Driver gets country information from EEPROM during
initialization. We will call regulatory_hint to update
current regulatory domain.
As by default world regulatory domain is selected by
cfg80211, country '00' from EEPROM is ignored.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that even if firmware returns an error
for a configuration command, we go ahead and start AP.
This patch changes the command type from async to sync
so that threads waits for command response and return
failure start AP.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Even if ADHOC start or join attempt is failed, these commands
are returned with success status by firmware. Actual connection
result is provided inside command response.
This patch parses the adhoc connection result and resets
connection state variables if connection is not successful.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This code was supposed to trigger a BUG() if we truncate the output but
it's off by one so it allows one character to be truncated. Really
drivers shouldn't call BUG_ON() and especially for something minor like
this so I've changed it to a WARN_ON().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code returns success if prism2_init_local_data() fails, but
we want to return an error code. Also we can remove the bogus
ret initializer because it is wrong and never used.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already know that "wep_key->key_length" is set so there is no need to
check again. Also the last curly brace was indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This code causes a static checker warning because we check for
"if (ret == 0)" but we have already had verified that was true. Clean
it up a little.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the mode is NL80211_IFTYPE_UNSPECIFIED then we return success at the
start of the function so this condition is never true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a null ptr check for fws to set bcmc_credit_check, however,
there a lock and unlock on fws should only performed if fwts is
also not null to also avoid a potential null pointer deference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to new wl18xx sg parameters.
This requires to split both wl12xx/wl18xx enumerators.
Signed-off-by: Guy Mishol <guym@ti.com>
Acked-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kfree_skb() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull rdma fixes from Doug Ledford:
"Most are minor to important fixes.
There is one performance enhancement that I took on the grounds that
failing to check if other processes can run before running what's
intended to be a background, idle-time task is a bug, even though the
primary effect of the fix is to improve performance (and it was a very
simple patch)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Postpone remove_keys under knowledge of coming preemption
IB/mlx4: Use vmalloc for WR buffers when needed
IB/mlx4: Use correct order of variables in log message
iser-target: Remove explicit mlx4 work-around
mlx4: Expose correct max_sge_rd limit
IB/mad: Require CM send method for everything except ClassPortInfo
IB/cma: Add a missing rcu_read_unlock()
IB core: Fix ib_sg_to_pages()
IB/srp: Fix srp_map_sg_fr()
IB/srp: Fix indirect data buffer rkey endianness
IB/srp: Initialize dma_length in srp_map_idb
IB/srp: Fix possible send queue overflow
IB/srp: Fix a memory leak
IB/sa: Put netlink request into the request list before sending
IB/iser: use sector_div instead of do_div
IB/core: use RCU for uverbs id lookup
IB/qib: Minor fixes to qib per SFF 8636
IB/core: Fix user mode post wr corruption
IB/qib: Fix qib_mr structure
The cmac_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb90 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf2 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc69fdfc6c
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a106 ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WR headers may not fit within one descriptor.
So we need to deal with wrap-around here.
Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time. The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.
Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to iptunnel_xmit_stats() is not required after udp-tunnel6-xmit.
By calling iptunnel_xmit_stats() results in incorrect device stats.
Following patch drops this call.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ath9k_mod_tsf64_tu() function while we could
use div_u64_rem() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of MCC and AP interface, add also NOA attr
that will inform stations about absence of an AP.
There is a chance that some stations will handle
this NOA attr correctly and will know exactly when
AP is present/absent.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case we get BSS_CHANGED_P2P_PS early, from
mac80211, we didn't set NOA timer correctly,
while p2p_ps_vif was NULL.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding NOA attr enable Opportunistic Power Save.
Before we calculate ctwindow but didn't enable oppps.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After queue nullfunc for MCC case, we hit WARN_ON
in xmit.c:2398 while skb priority wasn't set.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AP/GO will aprear after NOA, wait 1ms to be sure AP
could receive/answer this frames.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While mac80211 using null frames when connection polling,
we should queue this frames while NOA could be there, and
AP, P2P_GO could be not present.
Without this patch, with no traffic we often saw disconnections
while we try to send nullfunc when AP/GO wasn't present.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of low HZ before this patch we saw wrong
values in debug message. Print real timeout value.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In __wmi_send we check if fw is ready at the beginning of the function.
While we wait for the completion of the previous command, system suspend
can be invoked and reset the HW, causing __wmi_send to read from HW
registers while it is not ready.
Taking the wmi_mutex in the reset flow when setting the FW ready bit
to zero will prevent the above race condition.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rates in the tx control rateset do not have the protection
flags applied, so RTS/CTS would never get enabled if requested.
Fix by using the rate flags in the rates returned by
ieee80211_get_tx_rates().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An error message ath6kl_htc_rxmsg_pending_handler isn't appropate for when
the error is ECANCELED. This could be the result of a perfectly appropriate
RX cancel due to shutdown or suspend. This allows the right cleanup to
continue, but without an alarming error message in this particular case.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The three eeprom implementations had quite some duplicate code when it
came to endianness swapping.
Additionally there was a bug in eeprom_4k and eeprom_9287 which
prevented the endianness swapping from working correctly, because the
swapping code was guarded within an "if (!ath9k_hw_use_flash(ah))". In
eeprom_def this check did not exist, so it seems that eeprom_def was the
only implementation where endianness swapping worked.
This patch takes the duplicate code and moves it from eeprom_* to
eeprom.c. The new code is derived from eeprom_def, while taking into
account the specifics from the other implementations.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
