Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdcea058e5 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.
The __raw_readq/__raw_writeq is introduced by commit bca2092d78 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.
So for 64BIT && !PORT_OCTEON, we better to use coincident write function.
Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are managed through clk-fractional-divider.c module, and thus CLK
framework takes care about it. Remove letfovers from this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct call to readl()/writel() is checked against iotype
and in case of UPIO_MEM32BE we use ioread32be()/iowrite32be()
instead of them.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UPIO_MEM32BE in addition to UPIO_MEM32.
For big endian we use 2 new accessors similar to little endian,
called dw8250_serial_out32be() and dw8250_serial_in32be().
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the help of Heikki we take common code that
makes sure LCR write wasn't ignored and put it in new function called
dw8250_check_lcr(). This function serves 3 serial_out routines:
dw8250_serial_out(), dw8250_serial_out32(), and dw8250_serial_outq().
This patch only brings better code reuse.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull clk updates from Stephen Boyd:
"The majority of the changes are driver updates and new device support.
The core framework is mostly unchanged this time around, with only a
couple patches to expose a clk provider API and make getting clk
parent names from DT more robust.
Driver updates:
- Support for clock controllers found on Broadcom Northstar SoCs and
bcm2835 SoC
- Support for Allwinner audio clocks
- A few cleanup patches for Tegra drivers and support for the highest
DFLL frequencies on Tegra124
- Samsung exynos7 fixes and improvements
- i.Mx SoC updates to add a few missing clocks and keep debug uart
clocks on during kernel intialization
- Some mediatek cleanups and support for more subsystem clocks
- Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
controllers
- A new driver for the Silabs si514 clock chip"
* tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (143 commits)
clk: qcom: msm8960: Fix dsi1/2 halt bits
clk: lpc18xx-cgu: fix potential system hang when disabling unused clocks
clk: lpc18xx-ccu: fix potential system hang when disabling unused clocks
clk: Add clk_hw_is_enabled() for use by clk providers
clk: Add stubs for of_clk_*() APIs when CONFIG_OF=n
clk: versatile-icst: fix memory leak
clk: Remove clk_{register,unregister}_multiplier()
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
clk: imx31: add missing of_node_put
clk: imx27: add missing of_node_put
clk: si5351: add missing of_node_put
...
Using the same style of declaring variables as used in the
other functions of the driver. Passing uart_port to the
function instead of uart_8250_port, as it is the one mostly
needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding comment where the purpose of the function is
explained.
The dma parameters are not used, so removing them, and also
moving the assignment of the function to the same place
where the other dw8250_data structures members are being set
in dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DW_apb_uart is configured with UART_16550_COMPATIBLE
configuration parameter set, then the Busy Functionality is
not available. These UARTs will never generate the Busy
detect indication interrupt, and therefore don't need
handling for it.
This creates a small optimization for the DW_apb_uarts
configured without the busy functionality, but more
importantly, it removes the small but real risk of hitting
potential issues caused by busy functionality handling when
no busy functionality exist.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merging the DT and ACPI specific probe functions into
dw8250_quirks. Those functions did not have that much code
any more and some of the quirks need to be shared. This
will also allow platforms without DT or ACPI to use the
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a flag "skip_autocfg" that the platforms that do
not have the ADDITIONAL_FEATURES implemented can use to skip
the port setup. It's then enough to call dw8250_setup_port
just from dw8250_probe based on that flag.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have couple of standard but rare used baudrates which are not supported by
1,8432MHz reference frequency. Besides that user can potentially ask for any
baudrate (via BOTHER flag) and we currently don't fully support that. Since
clk-fractional-divider is moved to use rational best approximation for
reference frequency we may amend the driver to support whatever user wants.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the serial core is informed that this device is doing
automatic flow control, it is not necessary to alter CTS and
DCTS of the MSR as the core no longer attempts stop the port
in uart_handle_cts_change().
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many new Intel SoCs the UART has an integrated DMA engine
(iDMA). In order to use it a special filter function is needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with CTS, not DSR here (we dealt with DSR a few lines
above), so set appropriate bits.
Reported-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to write console output from within the serial console driver
while the port->lock is held causes recursive deadlock:
CPU 0
spin_lock_irqsave(&port->lock)
printk()
console_unlock()
call_console_drivers()
serial8250_console_write()
spin_lock_irqsave(&port->lock)
** DEADLOCK **
The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.
Make the error message a FIXME until a general solution is devised.
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable APM X-Gene SoC serial port functionality when using ACPI table to
initialize serial port.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get index of serial line from device tree using function of_alias_get_id().
If no alias is found, the 8250 core takes care of incrementing the line number.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma pointer under struct uart_8250_port is currently left
unassigned for non-ACPI platforms. It should be pointing to the dma
member in struct dw8250_data like how it was done for ACPI, so the core
8250 code will try to request for DMA when registering the port
If DMA is not enabled in device tree, request DMA will fail and the
driver will fall back to PIO
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
That field has been deprecated in favour of getting the necessary information
from ACPI or DT.
However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
