PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.
So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:
ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)
Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds the divider clock id for Exynos4 memory bus frequency.
The clock id is used for DVFS (Dynamic Voltage/Frequency Scaling)
feature of the exynos memory bus.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The two big changes are the additional of the watchdog clock, which
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
Add defines to make more human readable numbers for the lpass
clock controller found on IPQ806x SoCs. Also remove the PLL4
define in gcc to avoid #define conflicts because that clock
doesn't exist in gcc, instead it lives in lcc.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Split off into separate patch]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds a new id for the pclk supplying the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
The STiH418 is advanced UHD 60fps AVC processor with 3D graphic acceleration and
quad-core ARM Cortex A9 CPU.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Process-Voltage-Temperature Monitor has two clocks, PVTM_CORE and
PVTM_GPU.
Signed-off-by: Huang Lin <hl@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are 3 different parent clock from different usbphy,
all of them are fixed 480MHz, it is not able to auto select
by clock core to the 2nd and the 3rd parent.
For different use case for different board, we may need to
select different usbphy clock out as parent manually.
Add the clock ID for it so that we can use in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
- clock phase setting capability for the rk3288 mmc clocks
- pll init to allow syncing to actual rate table values
- some more exported clocks
- fixes for some clocks (typos etc) all of them not yet used
in actual drivers
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
These clocks represent the physical clocks (including phases) and they will
later be used for clock phase tuning.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This exposes the clock that comes out of the i2s block which generally
goes to the audio codec.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
[removed CLK_SET_RATE_PARENT from original patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The DMC clocks need to be turned off at runtime, so we should have IDs
so we can export them.
Signed-off-by: Jeff Chen <cym@rock-chips.com>
[dianders: split into two patches; adjusted commit msg]
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull "Second Round of Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman:
* Add labels for LEDs on kzm9g-reference and koelsch
* Add Sound support to r8a7790/lager and r8a7791/koelsch
* Add IIC DMA nodes to r8a7790 and r8a7791
* Use SoC-specific IIC compatible properties on sh73a0 and r8a73a4
* Add SGX, MMP and VSP1 clocks to r8a7794
* Add USBDMAC{0,1} clocks to r8a7790 and r8a7791
* tag 'renesas-dt2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: shmobile: r8a7791: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7790: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7794: Add MMP and VSP1 clocks to device tree
ARM: shmobile: r8a7794: Add SGX clock to device tree
ARM: shmobile: koelsch: add Volume Ramp usage on comment
ARM: shmobile: lager: add Volume Ramp usage on comment
ARM: shmobile: r8a7791: add DMA nodes for IIC
ARM: shmobile: r8a7790: add DMA nodes for IIC
ARM: shmobile: kzm9g-reference dts: Add labels for the LEDs
ARM: shmobile: koelsch dts: Add labels for the LEDs
ARM: shmobile: sh73a0 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: r8a73a4 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: koelsch: Sound DMA support via DVC on DTS
ARM: shmobile: koelsch: Sound DMA support via SRC on DTS
ARM: shmobile: koelsch: Sound DMA support via BUSIF on DTS
ARM: shmobile: koelsch: Sound DMA support on DTS
ARM: shmobile: koelsch: Sound PIO support on DTS
ARM: shmobile: koelsch: fixup I2C2 clock frequency
ARM: shmobile: lager: Sound DMA support via DVC on DTS
ARM: shmobile: lager: Sound DMA support via SRC on DTS
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "STi DT updates for v3.19, round 2" from Maxime Coquelin:
Highlights:
-----------
- Refactor STiH407 SoC and board to add STiH410 SoC support
- Add USB support to STiH416 SoC
* tag 'sti-dt-for-v3.19-2' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: DT: STiH416: Change miphy356 node name to phy@fe382000
ARM: STi: DT: STih407: STih410: Add clk_ignore_unused to kernel bootargs
ARM: STi: DT: STiH410: Add STiH410 SoC and b2120 board support.
ARM: STi: DT: STih407: Abstract common dt nodes into shared files.
ARM: STi: DT: STiH410: Add pinctl config for usb controllers.
ARM: STi: DT: STiH410: Add defines for STiH410 DT clocks
ARM: STi: DT: STiH416: Add DT nodes for the ehci and ohci usb controllers.
ARM: STi: DT: STiH416: Add DT node for the stih415/6 usb2 phy
ARM: STi: DT: STiH416: Add pinctl setup for usb controllers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
