinations.
Implements some checks based on IEEE 802.11 2012 8.4.2.59 "HT
Operation element".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword commit message, simplify a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull nfsd updates from Bruce Fields:
"Highlights:
- Trond made a change to the server's tcp logic that allows a fast
client to better take advantage of high bandwidth networks, but may
increase the risk that a single client could starve other clients;
a new sunrpc.svc_rpc_per_connection_limit parameter should help
mitigate this in the (hopefully unlikely) event this becomes a
problem in practice.
- Tom Haynes added a minimal flex-layout pnfs server, which is of no
use in production for now--don't build it unless you're doing
client testing or further server development"
* tag 'nfsd-4.8' of git://linux-nfs.org/~bfields/linux: (32 commits)
nfsd: remove some dead code in nfsd_create_locked()
nfsd: drop unnecessary MAY_EXEC check from create
nfsd: clean up bad-type check in nfsd_create_locked
nfsd: remove unnecessary positive-dentry check
nfsd: reorganize nfsd_create
nfsd: check d_can_lookup in fh_verify of directories
nfsd: remove redundant zero-length check from create
nfsd: Make creates return EEXIST instead of EACCES
SUNRPC: Detect immediate closure of accepted sockets
SUNRPC: accept() may return sockets that are still in SYN_RECV
nfsd: allow nfsd to advertise multiple layout types
nfsd: Close race between nfsd4_release_lockowner and nfsd4_lock
nfsd/blocklayout: Make sure calculate signature/designator length aligned
xfs: abstract block export operations from nfsd layouts
SUNRPC: Remove unused callback xpo_adjust_wspace()
SUNRPC: Change TCP socket space reservation
SUNRPC: Add a server side per-connection limit
SUNRPC: Micro optimisation for svc_data_ready
SUNRPC: Call the default socket callbacks instead of open coding
SUNRPC: lock the socket while detaching it
...
ovs_ct_find_existing() issues a warning if an existing conntrack entry
classified as IP_CT_NEW is found, with the premise that this should
not happen. However, a newly confirmed, non-expected conntrack entry
remains IP_CT_NEW as long as no reply direction traffic is seen. This
has resulted into somewhat confusing kernel log messages. This patch
removes this check and warning.
Fixes: 289f2253 ("openvswitch: Find existing conntrack entry after upcall.")
Suggested-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
Ensure that we don't forget to set up the disconnection timer for the
case when a connect request is fulfilled after the RPC request that
initiated it has timed out or been interrupted.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The logic was inverted here, set the bit if frames are pending.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The switch on chandef->width is missing a break on the
NL8211_CHAN_WIDTH_80P80 case; currently we get a WARN_ON when
center_freq2 is non-zero because of the missing break.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VM sockets virtio transport implementation. This driver runs in the
guest.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This module contains the common code and header files for the following
virtio_transporto and vhost_vsock kernel modules.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio transport will implement graceful shutdown and the related
SO_LINGER socket option. This requires orphaning the sock but keeping
it in the table of connections after .release().
This patch adds the vsock_remove_sock() function and leaves it up to the
transport when to remove the sock.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
struct vsock_transport contains function pointers called by AF_VSOCK
core code. The transport may want its own transport-specific function
pointers and they can be added after struct vsock_transport.
Allow the transport to fetch vsock_transport. It can downcast it to
access transport-specific function pointers.
The virtio transport will use this.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This modification is useful for debugging issues that happen while
the socket is being initialised.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We're seeing traces of the following form:
[10952.396347] svc: transport ffff88042ba4a 000 dequeued, inuse=2
[10952.396351] svc: tcp_accept ffff88042ba4 a000 sock ffff88042a6e4c80
[10952.396362] nfsd: connect from 10.2.6.1, port=187
[10952.396364] svc: svc_setup_socket ffff8800b99bcf00
[10952.396368] setting up TCP socket for reading
[10952.396370] svc: svc_setup_socket created ffff8803eb10a000 (inet ffff88042b75b800)
[10952.396373] svc: transport ffff8803eb10a000 put into queue
[10952.396375] svc: transport ffff88042ba4a000 put into queue
[10952.396377] svc: server ffff8800bb0ec000 waiting for data (to = 3600000)
[10952.396380] svc: transport ffff8803eb10a000 dequeued, inuse=2
[10952.396381] svc_recv: found XPT_CLOSE
[10952.396397] svc: svc_delete_xprt(ffff8803eb10a000)
[10952.396398] svc: svc_tcp_sock_detach(ffff8803eb10a000)
[10952.396399] svc: svc_sock_detach(ffff8803eb10a000)
[10952.396412] svc: svc_sock_free(ffff8803eb10a000)
i.e. an immediate close of the socket after initialisation.
The culprit appears to be the test at the end of svc_tcp_init, which
checks if the newly created socket is in the TCP_ESTABLISHED state,
and immediately closes it if not. The evidence appears to suggest that
the socket might still be in the SYN_RECV state at this time.
The fix is to check for both states, and then to add a check in
svc_tcp_state_change() to ensure we don't close the socket when
it transitions into TCP_ESTABLISHED.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If the connect attempt immediately fails with an EADDRNOTAVAIL error, then
that means our choice of source port number was bad.
This error is expected when we set the SO_REUSEPORT socket option and we
have 2 sockets sharing the same source and destination address and port
combinations.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 402e23b4ed ("SUNRPC: Fix stupid typo in xs_sock_set_reuseport")
Cc: stable@vger.kernel.org # v4.0+
Commit 141ddefce7 ("sctp: change sk state to CLOSED instead of
CLOSING in sctp_sock_migrate") changed sk state to CLOSED if the
assoc is closed when sctp_accept clones a new sk.
If there is still data in sk receive queue, users will not be able
to read it any more, as sctp_recvmsg returns directly if sk state
is CLOSED.
This patch is to add CLOSED state check in sctp_recvmsg to allow
reading data from TCP-style sk with CLOSED state as what TCP does.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, once sctp received SHUTDOWN or shutdown with RD,
sk->sk_shutdown would be set with RCV_SHUTDOWN, and all events would
be dropped in sctp_ulpq_tail_event(). It would cause:
1. some notifications couldn't be received by users. like
SCTP_SHUTDOWN_COMP generated by sctp_sf_do_4_C().
2. sctp would also never trigger sk_data_ready when the association
was closed, making it harder to identify the end of the association
by calling recvmsg() and getting an EOF. It was not convenient for
kernel users.
The check here should be stopping delivering DATA chunks after receiving
SHUTDOWN, and stopping delivering ANY chunks after sctp_close().
So this patch is to allow notifications to enqueue into receive queue
even if sk->sk_shutdown is set to RCV_SHUTDOWN in sctp_ulpq_tail_event,
but if sk->sk_shutdown == RCV_SHUTDOWN | SEND_SHUTDOWN, it drops all
events.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp needs to queue auth chunk back when we know that we are going
to generate another segment. But commit f1533cce60 ("sctp: fix
panic when sending auth chunks") requeues the last chunk processed
which is probably not the auth chunk.
It causes panic when calculating the MAC in sctp_auth_calculate_hmac(),
as the incorrect offset of the auth chunk in skb->data.
This fix is to requeue it by using packet->auth.
Fixes: f1533cce60 ("sctp: fix panic when sending auth chunks")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1f ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the error handling case of nla_nest_start() failed read_unlock_bh()
is called to unlock a lock that had not been taken yet. sparse warns
about the context imbalance as the following:
net/tipc/monitor.c:799:23: warning:
context imbalance in '__tipc_nl_add_monitor' - different lock contexts for basic block
Fixes: cf6f7e1d51 ('tipc: dump monitor attributes')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
