Add definition of MTCAP and MTMP registers which provide access to
temperature sensors.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to flash the port's LED in order to identify it. This is
achieved by setting the Management LED Control Register (MLCR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MLCR register, which controls physical port identification LEDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive skb buffers can be preallocated when the link is opened
according to mtu size.
While testing on a network environment with not standard MTU (e.g. 3000),
a panic occurred if an incoming packet had a length greater than rx skb
buffer size. This is because the HW is programmed to copy, from the DMA,
an Jumbo frame and the Sw must check if the allocated buffer is enough to
store the frame.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stmmac_mdio_reset, was called from stmmac_resume, it was not
resetting the PHY due to which MAC was not getting reset properly and
hence ethernet interface not was resumed properly.
The issue was currently only reproducible on stih301-b2204.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the st,tx-retime-src is missing from device-tree
(it's an optional field) the driver will invoke the strcasecmp to check
which clock has been selected and this is a bug; the else condition
is needed.
In the dwmac_setup, the "rs" variable, passed to the strcasecmp, was not
initialized and the compiler, depending on the options adopted, could
take it in some different part of the stack generating the hang in such
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resume the HW is re-configured but some settings can be lost.
For example, the MAC Address_X High/Low Registers used for VLAN tagging..
So, while resuming, the set_filter callback needs to be invoked to
re-program perfect and hash-table registers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.
Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.
The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.
Fixes memory allocation errors on some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.
Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.
Fixes: 0a51b343ab ("ath10k: add board 2 API support")
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac_pton() converts 6-byte MAC / BSSID to binary format. Change an open coded
variant by the generic one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The original code returns 1 on failure and 0 on success but the caller
was expecting an error code on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"&card->priv->driver_lock" and "&priv->driver_lock" are the same and
it's nicer to use the shorter one consistently.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This code causes a static checker bug.
drivers/net/wireless/ralink/rt2x00/rt2500usb.c:232 _rt2500usb_register_read()
warn: passing casted pointer 'value' to 'rt2500usb_register_read()' 32 vs 16.
If the low 16 bits were initialized to zero then this code would only be
a problem on big endian systems. But in this case this is case the low
16 bits are never initialized. This is called from a function which is
created using a macro:
RT2X00DEBUGFS_OPS(csr, "0x%.8x\n", u32);
We end up copying uninitialized data to the user which is bogus and an
information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All bus drivers (sdio, usb and pcie) require firmware files which
needs to be downloaded to the device, The definitions and mapping
of device id and revision to firmware and nvram file is done by
each bus driver. This patch creates common functions and defines
to simplify and unify the definition of these firmware and nvram
files and mapping.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Under some kernel configuration we get build issue with implicit
declaration of net_ratelimit() function. Fix this by explicitly
including the file providing the prototype.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Aborting the current read attempt on the superframe also removes the
packet from the pipeline. Retries should not be attempted on the next
packet since it would not be a superframe(either a superframe descriptor
or other data packet) and should not be handled by brcmf_sdio_rxglom
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During initialization of the device, but also on some other
moments the driver prints an error that the netdev already exists.
This is a result of the way the driver is initializing the
firmware and not really an error. The code is not treating it as
an error either. This error print has resulted in many questions
by users and is confusing and incorrect. This patch changes the
error log into a debug info log.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FWIL is always mapping back errors to EBADE. This is not very
conventient when trying to understand problems by reading logs.
Some callers print the error code, but that is quite useless
when the exact error code is not returned. It also makes it
impossible to differentiate based on error code. This patch
changes the return of EBADE into the actual error code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On wcn3620, firmware response to remove_bsskey uses the new, larger
"v2" format
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On wcn3620, firmware response to trigger_ba uses the new, larger
"v2" format
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3620 has a new message structure for the reply to some hal
commands. This patch adds the struct and helper routine that
uses it if the chip is wcn3620, or falls back to the old
helper routine.
We don't know what to do with the candidate list he sends back,
but we can at least accept and ignore it nicely instead of dying.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3620 can asynchronously send two new kinds of indication message,
since we can't handle them just accept them quietly.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3620 firmware introduces a new async indication, we need to
add it as a known message type so we can accept it
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
Add vendor directories (for example intel, marvell and so on) to
drivers/net/wireless and change the menuconfig to follow the same
categorisation. This unifies the directory layout as we already had few drivers
already using vendor directories (especially ath and ti).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit cf4f21938e ("kbuild: Allow to specify composite modules
with modname-m"), thermal.c gets included in the driver and the build
fails with
drivers/net/wireless/ath/ath10k/thermal.c:119:6: error: redefinition of ‘ath10k_thermal_event_temperature’
drivers/net/wireless/ath/ath10k/thermal.h:54:20: note: previous definition of ‘ath10k_thermal_event_temperature’ was here
drivers/net/wireless/ath/ath10k/thermal.c:136:6: error: redefinition of ‘ath10k_thermal_set_throttling’
drivers/net/wireless/ath/ath10k/thermal.h:59:20: note: previous definition of ‘ath10k_thermal_set_throttling’ was here
drivers/net/wireless/ath/ath10k/thermal.c:162:5: error: redefinition of ‘ath10k_thermal_register’
drivers/net/wireless/ath/ath10k/thermal.h:45:19: note: previous definition of ‘ath10k_thermal_register’ was here
drivers/net/wireless/ath/ath10k/thermal.c:216:6: error: redefinition of ‘ath10k_thermal_unregister’
drivers/net/wireless/ath/ath10k/thermal.h:50:20: note: previous definition of ‘ath10k_thermal_unregister’ was here
Change the #ifdef to reflect the new kbuild behavior.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
The d0i3_mode element is never set to IWL_D0I3_OFF, so it's not
necessary to check it in iwl_mvm_is_d0i3_supported().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a potential race condition when entering suspend with d0i3 in
PCIe. If there is a frame queued just before we suspend, it won't
complete and we will never clear the queue stuck timer. To solve
this, call TX_PATH_FLUSH to flush all queues (except the command
queue) as part of the d0i3 entry process. Add a new function that
returns all the flushable queues.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the prph registers dump is in the transport layer,
and each bus needs an additional dump implementation.
Move the prph dump outside transport, and allow a common
implementation for all of the buses.
This is possible because prph base addresses are similar for
all buses.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Expose _no_grab prph i/o functions that allow performing i/o
outside the transport, without requiring grab and release NIC access
for each operation. In addition, rename the functions so they reflect
their non-grabbing behavior.
This can be very useful for consecutive prph i/o operation that occur
outside trans, such as fw dumps.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure. Remove it.
Fixes: dbb04b0d29 ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
