In order to allow drivers to override specific dsa_switch_driver
callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids
having to expose this structure to glue drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of trapping certain packets to the CPU and then relying on it to
flood them we can instead make the device mirror them.
The following packet types are mirrored:
* DHCP: Broadcast packets that should be flooded by the device, but also
trapped in case CPU is running the DHCP server.
* IGMP query: Multicast packets that need to be forwarded to other
bridge ports, but also trapped so that receiving netdev will be marked
as a router port by the bridge driver.
* ARP request: Broadcast packets that should be forwarded to other
bridge ports, but also trapped in case requested IP is of the local
machine.
* ARP response: Unicast packets that should be forwarded by the bridge
but also trapped in case response is directed at us.
Set the trap action of such packets to mirror and mark them using
'offload_fwd_mark' to prevent the bridge driver from forwarding them
itself.
Note that OSPF packets are also marked despite their action being trap.
The reason for this is that the device traps such packets in the
pipeline after they were already flooded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only trapped packets to CPU, but we are going to allow
some packets to be mirrored (trap & forward) to CPU.
Extend the Rx listener with 'action' member.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of copying & pasting the same struct initialization for every
Rx listener, just use a macro.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When team is in bridge and LACP is utilized, LACPDU packets are pushed
to userspace using raw socket and there they are processed. However,
since 8626c56c82, LACPDU skbs are dropped by bridge rx_handler so
they never reach packet handlers in rx path. Fix this by explicity treat
LACPDUs to be pushed to exact delivery in team rx_handler.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppe_cb->ppe_common_cb is being dereferenced before a null check is
being made on it. If ppe_cb->ppe_common_cb is null then we end up
with a null pointer dereference when assigning dsaf_dev. Fix this
by moving the initialisation of dsaf_dev once we know
ppe_cb->ppe_common_cb is OK to dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b17c706987 ("loopback: sctp: add NETIF_F_SCTP_CSUM to device
features") added NETIF_F_SCTP_CRC to device features for lo device to
improve the performance of sctp over lo.
This patch is to add NETIF_F_SCTP_CRC to device features for veth to
improve the performance of sctp over veth.
Before this patch:
ip netns exec cs_client netperf -H 10.167.12.2 -t SCTP_STREAM -- -m 10K
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
212992 212992 10240 10.00 1117.16
After this patch:
ip netns exec cs_client netperf -H 10.167.12.2 -t SCTP_STREAM -- -m 10K
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
212992 212992 10240 10.20 1415.22
Tested-by: Li Shuang <tjlishuang@yeah.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cp_rx_poll does not get enough packet, it will check the rx
interrupt status again. If so, it will jumpt to rx_status_loop again.
But the goto jump resets the rx variable as zero too.
As a result, it causes one possible deadloop. Assume this case,
rx_status_loop only gets the packet count which is less than budget,
and (cpr16(IntrStatus) & cp_rx_intr_mask) condition is always true.
It causes the deadloop happens and system is blocked.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.
Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
commit 33c133cc75 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we keep shadow copies of which interrupt sources are enabled
through the intrl2_*_mask_{set,clear} macros, make sure that the
ordering in which we do these two operations: update the copy, then
unmask the register is correct.
This is not currently a problem because we actually do not use them, but
we will in a subsequent patch optimizing register accesses, so better be
safe here.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/vmxnet3/vmxnet3_drv.c:1645:1: warning:
symbol 'vmxnet3_rq_destroy_all_rxdataring' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the dma_map_single error
handling case instead of 0, as done elsewhere in this function.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Hip06 SoC, the RoCE Engine is part of the Hisilicon Network
Subsystem and is dependent upon DSAF module. Therefore, certain
functions like RESET are exposed through the common registers of
HNS DSAF module which are memory-mapped by the HNS driver and
currently can only be accessed through DT/syscon interface.
This patch adds the support of ACPI to the existing RoCE reset
function in the HNS driver(please refer NOTE 2). Hisilicon RoCE
driver (please refer NOTE 1) shall call this reset function during
probe time to reset the RoCE Engine.
The HNS Reset function indirectly ends up in calling the _DSM()
function part of the DSDT ACPI Table. Actual reset functionality
for ACPI is implemented within the ACPI DSDT Table which also has
been enhanced to support this change.
Support of ACPI in the HNS RoCE driver shall be pushed through a
different accompanying below patch:
"IB/hns: Add support of ACPI to the Hisilicon RoCE Driver"
NOTE 1: HNS RoCE driver has already been accepted by its maintainer
Doug Ledford<dledford@redhat.com>. Please refer below link:
https://www.spinics.net/lists/linux-rdma/msg38850.html
NOTE 2: RoCE reset function patch has been accepted and now is
part of the net-next:
https://www.mail-archive.com/netdev@vger.kernel.org/msg123867.html
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Mellanox ConnectX-4/Connect-IB shared code (SW part)
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_set_rx_mode() is called for bnx2x, as part of process of
configuring the new MAC address filters [both unicast & multicast]
driver begins by flushing the existing configuration and then iterating
over the network device's list of addresses and configures those instead.
This has the side-effect of creating a short gap where traffic wouldn't
be properly classified, as no filters are configured in HW.
While for unicasts this is rather insignificant [as unicast MACs don't
frequently change while interface is actually running],
for multicast traffic it does pose an issue as there are multicast-based
networks where new multicast groups would constantly be removed and
added.
This patch tries to remedy this [at least for the newer adapters] -
Instead of flushing & reconfiguring all existing multicast filters,
the driver would instead create the approximate hash match that would
result from the required filters. It would then compare it against the
currently configured approximate hash match, and only add and remove the
delta between those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we used to assign vFIDs to the created vPorts. Since
these vPorts were used for slow path traffic we had to disable learning
for them, as it doesn't make sense to have it enabled.
This is no longer the case and now vPorts are either used for router
interfaces (for which learning is disabled by the firmware) or bridge
ports (for which learning is explicitly enabled by the driver).
Therefore, we can remove the learning configuration upon vPort creation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now offload the learning configuration to the device and don't rely
on the driver to decide whether to learn the FDB record, so remove the
check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we simply stored the learning configuration of a bridge
port in the driver and decided whether to learn a new FDB record based
on this value.
However, this is sub-optimal in cases where learning is disabled on the
bridge port, as the device repeatedly generates learning notifications
for the same record.
Instead, offload the learning configuration to the device, thereby
preventing it from generating notifications when learning is disabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing VLANs from the VLAN-aware bridge we shouldn't abort on the
first error, as we'll otherwise have resources that will never be freed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05978481e7 ("mlxsw: spectrum: Create PVID vPort before
registering netdevice") removed __mlxsw_sp_port_vlans_del() from the
init sequence of the driver, which forced it to be non-symmetric with
regards to __mlxsw_sp_port_vlans_add().
Make both functions symmetric as the constraint no longer exists.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.
Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the function mlxsw_router_neigh_construct search the rif according
to the neighbour dev other than the dev that was passed to the ndo, thus
allowing creating neigbhours upon stacked devices.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we have a layer 3 interface on top of a bridge (VLAN / FID RIF),
then we should flood the following packet types to the router:
* Broadcast: If DIP is the broadcast address of the interface, then we
need to be able to get it to CPU by trapping it following route lookup.
* Reserved IP multicast (224.0.0.X): Some control packets (e.g. OSPF)
use this range and are trapped in the router block.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-08-24
This series contains some low level and API updates for mlx5 core
driver interface and mlx5_ifc.h, plus mlx5 LAG core driver support,
to be shared as base code for net-next and rdma mlx5 4.9 submissions.
From Alex and Artemy, Update mlx5_ifc for modify RQ and XRC bits.
From Noa, Expose mlx5 link modes so they can be used in RDMA tree for rdma tools.
From Aviv, LAG support needed for RDMA.
- Add needed hardware structures, layouts and interface
- mlx5 core driver LAG implementation
- Introduce mlx5 core driver LAG API for mlx5_ib
From Maor, add two low level patches for mlx5 hardware sniffer QP
infrastructure bits and capabilities, plus added the namespace for sniffer
steering tables. Needed for RDMA subtree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda2977291 (tun: Support software transmit time stamping.)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Francis Yan <francisyyan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return type of ena_set_push_mode() to be void,
as it always returns 0.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/phy/xilinx_gmii2rgmii.c:61:5: warning:
symbol 'xgmiitorgmii_probe' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently enable interrupts before we enable NAPI. If an RX interrupt
hits before we enabled NAPI then the NAPI callback is never called and
we leave the hardware with RX interrupts disabled, which of course leads
us to never handling received packets. Fix this by moving the interrupt
enable to after we've enable NAPI and the reclaim tasklet.
Fixes: cd5e412347 ("dwc_eth_qos: do phy_start before resetting hardware")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so we should better check its return
value and propagate it in the case of failure
While at it, replace __lpc_eth_clock_enable() with a plain
clk_prepare_enable/clk_disable_unprepare() call in order to
simplify the code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.
Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.
Fixes: 7829451c69 ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
liquidio_set_rxcsum_command is a local function only, no need to expose
it outside of lio_main.c so declare it static and make sparse happy.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC register MRBLR defines the maximum space in
the RX buffers and is set to 1536 by gianfar. This
reasonably covers the common use case where the MTU
is kept at default 1500. In that case, the largest
Ethernet frame size of 1518 plus an optional
GMAC_FCB_LEN of 8, and an additional padding of 8
to handle FSL_GIANFAR_DEV_HAS_TIMER totals to 1534
and nicely fit within the chosen MRBLR.
Alas, if the eTSEC is attached to a DSA enabled switch,
the (E)DSA header extension (4 or 8 bytes) causes every
maximum sized frame to be fragmented by the hardware.
This patch increases the maximum RX buffer size by 8
and rounds up to the next multiple of 64, which the
hardware's defines as RX buffer granularity.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing console messages is not helpful when system is out of memory;
and can be disastrous with netconsole. Instead keep statistics
of these anomalous conditions.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
