In order to better fit DT parsing in of regulator definitions re-arrange
the platform data struct slightly which requires the definitions of
the regulator IDs earlier in the include file.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the platform data and data structures for children that shall be
added by a future set of commits.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
There are charger and battery measurement feature for 88pm860x PMIC.
For charger, it can support pre-charge with small current when battery is
nearly exausted and then changed into fast-charge with CC&CV mode.
For battery monitor, it can support battery measurement such as
vbat,vsys,vchg and ibat etc,it can aslo accumulating the Coulomb value
charged or discharged from battery based on Conlomb Counter, we use it
to estimate battery capacity.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
We continue to allow the AB8500 CODEC to be registered via the AB8500
Multi Functional Device API, only this time we extract its configuration
from the Device Tree binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move probe() and other functions from 88pm860x-i2c.c to 88pm860x-core.c.
Since it could benefit to handle DT information.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add needed platform data structure and code to be able to load
the GPO child of twl6040.
Update the devicetree binding documentation at the same time.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "maxim,system-power-controller" to indicate whether the
PMIC is in charge of controlling the system power. If this is set, the
driver will provide the pm_power_off() function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for Device Tree enablement all IRQ controllers
should control their own IRQ domain. This patch provides just
that.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
From Tony Lindgren:
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
* tag 'omap-cleanup-sparseirq-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: Move SoC specific headers from plat to mach for omap1
ARM: OMAP2+ Move SoC specific headers to be local to mach-omap2
ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+
ARM: OMAP: Remove unused old gpio-switch.h
ARM: OMAP1: Move plat/irqs.h to mach/irqs.h
ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ
ARM: OMAP2+: Prepare for irqs.h removal
W1: OMAP HDQ1W: Remove dependencies to mach/hardware.h
Input: omap-keypad: Remove dependencies to mach includes
ARM: OMAP: Move gpio.h to include/linux/platform_data
ARM: OMAP2+: Remove hardcoded twl4030 gpio_base, irq_base and irq_end
ARM: OMAP2+: Remove unused nand_irq for GPMC
ARM: OMAP2+: Make INTCPS_NR_IRQS local for mach-omap2/irq.c
ARM: OMAP1: Define OMAP1_INT_I2C locally
ARM: OMAP1: Move define of OMAP_LCD_DMA to dma.h
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MFD core now takes care of HWIRQ <-> VIRQ mapping, so the helper
ab8500_irq_get_virq() is no longer used by ab8500 subordinate devices
to obtain a Linux wide Virtual IRQ. The AB8500 IRQ controller still
uses it internally though, so we'll just hide it from the rest of the
world by making it static instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ICH chips have their GPIO pins organized in 2 or 3 independent
groups of 32 GPIO pins. It can happen that the ACPI BIOS wants to make
use of pins in one group, preventing the OS to access these. This does
not prevent the OS from accessing the other group(s).
This is the case for example on my Asus Z8NA-D6 board. The ACPI BIOS
wants to control GPIO 18 (group 1), while I (the OS) need to control
GPIO 52 and 53 (group 2) for SMBus multiplexing.
So instead of checking for ACPI resource conflict on the whole I/O
range, check on a per-group basis, and consider it a success if at
least one of the groups is available for the OS to use.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since IORESOURCE_IO is changed to IORESOURCE_REG in 88pm860x driver,
update self-defined IORESOURCE_IO resource to register offset that
is IORESOURCE_REG in regulator driver. And split regulator platform
data array into scattered platform data.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the resources of 88pm860x leds are changed from IORESOURCE_IO
to IORESOURCE_REG that is register offset, change the original
self-defined IORESOURCE_IO to register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now resource of 88pm860x backlight is changed from IORESOURCE_IO
to IORESOURCE_REG. In original driver, the resource is using
self-defined IORESOURCE_IO. So change the resource to register
offset to match the definition of IORESOURCE_REG.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.
[swarren: Instantiate the sys regulator from board-harmony-power.c to
avoid regression.]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
The irq_to_gpio function was removed from the pxa platform
in linux-3.2, and this driver has been broken since.
There is actually no in-tree user of this driver that adds
this platform device, but the driver can and does get enabled
on some platforms.
Without this patch, building ezx_defconfig results in:
drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work':
drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac96: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
The delta between twl6040 and twl6041 is small, the main difference is in
the number of GPOs (3 on twl6040, 1 on twl6041).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6040 ES1.1 and ES1.2 have the same revid (0x01).
ES1.3 of twl6040 REVID is 0x02.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull sound update from Takashi Iwai:
"This is a fairly quiet release in all sound area. Only a little bit
of changes in the core side while most of changes are seen in the
drivers.
HD-audio:
- A few new codec additions for Nvidia, Realtek and VIA
- Intel Haswell audio support
- Support for "phantom" jacks for consistent jack reporting
- Major clean-ups in HDMI/DP driver codes
- A workaround for inverted digital-mic pins with Realtek codecs
- Removal of beep_mode=2 option
ASoC:
- Added the ability to add and remove DAPM paths dynamically, mostly
for reparenting on clock changes
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500,
TI Isabelle and Wolfson Microelectronics WM5102 and WM5110
- DAPM fixes for the recent locking changes
- Fix for _PRE and _POST widgets (which have been broken for a few
releases now)
- A couple of minor driver updates
Misc
- Conversion to new dev_pm_ops in platform and PCI drivers
- LTC support and some fixes in PCXHR driver
- A few fixes and PM support for ISA OPti9xx and WSS cards
- Some TLV code cleanup
- Move driver-specific headers from include/sound to local dirs"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (212 commits)
ASoC: dapm: Fix _PRE and _POST events for DAPM performance improvements
ALSA: hda - add dock support for Thinkpad X230 Tablet
ALSA: hda - Turn on PIN_OUT from hdmi playback prepare.
ASoC imx-audmux: add MX31_AUDMUX_PORT7_SSI_PINS_7 define
ASoC: littlemill: Add userspace control of the WM1250 I/O
ASoC: wm8994: Update micdet for irqdomain conversion
ALSA: hda - make sure alc268 does not OOPS on codec parse
ALSA: hda - Add support for Realtek ALC282
ALSA: hda - Fix index number conflicts of phantom jacks
ALSA: opti9xx: Fix section mismatch by PM support
ALSA: snd-opti9xx: Implement suspend/resume
ALSA: hda - Add new GPU codec ID to snd-hda
ALSA: hda - Fix driver type of Haswell controller to AZX_DRIVER_SCH
ALSA: hda - add Haswell HDMI codec id
ALSA: hda - Add DeviceID for Haswell HDA
ALSA: wss_lib: Fix resume on Yamaha OPL3-SAx
ALSA: wss_lib: fix suspend/resume
ALSA: es1938: replace TLV_DB_RANGE_HEAD with DECLARE_TLV_DB_RANGE
ALSA: tlv: add DECLARE_TLV_DB_RANGE()
ALSA: tlv: add DECLARE_TLV_CONTAINER()
...
Pull MMC updates from Chris Ball:
"MMC highlights for 3.6:
Core:
- Rename cd-gpio to slot-gpio and extend it to support more slot GPIO
functions, such as write-protect.
- Add a function to get regulators (Vdd and Vccq) for a host.
Drivers:
- sdhci-pxav2, sdhci-pxav3: Add device tree support.
- sdhi: Add device tree support.
- sh_mmcif: Add support for regulators, device tree, slot-gpio.
- tmio: Add regulator support, use slot-gpio."
* tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits)
mmc: sdhci-dove: Prepare for common clock framework
mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT
mmc: omap_hsmmc: ensure probe returns error upon resource failure
mmc: mxs-mmc: Add wp-inverted property
mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access
mmc: core: reset signal voltage on power up
mmc: sd: Fix sd current limit setting
mmc: omap_hsmmc: add clk_prepare and clk_unprepare
mmc: sdhci: When a UHS switch fails, cycle power if regulator is used
mmc: atmel-mci: modify CLKDIV displaying in debugfs
mmc: atmel-mci: fix incorrect setting of host->data to NULL
mmc: sdhci: poll for card even when card is logically unremovable
mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
mmc: sdio: Change pr_warning to pr_warn_ratelimited
mmc: core: Simplify and fix for SD switch processing
mmc: sdhci: restore host settings when card is removed
mmc: sdhci: fix incorrect command used in tuning
mmc: sdhci-pci: CaFe has broken card detection
mmc: sdhci: Report failure reasons for all cases in sdhci_add_host()
mmc: s3cmci: Convert s3cmci driver to gpiolib API
...
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set the supply_name in the regulator descriptor unconditionally
and make this parameter as required parameter in the device
node for successfully registration of the regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code has been converted to use regmap APIs, the io_mutex is not needed.
Thus remove the io_mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes below section mismatch warning:
LD drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function pm800_probe() to the function .devexit.text:pm80x_deinit()
The function __devinit pm800_probe() references
a function __devexit pm80x_deinit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
pm80x_deinit() so it may be used outside an exit section.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM5110 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices. It combines an advanced DSP
feature set with a flexible, high-performance audio hub CODEC.
The support is based on the Arizona core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
