The ADC clock divider needs to be restored on resume as the register content
is lost when the ADC is powered down
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for the STw481x PMICs found in the Nomadik
family of platforms. This one uses pure device tree probing.
Print some of the OTP registers on boot and register a regulator
MFD child.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We had specified the mask twice for FLL2_SYNC_BW change the first mask
definition in a bit definition to match the other fields.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In some platforms, specially Thinkpad series, rts5249 won't be
initialized properly. So we need adjust some phy parameters to
improve the compatibility issue.
It is a little different between simulation and real chip. We have
no idea about which configuration is better before tape-out. We set
default settings according to simulation, but need to tune these
parameters after getting the real chip.
I can't explain every change in detail here. The below information is
just a rough description:
PHY_REG_REV: Disable internal clkreq_tx, enable rx_pwst
PHY_BPCR: No change, just turn the magic number to macro definitions
PHY_PCR: Change OOBS sensitivity, from 60mV to 90mV
PHY_RCR2: Control charge-pump current automatically
PHY_FLD4: Use TX cmu reference clock
PHY_RDR: Change RXDSEL from 30nF to 1.9nF
PHY_RCR1: Change the duration between adp_st and asserting cp_en from
0.32 us to 0.64us
PHY_FLD3: Adjust internal timers
PHY_TUNE: Fine tune the regulator12 output voltage
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old timeout value was based on the assumption that the minimum values are
used for the open and sample delay and no averaging is done. In fact the ADC
and touchscreen driver both use an open delay of 152 cycles and averaging over
16 samples. This patch adjusts the timeout value accordingly
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the conversion to regmap-irq irq_lock has been unused.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the register I/O functions are all simple wrappers for the regmap
equivalents inline them to provide a small code size saving and an example
of good practice.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DA9053 (up to revision bc) can corrupt internal registers when multi-write
mode is enabled and power is removed or during shutdown.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Occasionally, it is useful to map supplies from a child device onto the
MFD device. A typical usecase for this would be if the MFD device is
represented as a single node in device tree. All supplies will be
defined in device tree as existing on the MFD device. When a child
depends on frameworks which might have no knowledge of MFD to lookup
supplies on its behalf the supply will not be found.
This patch adds a list of supplies that should be looked up on the
parent rather than the child as part of the mfd_cell structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add imx6sl iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
add fec related macro define.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are required to request DBx500 PRCMU clocks from Device Tree. The
numbers used are taken directly from the Hardware Specification document.
We're moving them from the DBx500 PRCMU include file into the DT include
directory and referencing them from the former via a #include.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the workaround for double sending AUDIO_CODEC and AUDIO_DAC writes
into the SPI core, aiding refactoring to eliminate the ASoC custom I/O
functions and avoiding the extra writes for I2C.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jonathan writes:
First round of new drivers, functionality and cleanups for IIO in the 3.13 cycle
A number of new drivers and some new functionality + a lot of cleanups
all over IIO.
New Core Elements
1) New INT_TIME info_mask element for integration time, which may have
different effects on measurement noise and similar, than an amplifier
and hence is different from existing SCALE. Already existed in some
drivers as a custom attribute.
2) Introduce a iio_push_buffers_with_timestamp helper to cover the common
case of filling the last 64 bits of data to be passed to the buffer with
a timestamp. Applied to lots of drivers. Cuts down on repeated code and
moves a slightly fiddly bit of logic into a single location.
3) Introduce info_mask_[shared_by_dir/shared_by_all] elements to allow support
of elements such as sampling_frequency which is typically shared by all
input channels on a device. This reduces code and makes these controls
available from in kernel consumers of IIO devices.
New drivers
1) MCP3422/3/4 ADC
2) TSL4531 ambient light sensor
3) TCS3472/5 color light sensor
4) GP2AP020A00F ambient light / proximity sensor
5) LPS001WP support added to ST pressure sensor driver.
New driver functionality
1) ti_am335x_adc Add buffered sampling support.
This device has a hardware fifo that is fed directly into an IIO kfifo
buffer based on a watershed interrupt. Note this will act as an example
of how to handle this increasingly common type of device.
The only previous example - sca3000 - take a less than optimal approach
which is largely why it is still in staging.
A couple of little cleanups for that new functionality followed later.
Core cleanups:
1) MAINTAINERS - Sachin actually brought my email address up to date because
I said I'd do it and never got around to it :)
2) Assign buffer list elements as single element lists to simplify the
iio_buffer_is_active logic.
3) wake_up_interruptible_poll instead of wake_up_interruptible to only wake
up threads waiting for poll notifications.
4) Add O_CLOEXEC flag to anon_inode_get_fd call for IIO event interface.
5) Change iio_push_to_buffers to take a void * pointer so as to avoid some
annoying and unnecessary type casts.
6) iio_compute_scan_bytes incorrectly took a long rather than unsigned long.
7) Various minor tidy ups.
Driver cleanups (in no particular order)
1) Another set of devm_ allocations patches from Sachin Kamat.
2) tsl2x7x - 0 to NULL cleanup.
3) hmc5843 - fix missing > in MODULE_AUTHOR
4) Set of strict_strto* to kstrto* conversions.
5) mxs-lradc - fix ordering of resource removal to match creation
6) mxs-lradc - add MODULE_ALIAS
7) adc7606 - drop a work pending test duplicated in core functions.
8) hmc5843 - devm_ allocation patch
9) Series of redundant breaks removed.
10) ad2s1200 - pr_err -> dev_err
11) adjd_s311 - use INT_TIME
12) ST sensors - large set of cleanups from Lee Jones and removed restriction
to using only triggers provided by the st_sensors themselves from
Dennis Ciocca.
13) dummy and tmp006 provide sampling_frequency via info_mask_shared_by_all.
14) tcs3472 - fix incorrect buffer size and wrong device pointer used in
suspend / resume functions.
15) max1363 - use defaults for buffer setup ops as provided by the triggered
buffer helpers as they are the same as were specified in max1363 driver.
16) Trivial tidy ups in a number of other drivers.
Previously the driver had only one-shot reading functionality.
This patch adds continuous sampling support to the driver.
Continuous sampling starts when buffer is enabled.
HW IRQ wakes worker thread that pushes samples to userspace.
Sampling stops when buffer is disabled by userspace.
Patil Rachna (TI) laid the ground work for ADC HW register access.
Russ Dill (TI) fixed bugs in the driver relevant to FIFOs and IRQs.
I fixed channel scanning so multiple ADC channels can be read
simultaneously and pushed to userspace.
Restructured the driver to fit IIO ABI.
And added INDIO_BUFFER_HARDWARE mode.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
Pull pin control changes from Linus Walleij:
"Here is the bulk of pin control changes for the v3.12 series. Most of
the relevant information is in the tag.
I merged in v3.11-rc7 last week to get rid of a largeish conflict
within the sunxi (AllWinner) driver in linux-next and fix up the
non-trivial merge the right way. That driver had a rather large fix
adding locking late in the release cycle.
Overall the bulk changes this time is cleanups and refactorings and
not much new features, which is nice.
- Refactorings for generic pin config handling in the core.
- Factor out a set of device tree utilities for use in all drivers,
to parse and allocate maps from the device tree.
- Some fixes to the core such as more nitpicky locking.
- Pushed down config array iteration into the drivers.
This patch is necessary for drivers that want to iterate over
configs and pile up a stack of alterations to the same register(s),
or if the driver wants to take a local spinlock when committing the
configuration.
- A new driver for the Texas Instruments Palmas PMIC by Laxman
Dewangan. This is used on the Tegra systems.
- A major cleanup and modernization of the PFC (Super Hitachi and ARM
SHmobile) pin controller and subdrivers.
- Support for the A20 and A31 sunxi (AllWinner) SoCs.
- A huge pile of fixes and cleanups: Axel Lin, Jingoo Han Dan
Carpenter, Julia Lawall and Sachin Kamat did an excellent job here"
* tag 'pinctrl-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (124 commits)
pinctrl: sunxi: Fix off-by-one for valid offset range checking
pinctrl: sunxi: drop lock on error path
pinctrl: pinconf-generic: Remove ti prefix in dev_err messages
pinctrl: rockchip: Implement .request() and .free() callbacks
pinctrl: at91: fix get_pullup/down function return
pinctrl: sh-pfc: remove unnecessary platform_set_drvdata()
pinctrl: Add s5pv210 support to pinctrl-exynos
pinctrl: utils: include export.h to avoid warnings
pinctrl: s3c24xx: off by one in s3c24xx_eint_init()
pinctrl: mvebu: testing the wrong variable
pinctrl: abx500: fix bitwise AND test
pinctrl: mvebu: Convert to use devm_ioremap_resource
pinctrl: Pass all configs to driver on pin_config_set()
pinctrl: tz1090-pdc: Convert to devm_ioremap_resource
pinctrl: tz1090: Convert to devm_ioremap_resource
pinctrl: tegra: Convert to devm_ioremap_resource
pinctrl: rockchip: Simplify pin_to_bank equation
pinctrl: spear: Convert to devm_ioremap_resource
pinctrl: rockchip: Remove of_match_ptr macro for DT only driver
pinctrl: palmas: PINCTRL_PALMAS needs to select PINMUX
...
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
Rather then open coding a cache of the vibra control registers use the
regmap cache code. Also cache the interrupt mask register, providing
a small performance improvement for the interrupt code.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This will be used to support refactoring of the ASoC CODEC driver to use
a regmap.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clear hw_pfm_en to disable hardware PFM mode, to fix a bug that in some
situation registers in 0xFDxx domain can't be accessed.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some of Palmas resources like clock, SMPSs, LDOs etc can be controlled
by external pins ENABLE1, ENABLE2 or NSLEEP.
Add support to configure these resources to externally controlled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a regmap irqchip for DA9063 IRQs. It depends on
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git tags/regmap-irq-ack-mask
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is MFD module providing access to registers and interrupts of DA906x
series PMIC. It is used by other functional modules, registered as MFD cells.
Driver uses regmap with paging to access extended register list. Register map
is divided into two pages, where the second page is used during initialisation.
This module provides support to following functional cells:
- Regulators
- RTC
- HWMON
- OnKey (power key misc input device)
- Vibration (force-feedback input device)
- Watchdog
- LEDs
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds register definitions for the DA9063 PMIC. They will be used
by the following DA9063 mfd core driver and functional module drivers.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.
Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hook up "pm_power_off" to palmas power off routine if there is DT
property "ti,system-power-controller" defined, so platform which is
powered by this regulator can be powered off properly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SMPS10 has two outputs OUT1 and OUT2 and have one input IN1.
SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either
in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures
it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be
used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using
regulator_enable().
[ axel.lin@ingics.com : Simplify regulator_desc setting for SMPS10_[OUT1|OUT2]
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Jonathan writes:
Second round of IIO fixes for the 3.11 cycle.
1) Fix a long term race in the IIO trigger handling.
This only effects cases where a single trigger is in use
by multiple devices.
2) ti_am335x fix an issue with incorrect data due to reading before
the sequencer is finished.
