If the user adds an obscene amount of MAC addresses, the driver will run
into the situation where it has too many address requests to fit into a
single PF message. The driver checks for this case, and calculates the
maximum number of messages that it can send. Then it completely ignores
this count and overflows the buffer.
Fix this by checking the address count and bailing out of the loop at
the appropriate time.
Change-ID: If8dcbb04602c75941dc0cd8309065e1de9ca791c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions to enable and disable default VSI on a VEB. This allows
for configuration of limited promiscuous mode specifically for bridging
purposes.
Change-ID: I0cc5bd68b31c500fdff4d47e1f15d50d2739faf4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no prevention of a concurrent call to both fixed_mdio_read()
and fixed_phy_update_state(), which can result in the state being
modified while it's being inspected. Fix this by using a seqcount
to detect modifications, and memcpy()ing the state.
We remain slightly naughty here, calling link_update() and updating
the link status within the read-side loop - which would need rework
of the design to change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate software phy registers as and when requested, rather than
duplicating the state in fixed_phy. This allows us to eliminate
the duplicate storage of of the same data, which is only different
in format.
As fixed_phy_update_regs() no longer updates register state, rename
it to fixed_phy_update().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate out the generation of MII registers from the state validation.
This allows us to simplify the error handing in fixed_phy() by allowing
earlier error detection.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the swphy register generation to tabular form which allows us
to eliminate multiple switch() statements. This results in a smaller
object code size, more efficient, and easier to add support for faster
speeds.
Before:
Idx Name Size VMA LMA File off Algn
0 .text 00000164 00000000 00000000 00000034 2**2
text data bss dec hex filename
388 0 0 388 184 swphy.o
After:
Idx Name Size VMA LMA File off Algn
0 .text 000000fc 00000000 00000000 00000034 2**2
5 .rodata 00000028 00000000 00000000 00000138 2**2
text data bss dec hex filename
324 0 0 324 144 swphy.o
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 4 patches for net-next/master.
Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2016-06-23
this is a pull request of 3 patches for the upcoming linux-4.7 release.
The first two patches are by Oliver Hartkopp fixing oopes in the generic CAN
device netlink handling. Jimmy Assarsson's patch for the kvaser_usb driver adds
support for more devices by adding their USB product ids.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fixes to spelling mistakes of the words "excessive collisions"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.
Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new get/set link ksettings and remove get/set settings legacy
callbacks.
This allows us to use bitmasks longer than 32 bit for supported and
advertised link modes and use modes that were previously not supported.
Signed-off-by: Gal Pressman <galp@mellanox.com>
CC: Ben Hutchings <bwh@kernel.org>
CC: David Decotigny <decot@googlers.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this mode the moderation timer will restart upon
new completion (CQE) generation rather than upon interrupt
generation.
The outcome is that for bursty traffic the period timer will never
expire and thus only the moderation frames counter will dictate
interrupt generation, thus the interrupt rate will be relative
to the incoming packets size.
If the burst seizes for "moderation period" time then an interrupt
will be issued immediately.
CQE based moderation is off by default and can be controlled
via ethtool set_priv_flags.
Performance tested on ConnectX4-Lx 50G.
Less packet loss in netperf UDP and TCP tests, with no bw degradation,
for both single and multi streams, with message sizes of
64, 1024, 1472 and 32768 byte.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an infrastructure for getting/setting private net device
flags.
Currently a 'nop' priv flag is added, following patches will override
the flag will actual feature specific flags.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_maxrate ndo.
Use the rate index from the hardware table to attach to channel SQ/TXQ.
In case of failure to configure new rate, the queue remains with
unlimited rate.
We save the configuration on priv structure and apply it each time
Send Queues are being reinitialized (after open/close) operations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.
The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.
The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge. BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.
This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)
Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.
Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.
Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.
In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid 88E6352 entry with 88E6XXX, maintained by
Andrew and myself.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
