The ks8995 phy driver just started using gpiod_* functions, which are
declared in linux/gpio/consumer.h, not linux/gpio.h, resulting in a
build failure in randconfig builds that do not have CONFIG_GPIOLIB
enabled:
drivers/net/phy/spi_ks8995.c: In function 'ks8995_probe':
drivers/net/phy/spi_ks8995.c:477:3: error: implicit declaration of function 'gpiod_set_value' [-Werror=implicit-function-declaration]
This changes the header inclusion so it builds in all configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cd6f288cba ("net: phy: spi_ks8995: add support for resetting switch using GPIO")
Signed-off-by: David S. Miller <davem@davemloft.net>
use generic dst implementation for both plain geneve devices and
lwtunnels.
In case of UDP traffic with datagram length below MTU this give
about 2% performance increase for plain geneve tunnel over ipv4,
about 65% performance increase for ipv6 tunnel.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 2% performance increase
when tunneling over ipv4 and about 60% when tunneling
over ipv6
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 3% performance increase
when tunneling over ipv4 and about 70% when
tunneling over ipv6.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several scenarios where taking a register dump from a device
might log benign GRC timeout attentions to system logs.
Most common of those is when taking the dump from a 2-port device.
Sadly, there's no easy way to mask the problematic attentions during the
flow - Changing this behvaior would require a firmware update.
For now, simply warn users to ignore the warnings.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is currently looking at shared information for determining whether
DCBx can be supported for a given port.
On 4-port devices, up-to-date management firmware can support DCBx on
each port of a given engine independently - but that would cause bnx2x to
misinterpert the support and assume DCBx is supported on both.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability to perform RSS hashing based on encapsulated
headers for a geneve-encapsulated packet.
This also changes the Vxlan implementation in bnx2x to be uniform
for both vxlan and geneve [from configuration perspective].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to MAC allocation requests to signify that the MAC VLAN filters
should come from the shared resource pool rather than the dedicated PF
resource pools.
Change-ID: I4c2da64c01856edcb0982bc4aab75c5a91047a7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Marvell 88E6240 has been tested successfully without further
changes. Add entry to the table of supported devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it. Reduce it to
511. The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx push is supported for small packets to reduce DMA latency. The
following bugs are fixed in this patch:
1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
20G is not supported by production hardware and only the 40GbaseCR4 standard
is supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.
In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change has been made with the goal that kernel functions should
return something more descriptive than -1 on failure.
A variable `err` has been introduced for storing error codes.
The return value of kzalloc on failure should return a -1 and not a
-ENOMEM. This was found using Coccinelle. A simplified version of
the semantic patch used is:
//<smpl>
@@
expression *e;
identifier l1;
@@
e = kzalloc(...);
if (e == NULL) {
...
goto l1;
}
l1:
...
return -1
+ -ENOMEM
;
//</smpl
Furthermore, set `err` to -ENOMEM on failure of alloc_netdev(), and to
-ENODEV on failure of register_netdev() and probe_irq_off().
The single call site only checks that the return value is not 0,
hence no change is required at the call site.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-02-15
This series contains updates to igb only.
Shota Suzuki cleans up unnecessary flag setting for 82576 in
igb_set_flag_queue_pairs() since the default block already sets
IGB_FLAG_QUEUE_PAIRS to the correct value anyways, so the e1000_82576
code block is not necessary and we can simply fall through. Then fixes
an issue where IGB_FLAG_QUEUE_PAIRS can now be set by using "ethtool -L"
option but is never cleared unless the driver is reloaded, so clear the
queue pairing if the pairing becomes unnecessary as a result of "ethtool
-L".
Mitch fixes the igbvf from giving up if it fails to get the hardware
mailbox lock. This can happen when the PF-VF communication channel is
heavily loaded and causes complete communications failure between the
PF and VF drivers, so add a counter and a delay so that the driver will
now retry ten times before giving up on getting the mailbox lock.
The remaining patches in the series are from Alex Duyck, starting with the
cleaning up code that sets the MAC address. Then refactors the VFTA and
VLVF configuration, to simplify and update to similar setups in the ixgbe
driver. Fixed an issue were VLANs headers size was being added to the
value programmed into the RLPML registers, yet these registers already
take into account the size of the VLAN headers when determining the
maximum packet length, so we can drop the code that adds the size to
the RLPML registers. Cleaned up the configuration of the VF port based
VLAN configuration. Also fixed the igb driver so that we can fully
support SR-IOV or the recently added NTUPLE filtering while allowing
support for VLAN promiscuous mode. Also added the ability to use the
bridge utility to add a FDB entry for the PF to an igb port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC could be disabled, while there is some sb_buff
in use. That buffers got lost for linux.
In order to reproduce run on device during active ethernet work:
ifconfig eth0 down
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedad ("net/mlx5e: Add support for SR-IOV ndos")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5e_select_queue is redundant since num_tc is always 1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also print an error message incase we do have to reconfigure as this
should no longer happen anymore due to ethtool changes. If it somehow
does occur, user should be made aware of it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex. The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.
It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex. This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex. This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.
This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.
This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae27 ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock. Later, the locking was changed to only hold RTNL, and so
after commit 876254ae27 ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: "Tantilov, Emil S" <emil.s.tantilov@intel.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: dingtianhong <dingtianhong@huawei.com>
Fixes: 876254ae27 ("bonding: don't call update_speed_duplex() under spinlocks")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222 ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a macro which helps adding new 40NM EPHY entries and reduces the
amount of boilerplate code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is BCM7xxx, we were missing an additional X in the constant naming,
fix that to be consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3b ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Fixes: 9458ceab49 ("net: phy: bcm7xxx: Add entry for BCM7435")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
Until this patch, when TXing non-sta the pending_frames counter
wasn't increased, but it WAS decreased in
iwl_mvm_rx_tx_cmd_single(), what makes it negative in certain
conditions. This in turn caused much trouble when we need to
remove the station since we won't be waiting forever until
pending_frames gets 0. In certain cases, we were exhausting
the station table even in BSS mode, because we had a lot of
stale stations.
Increase the counter also in iwl_mvm_tx_skb_non_sta() after a
successful TX to avoid this outcome.
CC: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There was a workaround partially implemented for the 82576 that is needed
in order for VLAN tag stripping to function correctly. The original code
had side effects that would make it so the workaround was active on all
MACs. I have updated the code so that the workaround is enabled, but
limited to the 82576, or activated if we exceed the available unicast
addresses.
The workaround has a side effect of mirroring all of the traffic outgoing
from the VFs back to the PF. As such it is not recommended to use the
82576 in promiscuous mode as it will take a performance hit, though this is
now consistent with the performance as seen on the out-of-tree igb driver.
I also limited the scope of the UTA bits all being set to only when the
VMOLR register is enabled. This should limit the effects of the UTA
register so that we don't pick up any excess traffic unless promiscuous
mode has been enabled on the PF, whereas before the PF would have ended up
in something equivalent to unicast promiscuous mode with VLAN filtering
otherwise.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the bridge utility to add a FDB
entry for the PF to an igb port. By doing this we can enable the VFs to
talk to virtual ports residing on top of the PF.
In addition this should also address issues with MACVLANs trying to reside
on top of the PF as well as they would have had similar issues when added
to the PF with SR-IOV enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops several checks that we dropped from ixgbe some ago. It
should not be possible for us to be called with either of the conditional
statements returning true so we can just drop them from the hot-path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes things so that we can fully support SR-IOV or the
recently added NTUPLE filtering while allowing support for VLAN promiscuous
mode. By making this change we are able to support possible scenarios such
as SR-IOV with the PF connected to a Linux bridge hosting other VMs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean-up the configuration of the VF port based VLAN
configuration. The original logic was a bit muddled and had some
undesirable side effects such as VLANs being either completely stripped
from the port or VLANs being left when they shouldn't be. The idea behind
this code is to avoid any events such as spurious spoof notifications when
we are removing one VLAN tag and replacing it with another.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can merge the configuration of the VLVF
registers into the setting of the VFTA register. By doing this we simplify
the logic and make use of similar functionality that we have already added
for ixgbe making it easier to maintain both drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that we always add VLAN 0. This is important as we
need to guarantee the PF can receive untagged frames in the case of SR-IOV
being enabled but VLAN filtering not being enabled in the kernel.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RLPML registers already take the size of VLAN headers into account when
determining the maximum packet length. This is called out in EAS documents
for several parts including the 82576 and the i350. As such we can drop
the addition of size to the value programmed into the RLPML registers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
