Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PLX USB2380 is a PCIe version of the NET2280 and behaves more like the
USB338x but without the USB3.0 superspeed support.
This was tested with g_ether, g_serial, g_mass_storage on a Gateworks
Ventana GW2383.
Cc: Justin DeFields <justindefields@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With a default size of 16kiB and with maximum of 32
buffers, we can transfer up to 512kiB, however Linux
can transfer up to 1MiB in a single mass storage
block transfer to USB3 storage devices.
Because of this, 1MiB block transfers end up being
slower than 512kiB block transfers. Let's increase
maximum number of storage buffers to a ridiculous
amount (256) so that anybody wanting to test maximum
achievable throughput can do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
valid range for storage buffers is encoded in
Kconfig already. Instead of checking again, let's
drop fsg_num_buffers_validate() altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's annoying to constantly see the same "Not yet implemented" message
over and over with nothing able to be done about it, so rate limit it
for now to keep user's logs "clean".
Reported-by: Lars Täuber <lars.taeuber@web.de>
Tested-by: Lars Täuber <lars.taeuber@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB LED driver exposes a undocumented sysfs interface and doesn't
use the standard kernel LED subsystem. It supports three devices:
Delcom Visual Signal Indicator
The driver supports generation 1 of the device only which was
manufactured until 2008. Remove support for this device completely.
Riso Kagaku RGB LED + Dream Cheeky Webmail Notifier
These devices are HID compliant and are supported by a new USB LED
driver under drivers/hid utilizing the kernel LED subsystem.
So let's remove the old USB LED driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for shared platform controllers by using
devm_reset_control_get_shared_by_index instead of
of_reset_control_get_by_index.
Note we use the devm function because there is no
of_reset_control_get_shared_by_index, this also leads
to a nice cleanup of the cleanup code.
This brings the ehci-platform reset handling code inline
with ohci-platform.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least the EHCI/OHCI found on the Allwinnner H3 SoC needs multiple
reset lines, the controller will not initialize while the reset for
its companion is still asserted, which means we need to de-assert
2 resets for the controller to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to the save power consumption, as a workaround, suspend
forcibly the USB PORTA/B/C via set the SUSPEND_A/B/C bits of OHCI
Interrupt Configuration Register in the SFRs while OHCI USB suspend.
This suspend operation must be done before the USB clock is disabled,
resume after the USB clock is enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver supports two paths of device instantiation: as platform and i2c
device. In the platform path it lacks of storing the driver specific
structure as drvdata.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only caller of get_gadget_descs() has already dereferenced udc
before calling this function, so udc can not be NULL at this point of
the code and hence no use of checking it.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stub_disconnect() calls stub_device_reset() during usb_unbind_device() when
usb device is locked. So usb_lock_device_for_reset() in stub_device_reset()
in that case polls for one second and returns -EBUSY anyway.
Remove useless flag USBIP_EH_RESET from SDEV_EVENT_REMOVED.
Signed-off-by: Alexander Popov <alpopov@ptsecurity.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ehci compatible controllers have more than one reset signal lines,
e.g., Synopsys DWC USB2.0 Host-AHB Controller has two resets hreset_i_n
and phy_rst_i_n. Two more resets are added in this patch in order for
this kind of controller to use this driver directly.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a suspend/resume issue where the driver is blindly
calling ehci_suspend/resume functions when the ehci hasn't been setup.
This results in a crash during suspend/resume operations.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <pramod.gurav@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 0b52297f22 ("reset: Add support for shared reset
controls") there is a reference count for reset control assertions. The
goal is to allow resets to be shared by multiple devices and an assert
will take effect only when all instances have asserted the reset.
In order to preserve backwards-compatibility, all reset controls become
exclusive by default. This is to ensure that reset_control_assert() can
immediately assert in hardware.
However, this new behaviour triggers the following warning in the EHCI
driver for Tegra:
[ 3.365019] ------------[ cut here ]------------
[ 3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c
[ 3.382151] Modules linked in:
[ 3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140
[ 3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[ 3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14)
[ 3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4)
[ 3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100)
[ 3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28)
[ 3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c)
[ 3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518)
[ 3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0)
[ 3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330)
[ 3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc)
[ 3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c)
[ 3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218)
[ 3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8)
[ 3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170)
[ 3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8)
[ 3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114)
[ 3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c)
[ 3.529361] ---[ end trace 4bda87dbe4ecef8a ]---
The reason is that Tegra SoCs have three EHCI controllers, each with a
separate reset line. However the first controller contains UTMI pads
configuration registers that are shared with its siblings and that are
reset as part of the first controller's reset. There is special code in
the driver to assert and deassert this shared reset at probe time, and
it does so irrespective of which controller is probed first to ensure
that these shared registers are reset before any of the controllers are
initialized. Unfortunately this means that if the first controller gets
probed first, it will request its own reset line and will subsequently
request the same reset line again (temporarily) to perform the reset.
This used to work fine before the above-mentioned commit, but now
triggers the new WARN.
Work around this by making sure we reuse the controller's reset if the
controller happens to be the first controller.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".
With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the Araneus Alea I USB hardware Random Number
Generator which is interfaced with in exactly the same way as the
Altus Metrum ChaosKey. We just add the appropriate device ID and
modify the config help text.
Signed-off-by: Bob Ham <bob.ham@collabora.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Cc: <stable@vger.kernel.org> # v4.2+
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the state for the PHY with delayed_work
as otherwise MUSB will get confused and idles immediately.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the pull up being handled with delayed work, we can
now finally remove pm_runtime_set_irq_safe that blocks the
MUSB glue from idling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least 2430 glue layer pulls d+ high on start up even if there are
no gadgets configured. This is bad at least for anything using a separate
battery charger chip as it can confuse the charger detection.
Let's fix the issue by removing the bogus glue layer code tinkering
with the SESSION bit. As pointed out Bin Liu <b-liu@ti.com> and
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>, the SESSION
bit just starts host mode if ID pin is grounded, and starts the
srp is ID pin is floating. So without the ID pin changing, it's
unable to force musb mode to anything. And just for starting a
host mode, things work fine without this code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.
The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This simplifies things and allows idling both MUSB and PHY
when nothing is configured. Let's just return early from PM
runtime if musb is not yet initialized.
Let's also warn if PHY is not configured.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may have drivers loaded but no configured gadgets and MUSB may be in
host mode. If gadgets are configured during host mode, PM runtime will
get confused.
Disable PM runtime from gadget state, and do it based on the cable
and last state.
Note that we may get multiple cable events, so we need to keep track
of the power state.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have MUSB setting pm_runtime_irq_safe with the following
commits:
30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
3e43a07256 ("usb: musb: core: add pm_runtime_irq_safe()")
Let's fix things to use delayed work so we can remove the
pm_runtime_irq_safe.
Note that we may want to set this up in a generic way in the
gadget framework eventually.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional use of PM runtime does not work properly
for musb gadget. On cable disconnect we may not get any
USB_EVENT_NONE leaving the PM runtime call unpaired.
Let's fix the issue by making sure the PM runtime calls are
paired within the functions. The glue layer will take care
of the rest.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's not tinker with the PM runtime of musb core from the omap2430
wrapper. This allows us to initialize PM runtime for musb core later
on instead of doing it in stages. And omap2430 wrapper has no need
to for accessing musb core at this point.
Note that this does not remove all the PM runtime calls from the
glue layer, those will get removed in a later patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's make the PM runtime use the standard autosuspend calls.
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") means we must pair use_autosuspend with
dont_use_autosuspend and then use put_sync to properly idle the
device.
Note that we'll be removing the PM runtime calls from the glue
layer to the MUSB core in the next patch. And we can also remove
the pointless FIXME comment now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have remove() already calling shutdown(), so let's drop it
and move the code to remove(). No code changes, we'll drop the
the FIXME in the following patch with more clean-up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like at least 2430 glue won't idle reliably with the 200 ms
autosuspend delay. This causes deeper idle states being blocked for
the whole SoC when disconnecting OTG A cable.
Increasing the delay to 500 ms seems to idle both MUSB and the PHY
reliably. This is probably because of time needed by the hardware
based negotiation between MUSB and the PHY.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
