Commit Graph

64688 Commits

Author SHA1 Message Date
Liad Kaufman
280452c905 iwlwifi: mvm: disable DQA support
Do not allow entrance into DQA flows until feature is
completely ready and merged.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2016-03-02 08:58:24 +02:00
Sara Sharon
5eae443eb5 iwlwifi: pcie: detect and workaround invalid write ptr behavior
In 9000 series A0 step the closed_rb_num is not wrapping around
properly. The queue is wrapping around as it should, so we can
W/A it by wrapping the closed_rb_num in the driver.
While at it, extend RX logging and add error handling of other
cases HW values may cause us to access invalid memory locations.
Add also a proper masking of vid value read from HW - this should
not have actual affect, but better to be on the safe side.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2016-03-02 08:57:51 +02:00
Chaya Rachel Ivgi
fcb6b92a68 iwlwifi: mvm: update ucode status before stopping device
Leaving ucode_loaded to true after stop_device() has been called
is a recipe for problems. Flows that are not sync'ed with the
driver life cycle (like debugfs hooks and thermal hooks) must
check that the firmware is loaded before they interact with it.
Therefore we need to keep this variable updated with the real
status of the firmware.

Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2016-03-02 08:56:58 +02:00
Yuval Mintz
b4149dc7e1 qed: Print additional HW attention info
This patch utilizes the attention infrastructure to log additional
information that relates only to specific HW blocks.
For some of those HW blocks, it also stops automatically disabling the
attention generation as the attention is considered benign and thus
should only be logged; No fear of it flooding the system.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:39:50 -05:00
Yuval Mintz
ff38577aa9 qed: Print HW attention reasons
Each HW block contains common information about attention reasons,
raising a bit for each one of the different sub-reasons that caused it
to raise an attention.

This patch extends the infrastructure by allowing logging of the various
reasons causing the HW blocks to generate an attention.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:39:50 -05:00
Yuval Mintz
0d956e8a65 qed: Add support for HW attentions
HW is capable of generating attentnions for a multitude of reasons,
but current driver is enabling attention generation only for management
firmware [required for link notifications].

This patch enables almost all of the possible reasons for HW attentions,
logging the HW block generating the attention and preventing further
attentions from that source [to prevent possible attention flood].
It also lays the infrastructure for additional exploration of the various
attentions.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:39:50 -05:00
Yuval Mintz
4ac801b77e qed: Semantic refactoring of interrupt code
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:39:49 -05:00
Moshe Lazer
0ba422410b net/mlx5: Fix global UAR mapping
Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.

Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).

Caller will now have to choose whether to map via
write-combining API or not.

mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.

Fixes: 88a85f99e5 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:28:00 -05:00
Gal Pressman
2fcb92fbd0 net/mlx5e: Don't modify CQ before it was created
Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.

Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:28:00 -05:00
Gal Pressman
7524a5d88b net/mlx5e: Don't try to modify CQ moderation if it is not supported
If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.

Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:28:00 -05:00
Tariq Toukan
556dd1b9c3 net/mlx5e: Set drop RQ's necessary parameters only
By its role, there is no need to set all the other parameters
for the drop RQ.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:27:59 -05:00
Tariq Toukan
c89fb18b65 net/mlx5e: Move common case counters within sq_stats struct
For data cache locality considerations, we moved the nop and
csum_offload_inner within sq_stats struct as they are more
commonly accessed in xmit path.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:27:59 -05:00
Tariq Toukan
3b6195240c net/mlx5e: Changed naming convention of tx queues in ethtool stats
Instead of the pair (channel, tc), we now use a single number that
goes over all tx queues of a TC, for all TCs.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:27:59 -05:00
Tariq Toukan
ce89ef36d2 net/mlx5e: Placement changed for carrier state updates
More proper to declare carrier state UP only after the channels
are ready for traffic.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:27:59 -05:00
Tariq Toukan
daa21560a2 net/mlx5e: Replace async events spinlock with synchronize_irq()
We only need to flush the irq handler to make sure it does not
queue a work into the global work queue after we start to flush it.
So using synchronize_irq() is more appropriate than a spin lock.

Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:27:58 -05:00
David S. Miller
d67703fced Merge tag 'mac80211-next-for-davem-2016-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:

====================
Here's another round of updates for -next:
 * big A-MSDU RX performance improvement (avoid linearize of paged RX)
 * rfkill changes: cleanups, documentation, platform properties
 * basic PBSS support in cfg80211
 * MU-MIMO action frame processing support
 * BlockAck reordering & duplicate detection offload support
 * various cleanups & little fixes
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 17:03:27 -05:00
Alexandre Belloni
99f81afc13 phy: micrel: Disable auto negotiation on startup
Disable auto negotiation on init to properly detect an already plugged
cable at boot.

At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.

It was working properly before 321beec504 (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.

Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:52:09 -05:00
Alexandre Belloni
f5aba91d7f phy: micrel: Ensure interrupts are reenabled on resume
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.

This fixes resuming which is failing on the xplained boards from atmel
since 321beec504 (net: phy: Use interrupts when available in NOLINK
state)

Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:52:08 -05:00
Arnd Bergmann
a1cbaad75a asm-generic: remove old nonatomic-io wrapper files
The two header files got moved to include/linux, and most
users were already converted, this changes the remaining drivers
and removes the files.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
2016-03-01 22:25:17 +01:00
Vivien Didelot
214cdb9987 net: dsa: mv88e6xxx: support VLAN filtering
Implement port_vlan_filtering in the driver to toggle the related port
802.1Q mode between DISABLED and SECURE, on user request.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:53 -05:00
Vivien Didelot
46fbe5e5af net: dsa: mv88e6xxx: remove reserved VLANs
Now that ports isolation is correctly configured when joining or leaving
a bridge, there is no need to rely on reserved VLANs to isolate
unbridged ports anymore. Thus remove them, and disable 802.1Q on setup.

This restores the expected behavior of hardware bridging for systems
without 802.1Q or VLAN filtering enabled.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:53 -05:00
Vivien Didelot
b7666efe46 net: dsa: mv88e6xxx: restore VLANTable map control
The In Chip Port Based VLAN Table contains bits used to restrict which
output ports this input port can send frames to.

With the VLAN filtering enabled, these tables work in conjunction with
the VLAN Table Unit to allow egressing frames.

In order to remove the current dependency to BRIDGE_VLAN_FILTERING for
basic hardware bridging to work, it is necessary to restore a fine
control of each port's VLANTable, on setup and when a port joins or
leaves a bridge.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:52 -05:00
Vivien Didelot
466dfa0770 net: dsa: mv88e6xxx: assign dynamic FDB to bridges
Give a new bridge a fresh FDB, assign it to its members, and restore a
fresh FDB to a port leaving a bridge.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:52 -05:00
Vivien Didelot
2db9ce1fd9 net: dsa: mv88e6xxx: assign default FDB to ports
Restore per-port FDB. Assign them on setup, allow adding and deleting
addresses into them, and dump them.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:52 -05:00
Vivien Didelot
3285f9e869 net: dsa: mv88e6xxx: assign dynamic FDB to VLANs
Add a _mv88e6xxx_fid_new function which gives and flushes the lowest FID
available. Call it when preparing a new VTU entry.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:52 -05:00
Vivien Didelot
74b6ba0d76 net: dsa: mv88e6xxx: extract single FDB dump
Move out the code which dumps a single FDB to its own function.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:52 -05:00
Vivien Didelot
2fb5ef09de net: dsa: mv88e6xxx: extract single VLAN retrieval
Rename _mv88e6xxx_vlan_init in _mv88e6xxx_vtu_new, eventually called
from a new _mv88e6xxx_vtu_get function, which abstracts the VTU GetNext
VID-1 trick to retrieve a single entry.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:24:51 -05:00
Guillaume Nault
edffc2178d ppp: lock ppp->flags in ppp_read() and ppp_poll()
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl().
In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update
ppp->flags while ppp_read() or ppp_poll() is reading it.
The update done by ppp_ccp_closed() isn't atomic due to the bit mask
operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent
readers might get transient values.
Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC'
test in ppp_read() and ppp_poll(), which in turn can lead to improper
decision on whether the PPP unit file is ready for reading or not.

Since ppp_ccp_closed() is protected by the Rx and Tx locks (with
ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll()
to guarantee that ppp_ccp_closed() won't update ppp->flags
concurrently.

The same reasoning applies to ppp->n_channels. The 'n_channels' field
can also be written to concurrently by ppp_ioctl() (through
ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't
atomic (simple increment/decrement), but are protected by both the Rx
and Tx locks (like in the ppp->flags case). So holding the Rx lock
before reading ppp->n_channels also prevents concurrent writes.

Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:15:07 -05:00
Ido Schimmel
18f1e70c41 mlxsw: spectrum: Introduce port splitting
Allow a user to split or unsplit a port using the newly introduced
devlink ops.

Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:31 -05:00
Ido Schimmel
a133318cde mlxsw: spectrum: Mark unused ports using NULL
When splitting and unsplitting we'll destroy usable ports on the fly, so
mark them using a NULL pointer to indicate that their local port number
is free and can be re-used.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:30 -05:00
Ido Schimmel
558c2d5e52 mlxsw: spectrum: Store local port to module mapping during init
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.

When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.

When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.

Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:30 -05:00
Ido Schimmel
3e9b27b8fc mlxsw: spectrum: Unmap local port from module during teardown
When splitting a port we replace it with 2 or 4 other ports. To be able
to do that we need to remove the original port netdev and unmap it from
its module. However, we first mark it as disabled, as active ports
cannot be unmapped.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:30 -05:00
Jiri Pirko
284ef80357 mlxsw: core: Add devlink port splitter callbacks
Add middle layer in mlxsw core code to forward port split/unsplit calls
into specific ASIC drivers.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:30 -05:00
Jiri Pirko
c4745500e9 mlxsw: Implement devlink interface
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:30 -05:00
Jiri Pirko
b2facd95ab mlx4: Implement port type setting via devlink interface
So far, there has been an mlx4-specific sysfs file allowing user to
change port type to either Ethernet of InfiniBand. This is very
inconvenient.

Allow to expose the same ability to set port type in a generic way
using devlink interface.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:29 -05:00
Jiri Pirko
09d4d087cd mlx4: Implement devlink interface
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:07:29 -05:00
John Fastabend
2b6ab0d3aa net: cls_u32: move TC offload feature bit into cls_u32 offload logic
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.

This patch lifts the check into the core code and removes it from the
driver specific case.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 16:05:39 -05:00
Paolo Abeni
163e529200 veth: implement ndo_set_rx_headroom
The rx headroom for veth dev is the peer device needed_headroom.
Avoid ping-pong updates setting the private flag IFF_PHONY_HEADROOM.

This avoids skb head reallocation when forwarding from a veth dev
towards a device adding some kind of encapsulation.

When transmitting frames below the MTU size towards a vxlan device,
this gives about 10% performance speed-up when OVS is used to connect
the veth and the vxlan device and a little more when using a
plain Linux bridge.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:54:31 -05:00
Paolo Abeni
eaea34b23c net/tun: implement ndo_set_rx_headroom
ndo_set_rx_headroom controls the align value used by tun devices to
allocate skbs on frame reception.
When the xmit device adds a large encapsulation, this avoids an skb
head reallocation on forwarding.

The measured improvement when forwarding towards a vxlan dev with
frame size below the egress device MTU is as follow:

vxlan over ipv6, bridged: +6%
vxlan over ipv6, ovs: +7%

In case of ipv4 tunnels there is no improvement, since the tun
device default alignment provides enough headroom to avoid the skb
head reallocation.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:54:30 -05:00
Michael Chan
90e2092130 bnxt_en: Add hwrm_send_message_silent().
This is used to send NVM_FIND_DIR_ENTRY messages which can return error
if the entry is not found.  This is normal and the error message will
cause unnecessary alarm, so silence it.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:02 -05:00
Michael Chan
fbfbc4851d bnxt_en: Refactor _hwrm_send_message().
Add a new function bnxt_do_send_msg() to do essentially the same thing
with an additional paramter to silence error response messages.  All
current callers will set silent to false.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:02 -05:00
Rob Swindell
3ebf6f0a09 bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO
For everything to fit, we remove the PHY microcode version and replace it
with the firmware package version in the fw_version string.

Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:01 -05:00
Michael Chan
a8643e1604 bnxt_en: Fix dmesg log firmware error messages.
Use appropriate firmware request header structure to prepare the
firmware messages.  This avoids the unnecessary conversion of the
fields to 32-bit fields.  Add appropriate endian conversion when
printing out the message fields in dmesg so that they appear correct
in the log.

Reported-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:01 -05:00
Michael Chan
ff4fe81d2d bnxt_en: Use firmware provided message timeout value.
Before this patch, we used a hardcoded value of 500 msec as the default
value for firmware message response timeout.  For better portability with
future hardware or debug platforms, use the value provided by firmware in
the first response and store it for all susequent messages.  Redefine the
macro HWRM_CMD_TIMEOUT to the stored value.  Since we don't have the
value yet in the first message, use the 500 ms default if the stored value
is zero.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:01 -05:00
Michael Chan
dfc9c94a83 bnxt_en: Add coalescing support for tx rings.
When tx and rx rings don't share the same completion ring, tx coalescing
parameters can be set differently from the rx coalescing parameters.
Otherwise, use rx coalescing parameters on shared completion rings.

Adjust rx coalescing default values to lower interrupt rate.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:01 -05:00
Michael Chan
bb053f52a5 bnxt_en: Refactor bnxt_hwrm_set_coal().
Add a function to set all the coalescing parameters.  The function can
be used later to set both rx and tx coalescing parameters.

v2: Fixed function parameters formatting requested by DaveM.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:00 -05:00
Michael Chan
dfb5b894f8 bnxt_en: Store irq coalescing timer values in micro seconds.
Don't convert these to internal hardware tick values before storing
them.  This avoids the confusion of ethtool -c returning slightly
different values than the ones set using ethtool -C when we convert
hardware tick values back to micro seconds.  Add better comments for
the hardware settings.

Also, rename the current set of coalescing fields with rx_ prefix.
The next patch will add support of tx coalescing values.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:00 -05:00
Jeffrey Huang
1924136844 bnxt_en: Send PF driver unload notification to all VFs.
During remove_one() when SRIOV is enabled, the PF driver
should broadcast PF driver unload notification to all
VFs that are attached to VMs. Upon receiving the PF
driver unload notification, the VF driver should print
a warning message to message log.  Certain operations on the
VF may not succeed after the PF has unloaded.

Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:00 -05:00
Jeffrey Huang
3874d6a8b6 bnxt_en: Improve bnxt_vf_update_mac().
Allow the VF to setup its own MAC address if the PF has not administratively
set it for the VF.  To do that, we should always store the MAC address
from the firmware.  There are 2 cases:

1. The MAC address is valid.  This MAC address is assigned by the PF and
it needs to override the current VF MAC address.

2. The MAC address is zero.  The VF will use a random MAC address by default.
By storing this 0 MAC address in the VF structure, it will allow the VF
user to change the MAC address later using ndo_set_mac_address() when
it sees that the stored MAC address is 0.

v2: Expanded descriptions and added more comments.

Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:37:00 -05:00
Ivan Vecera
a7f4b98896 bna: fix list corruption
Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.

Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01 15:19:43 -05:00