This patch adds gating clock for SSS(Security SubSystem)
module on Exynos5250/5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[t.figa: Fixed sort order and group name.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Add macros which are used as Clock IDs in DT and clock file.
It also adds the documentation for the exynos5260 clocks.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
R-Car M2 has two MSTP bits for SYS-DMAC, not one.
Also bring the naming in sync with the documentation.
This issue was introduced in v3.14, in commit
4d8864c9e9 ("ARM: shmobile: r8a7791: Add
clock index macros for DT sources").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This driver can handle the clock controllers of the socs mentioned above,
as they share a common clock tree with only small differences.
The clock structure is built according to the manuals of the included
SoCs and might include changes in comparison to the previous clock
structure.
As pll-rate-tables only the 12mhz variants are currently included.
The original code was wrongly checking for 169mhz xti values [a 0 to much
at the end], so the original 16mhz pll table would have never been
included and its values are so obscure that I have no possibility to
at least check their sane-ness. When using the formula from the manual
the resulting frequency is near the table value but still slightly off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee1786 (pinctrl: single: Add support for wake-up interrupts)
that recently got merged. In addition to that we also needed commit
79d9701559 (of/irq: create interrupts-extended property) and
9ec36cafe4 (of/irq: do irq resolution in platform_get_irq) that
are now also merged.
So let's fix the wake-up events for some selected omaps so devices
booted in device tree mode won't just hang if deeper power states
are enabled, and so systems can wake up from suspend to the serial
port event.
Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments, added board LDP]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the necessary #reset-cells property to the rst-mgr node and
provide a header-file with all possible resets specified.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Define the set of CCUs and provided clocks sufficient to satisfy the
needs of all the existing clock references for BCM21664. Replace
the "fake" fixed-rate clocks used previously with "real" ones.
Note that only the minimal set of these clocks and CCUs is defined
here. More clock definitions will need to be added as required by
the addition of additional drivers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Broadcom 281xx clock code uses a #define for the compatible
string for it's clock control units (CCUs). Rather than defining
those in the C source file, define them in the header file that's
shared by both the code and the device tree source file (along with
all the clock ids).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
3.15 fixes for AT91
- one little DT fix
- the use of proper directory for clock in include/dt-bindings
it allows to remove the now empty include/dt-bindings/clk
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dt-bindings: clock: Move at91.h to dt-bindigs/clock
ARM: at91: fix spi cs on sama5d3 Xplained board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Tegra124 clock DT binding currently provides 3 clocks that don't
actually exist; 2 for NAND and one for UART5/UARTE. Delete these. While
this is technically an incompatible DT ABI change, nothing could have
used these clock IDs for anything practical, since the HW doesn't exist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This driver can handle the clock controller in the s3c2412 soc.
The clock structure is built according to the manuals of the included
SoCs and might include changes in comparison to the previous clock
structure.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The three SoCs share a common clock tree which only differs in the
existence of some special clocks.
As with all parts common to these three SoCs the driver is named
after the s3c2443, as it was the first SoC introducing this structure
and there exists no other label to describe this s3c24xx epoch.
The clock structure is built according to the manuals of the included
SoCs and might include changes in comparison to the previous clock
structure. As an example the sclk_uart gate was never handled previously
and the div_uart was made to be the clock used by the serial driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The r8a7791 has three VSP1 instances, one of them being named VSPS (which
stands for "VSP Standard"). The clock section in the SoC datasheet
misunderstood the abbreviation as meaning VSP System, and named the
corresponding clock VSP1(SY). This mistake has been carried over to the
kernel code.
Fix this by renaming the VSP1_SY clock to VSP1_S.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7790 has four VSP1 instances, two of them being named VSPS (which
stands for "VSP Standard") and VSPR (which stands for "VSP for
Resizing"). The clock section in the SoC datasheet misunderstood the
abbreviations as meaning VSP System and VSP Realtime, and named the
corresponding clocks VSP1(SY) and VSP1(RT). This mistake has been
carried over to the kernel code.
Fix this by renaming the VSP1_SY and VSP1_RT clocks to VSP1_S and VSP1_R.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge "STi DT changes part 1 v2" from Srinivas Kandagatla:
Patches : 01-02 are DT patches, adding interrupt support to pin
controller driver, Driver changes are already going via Linus W's
pinctrl tree.
Patches: 03 - 06 are DT patches for reset/softreset controller. Reset
controller driver is Acked by Philipp Zabel.
Patches: 07, 08 are DT patches, adding Ethernet controller support
patches, actual driver changes are already in v3.14-rc4 via Dave Millers
net tree.
Patches: 09, 10 are DT patches for IR driver support, actual IR driver
is already available since v3.12. Reason for the delay is due to
dependency on reset controller driver/headers.
* tag 'DT-for-v3.15-part-1-v2' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: STIH416: Add IR support.
ARM: STi: STIH415: Add IR support.
ARM: STi: STiH416: Add ethernet support.
ARM: STi: STiH415: Add ethernet support.
ARM: STi: STiH416: Add soft reset controller support.
ARM: STi: STiH416: Add reset controller support.
ARM: STi: STiH415: Add soft reset controller support.
ARM: STi: STiH415: Add reset controller support.
ARM: STi: STiH415: Add interrupt support for pin controller
ARM: STi: STiH416: Add interrupt support for pin controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit adds a bare bones driver support for TLV320AIC31XX family
audio codecs. The driver adds basic stereo playback trough headphone
and speaker outputs and mono capture trough microphone inputs.
The driver is currently missing support at least for mini DSP features
and jack detection. I have tested the driver only on TLV320AIC3111,
but based on the data sheets TLV320AIC3100, TLV320AIC3110, and
TLV320AIC3120 should work Ok too.
The base for the implementation was taken from:
git@gitorious.org:ti-codecs/ti-codecs.git ajitk/topics/k3.10.1-aic31xx
-branch at commit 77504eba0294764e9e63b4a0c696b44db187cd13.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds soft reset controller support for STiH415 and adds new
softreset lines required for other device tree nodes in the header file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds soft reset controller support for STiH415 and adds new
softreset lines required for other device tree nodes in the header file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
AM43xx devices have an extra MUX_MODE for certain pins.
Updating dt include to have MUX_MODE8 which maps to 0x8.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Suggest by Arnd: abstract mmc tuning as clock behavior,
also because different soc have different tuning method and registers.
hi3620_mmc_clks is added to handle mmc clock specifically on hi3620.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add code for device tree support of clocks in the BCM281xx family of
SoCs. Machines in this family use peripheral clocks implemented by
"Kona" clock control units (CCUs). (Other Broadcom SoC families use
Kona style CCUs as well, but support for them is not yet upstream.)
A BCM281xx SoC has multiple CCUs, each of which manages a set of
clocks on the SoC. A Kona peripheral clock is composite clock that
may include a gate, a parent clock multiplexor, and zero, one
or two dividers. There is a variety of gate types, and many gates
implement hardware-managed gating (often called "auto-gating").
Most dividers divide their input clock signal by an integer value
(one or more). There are also "fractional" dividers which allow
division by non-integer values. To accomodate such dividers,
clock rates and dividers are generally maintained by the code in
"scaled" form, which allows integer and fractional dividers to
be handled in a uniform way.
If present, the gate for a Kona peripheral clock must be enabled
when a change is made to its multiplexor or one of its dividers.
Additionally, dividers and multiplexors have trigger registers which
must be used whenever the divider value or selected parent clock is
changed. The same trigger is often used for a divider and
multiplexor, and a BCM281xx peripheral clock occasionally has two
triggers.
The gate, dividers, and parent clock selector are treated in this
code as "components" of a peripheral clock. Their functionality is
implemented directly--e.g. the common clock framework gate
implementation is not used for a Kona peripheral clock gate. (This
has being considered though, and the intention is to evolve this
code to leverage common code as much as possible.)
The source code is divided into three general portions:
drivers/clk/bcm/clk-kona.h
drivers/clk/bcm/clk-kona.c
These implement the basic Kona clock functionality,
including the clk_ops methods and various routines to
manipulate registers and interpret their values. This
includes some functions used to set clocks to a desired
initial state (though this feature is only partially
implemented here).
drivers/clk/bcm/clk-kona-setup.c
This contains generic run-time initialization code for
data structures representing Kona CCUs and clocks. This
encapsulates the clock structure initialization that can't
be done statically. Note that there is a great deal of
validity-checking code here, making explicit certain
assumptions in the code. This is mostly useful for adding
new clock definitions and could possibly be disabled for
production use.
drivers/clk/bcm/clk-bcm281xx.c
This file defines the specific CCUs used by BCM281XX family
SoCs, as well as the specific clocks implemented by each.
It declares a device tree clock match entry for each CCU
defined.
include/dt-bindings/clock/bcm281xx.h
This file defines the selector (index) values used to
identify a particular clock provided by a CCU. It consists
entirely of C preprocessor constants, to be used by both the
C source and device tree source files.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
This brings the implementation into line with the documentation.
This problem was introduced when SYS DMAC clock defines were added by
ac991dce64 ("ARM: shmobile: r8a7790: Add clock index macros for DT
sources") in v3.13-rc2. I do not believe this results in any problems as
these defines do not appear to be used anywhere yet.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tegra124 does not have gr2d and gr3d clocks. They have been replaced by the
vic03 and gpu clocks respectively.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
System Power Management Interface (SPMI) is a specification
developed by the MIPI (Mobile Industry Process Interface) Alliance
optimized for the real time control of Power Management ICs (PMIC).
SPMI is a two-wire serial interface that supports up to 4 master
devices and up to 16 logical slaves.
The framework supports message APIs, multiple busses (1 controller
per bus) and multiple clients/slave devices per controller.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Michael Bohan <mbohan@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
