Some mass storage devices return a bogus value in response to a Get Max LUN
request. The Iomega Jaz USB Adapter responds with 0x10, hence my recent
patch to use the US_FL_SINGLE_LUN quirk for it.
The USB MSC Bulk Only Transport document says "The device shall return one
byte of data that contains the maximum LUN supported by the device."
Since the LUN field in the command block wrapper is only 4 bits wide, it
might be helpful to report too-large LUN values in the kernel log, and
assume max LUN is actually 0. That could get some devices which currently
need the US_FL_SINGLE_LUN quirk to work.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the hid function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before configfs is integrated the usb_gstrings_attach() interface
must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old function interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_hid interface in order for the old to be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting hid to the new function interface requires converting
the USB hid's function code and its users.
This patch converts the f_hid.c to the new function interface.
The file can now be compiled into a separate usb_f_hid.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far platform driver has been unregistered first,
so just after that the usb composite is still available,
but there is no hid data any more.
Reverse the order so that first the usb composite becomes
unavailable and second the hid data goes away.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
device_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
class_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit 0943d8ead3 ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable <stable@vger.kernel.org> # v3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
File names in the heading comments fell out of favor long ago, and these weren't
even changed when the drivers were moved from drivers/usb/otg/, so remove them
at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the midi function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support the usb_gstrings_attach must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old f_midi interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_midi interface so that the old can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting midi to the new function interface requires converting
the USB midi's function code and its users.
This patch converts the f_midi.c to the new function interface.
The file can now be compiled into a separate usb_f_midi.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kstrdup() might fail, so check its return value and react appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The soundcard index to use for the ALSA device creation is passed as a
parameter to f_midi_bind_config(), but is assigned to midi->index only
after the call to f_midi_register_card(midi). So no matter what is passed
to f_midi_bind_config(), the actual index for snd_card_new() is always 0.
This probably works ok if at the moment of f_midi's bind there are no
other snd_cards, but if there are, it is not possible to bind f_midi.
This patch moves the assignment to a place before the call to
f_midi_register_card(midi).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uac1 and uac2 functions are available through the configfs interface
and it should be possible to build them without building their legacy
gadgets.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Attaching a keyboard, using it as a wakeup via
|for f in $(find /sys/devices/ocp.3/47400000.usb -name wakeup)
|do
| echo enabled > $f
|done
going into standby
| echo standby > /sys/power/state
and now a wake up by a pressing a key.
What happens is that the system wakes up but the USB device is dead. The
USB stack tries to send a few control URBs but nothing comes back.
Eventually it gaves up and the device remains dead:
|[ 632.559678] PM: Wakeup source USB1_PHY
|[ 632.581074] PM: noirq resume of devices complete after 21.261 msecs
|[ 632.607521] PM: early resume of devices complete after 10.360 msecs
|[ 632.616854] net eth2: initializing cpsw version 1.12 (0)
|[ 632.704126] net eth2: phy found : id is : 0x4dd074
|[ 636.704048] libphy: 4a101000.mdio:00 - Link is Up - 1000/Full
|[ 638.444620] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 653.713435] usb 1-1: device descriptor read/64, error -110
|[ 669.093435] usb 1-1: device descriptor read/64, error -110
|[ 669.473424] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 684.743436] usb 1-1: device descriptor read/64, error -110
|[ 690.065097] PM: resume of devices complete after 57450.744 msecs
|[ 690.076601] PM: Finishing wakeup.
|[ 690.076627] Restarting tasks ...
It seems that since we got woken up via MUSB_INTR_RESUME the
musb_host_finish_resume() callback is executed before the
resume-callbacks of the PHY and glue layer are invoked. If I delay it
until the glue layer resumed then I don't see this problem.
I also move musb_host_resume_root_hub() into that callback since I don't
see any reason in doing anything resume-link if there are still pieces
not restored.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure to only raise DTR on transitions from B0 in set_termios.
Also allow set_termios to be called from open with a termios_old of
NULL. Note that DTR will not be raised prematurely in this case.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The am335x-evmsk support two kinds of suspend:
- standby
the USB device remains powered while the system goes into suspend
- mem
the USB device becomes powerless while the system goes into suspend.
In the "standby" case the device resumes quickly. In the "mem" case the
system hangs for a few seconds. It seems to me that the USB-device has
no address (it was disconnected) and the USB stack thinks that it is
fully operational and GetPortStatus returns the status from before the
suspend so it is not a big help here.
This adds a check in the resume path to see if the device mode (A or B)
and the speed is the same. If the device went missing between
suspend/resume (VBUS went down) then MUSB seems to go into B mode and
HS/FS bits are cleared. In that case we clear the port1_status bits and
assume a disconnect. Once the stack learns this it does a "logical
disconnect" and removes the USB-device quickly. Should the device remain
connected during the suspend then MUSB will receives a "CONNECT" interrupt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DCPCTR doesn't have the ACLRM bit, the usbus_pipe_clear()
should not call the usbhsp_pipectrl_set() with ACLRM.
So, this patch fixes this issue to add the usbhs_fifo_clear_dcp()
in fifo.c because the controller needs the CFIFO to clear the
the DCP PIPE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, this driver should clear the INTSTS0.CTRT
bit before this controller detects the next stage transition. Otherwise,
the driver may not be able to clear the bit after the controller went to
the next stage transition. After that, the driver will not be able to
clear the INTSTS0.VALID, and a usb control transfer will not finish
finally.
If we use the testusb tool, it is easy to reproduce this issue:
# testusb -a -t 10
Since the previous code handled a data stage and a status stage in
the usbhsf_pio_try_push(), it may not clear the INTSTS0.CTRT at the
right timing.
So, this patch change the timing of usbhs_dcp_control_transfer_done()
to the usbhsg_irq_ctrl_stage().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that this driver always enable the D+ pullup
after it detected the VBUS connection even though this usb controller
can control the D+ pullup timing by software. So, this driver should
enable the D+ pullup after a gadget driver called usb_gadget_connect().
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the NULL pointer dereference happens
when we uses g_audio driver. Since the g_audio driver will call
usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(),
the uep->pipe of renesas usbhs driver will be NULL. So, this patch
adds a condition to avoid the oops.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2f98382dc (usb: renesas_usbhs: Add Renesas USBHS Gadget)
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for Google devices that export simple serial
interfaces using the vendor specific SubClass/Protocol pair
0x50/0x01.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
[johan: move id entries and update Kconfig]
Signed-off-by: Johan Hovold <johan@kernel.org>
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
