For non-aggregated frames, ath9k was leaving handling of powersave
filtered packets to mac80211. This can be too slow if the intermediate
queue is already filled with packets and mac80211 does not immediately
send a new packet via drv_tx().
Improve response time with filtered frames by triggering clearing the
powersave filter internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It removes the need for undoing the padding changes to skb->data and it
improves performance by eliminating one tx status lookup per MPDU in the
status path. It is also useful for preparing a follow-up fix to better
handle powersave filtering.
A side effect is that these counters, available via debugfs, become now invalid:
* dot11TransmittedFragmentCount
* dot11FrameDuplicateCount,
* dot11ReceivedFragmentCount
* dot11MulticastReceivedFrameCount
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: add a note about counters, thanks to Zefir Kurtisi]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch corrects the revision id register and uses it along with
magic value and chip version registers to download appropriate firmware
image.
PCIe8997 Z chipset variant code has been removed, as it won't be used in
production.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch:
- improves code layout
- removes a useless memset(0) for some memory allocated with kzalloc
- removes a useless if. We know that 'if (chan_band_tlv)' will succeed
because it has been tested a few lines above
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements pre and post FLR handlers to support PCIe FLR
functionality. Software cleanup is performed in pre-FLR whereas
firmware is downloaded and software is re-initialised in
post-FLR handler.
Following command triggers FLR.
echo "1" > /sys/bus/pci/devices/$NUMBER/reset
This feature can be used as a recovery mechanism when firmware gets
hang.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_kso_control() there is a retry loop as hardware may take
time to settle. However, when the call to brcmf_sdiod_regrb() returns
an error it is due to SDIO access failure and it makes no sense to wait
for hardware to settle. This patch aborts the loop after a number of
subsequent access errors.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: Steve deRosier <derosier@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds cfg80211 testmode support so that userspace tools can
download necessary commands to firmware during manufacturing mode tests.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default normal mode is chosen when driver is loaded. This
patch adds a provision to choose manufacturing mode via module
parameters.
Below command loads driver in manufacturing mode
insmod mwifiex.ko mfg_mode=1.
Tested-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Be more strict about FW versions. Drop support for old
transitional revisions which were never used in production.
Dropping support for FW ABI version 0.0.0.0 is particularly
useful because 0 could just be uninitialized memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when reading global PFC statistics we left the counter
iterator out of the equation and we ended up reading the same counter
over and over again.
Instead of reading the counter at index 0 on every iteration we now read
the counter at index (i).
Fixes: e989d5a532 ('net/mlx5e: Expose flow control counters to ethtool')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64 bits architectures unsigned long is longer than u32,
casting to unsigned long will result in overflow.
We need to first allocate an unsigned long variable, then assign the
wanted value.
Fixes: 665bc53969 ('net/mlx5e: Use new ethtool get/set link ksettings API')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the xmit_more counter before notifying the HW,
to prevent a possible use-after-free of the skb.
Fixes: c8cf78fe10 ("net/mlx5e: Add ethtool counter for TX xmit_more")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MIPS based xilfpga platform uses this driver.
Enable it for MIPS
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device mac address is updated using ndo_set_mac_address(),
while the same mac address is already programmed, the driver does not
detect this condition if its netdev->dev_addr has been changed. The
driver tries to add the same mac address resulting in mac address
collision error. This has been observed in bonding mode-5 configuration.
To fix this, store the mac address configured in HW in the adapter
structure. Use this to compare against the new address being updated
to avoid collision.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a mac address is added to the uc_list and later the same mac address
is added via ndo_set_mac_address() or vice versa, the driver does not
detect this condition and tries to add it again. This results in a mac
address collision error when the FW rejects it.
Fix this by checking if the given mac address is present in uc_list while
setting the device mac address and vice versa. Similarly skip deletion if
the address is still in use in the other form.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver issues OPCODE_COMMON_GET_EXT_FAT_CAPABILITIES cmd during init which
when issued by VFs results in the logging of a cmd failure message since
they don't have the required privilege for this cmd. Fix by checking
privilege before issuing the cmd.
Also fixed typo in CAPABILITIES.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per SLI guideline, drivers need to issue COMMON_RESET_FUNCTION SLI
cmd during driver unload to clean up any non-persistent state
information.
Issue this cmd only if VFs are not assigned to VMs as it is possible
for PF driver to unload while it\'s VF remains functional and assigned
to a VM.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.
Following is the list of changes in the driver to support this:
o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.
o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).
o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.
o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.
o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.
o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.
o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems (such as the Qualcomm APQ8060 Dragonboard) the
RESET signal of the SMSC911x is not pulled up by a resistor (or
the internal pull-up that will pull it up if the pin is not
even connected) but instead connected to a GPIO line, so that
the operating system must explicitly deassert RESET before use.
Support this in the SMSC911x driver so this ethernet connector
can be used on such targets.
Notice that we request the line to go logical low (deassert)
whilst the line on the actual component is active low. This
is managed in the respective hardware description when
specifying the GPIO line with e.g. device tree or ACPI. With
device tree it looks like this in one case:
reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
Which means that logically requesting the RESET line to be
deasserted will result in the line being driven high, taking
the device out of reset.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_selftest.c:6:5: warning: no previous prototype for 'qed_selftest_memory' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:19:5: warning: no previous prototype for 'qed_selftest_interrupt' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:32:5: warning: no previous prototype for 'qed_selftest_register' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:55:5: warning: no previous prototype for 'qed_selftest_clock' [-Wmissing-prototypes]
In fact, these functions are declared in qed_selftest.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-meson glue driver supports Meson6 and Meson8 SoCs. Newer SoCs
are supported by the dwmac-meson8b driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Ethernet controller available in Meson8b and GXBB SoCs is a Synopsys
DesignWare MAC IP core which is already supported by the stmmac driver.
In addition to the standard stmmac driver some Meson8b / GXBB specific
registers have to be configured for the PHY clocks. These SoC specific
registers are called PRG_ETHERNET_ADDR0 and PRG_ETHERNET_ADDR1 in the
datasheet.
These registers are not backwards compatible with those on Meson 6b,
which is why a new glue driver is introduced. This worked for many
boards because the bootloader programs the PRG_ETHERNET registers
correctly. Additionally the meson6-dwmac driver only sets bit 1 of
PRG_ETHERNET_ADDR0 which (according to the datasheet) is only used
during reset.
Currently all configuration values can be determined automatically,
based on the configured phy-mode (which is mandatory for the stmmac
driver). If required the tx-delay and the mux clock (so it supports
the MPLL2 clock as well) can be made configurable in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
ath.git fixes for 4.8. Major changes:
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.
$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
text data bss dec hex filename
127817 27969 32800 188586 2e0aa drivers/net/ethernet/qlogic/qed/built-in.o.new
132474 27969 32800 193243 2f2db drivers/net/ethernet/qlogic/qed/built-in.o.old
Miscellanea:
o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build of m32r was giving warning:
In file included from drivers/net/ethernet/smsc/smc91x.c:92:0:
drivers/net/ethernet/smsc/smc91x.h:448:0: warning: "SMC_inb" redefined
#define SMC_inb(ioaddr, reg) ({ BUG(); 0; })
drivers/net/ethernet/smsc/smc91x.h:106:0:
note: this is the location of the previous definition
#define SMC_inb(a, r) inb(((u32)a) + (r))
drivers/net/ethernet/smsc/smc91x.h:449:0: warning: "SMC_outb" redefined
#define SMC_outb(x, ioaddr, reg) BUG()
drivers/net/ethernet/smsc/smc91x.h:108:0:
note: this is the location of the previous definition
#define SMC_outb(v, a, r) outb(v, ((u32)a) + (r))
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm still struggling to get this fix right..
Changes since v2:
- do not blindly modify SKB contents according to Dave's legitimate
objection
Changes since v1:
- dropped disabling HW checksum offload for Zynq
- initialize checksum similar to net/ethernet/freescale/fec_main.c
-- >8 --
MACB/GEM needs the checksum field initialized to 0 to get correct
results on transmit in all cases, e.g. on Zynq, UDP packets with
payload <= 2 otherwise contain a wrong checksums.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the preempt mode, the bpf_prog stored in xdp_prog may be
freed despite the use of call_rcu inside bpf_prog_put. The situation is
possible when running in PREEMPT_RCU=y mode, for instance, since the rcu
callback for destroying the bpf prog can run even during the bh handling
in the mlx4 rx path.
Several options were considered before this patch was settled on:
Add a napi_synchronize loop in mlx4_xdp_set, which would occur after all
of the rings are updated with the new program.
This approach has the disadvantage that as the number of rings
increases, the speed of update will slow down significantly due to
napi_synchronize's msleep(1).
Add a new rcu_head in bpf_prog_aux, to be used by a new bpf_prog_put_bh.
The action of the bpf_prog_put_bh would be to then call bpf_prog_put
later. Those drivers that consume a bpf prog in a bh context (like mlx4)
would then use the bpf_prog_put_bh instead when the ring is up. This has
the problem of complexity, in maintaining proper refcnts and rcu lists,
and would likely be harder to review. In addition, this approach to
freeing must be exclusive with other frees of the bpf prog, for instance
a _bh prog must not be referenced from a prog array that is consumed by
a non-_bh prog.
The placement of rcu_read_lock in this patch is functionally the same as
putting an rcu_read_lock in napi_poll. Actually doing so could be a
potentially controversial change, but would bring the implementation in
line with sk_busy_loop (though of course the nature of those two paths
is substantially different), and would also avoid future copy/paste
problems with future supporters of XDP. Still, this patch does not take
that opinionated option.
Testing was done with kernels in either PREEMPT_RCU=y or
CONFIG_PREEMPT_VOLUNTARY=y+PREEMPT_RCU=n modes, with neither exhibiting
any drawback. With PREEMPT_RCU=n, the extra call to rcu_read_lock did
not show up in the perf report whatsoever, and with PREEMPT_RCU=y the
overhead of rcu_read_lock (according to perf) was the same before/after.
In the rx path, rcu_read_lock is eventually called for every packet
from netif_receive_skb_internal, so the napi poll call's rcu_read_lock
is easily amortized.
v2:
Remove extra rcu_read_lock in mlx4_en_process_rx_cq body
Annotate xdp_prog with __rcu, and convert all usages to rcu_assign or
rcu_dereference[_protected] as appropriate.
Add explicit mutex lock around rcu_assign instead of xchg loop.
Fixes: d576acf0a2 ("net/mlx4_en: add page recycle to prepare rx ring for tx support")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
