All the disable_rf() functions were setting REG_TXPAUSE to 0xff to
stop transmission. Do it centrally before calling disable_rf()
instead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements an 8192eu specific enable_rf() function. The 8192eu is
not a combo device, so no need for doing the BT specific bits needed
by the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver relies on driver_info in struct usb_device_id, so allowing
adding a device via /sys/bus/usb/drivers/rtl8xxxu/new_id will cause a
NULL pointer dereference.
Set .no_dynamic_id = 1 to disable hot add of USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8188RU does not like PAPE to be enabled, while all the other gen1
parts seem to require it.
This makes the RTL8188RU able to associate for me.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This register is undocumented in the vendor code, but it is set
unconditionally for all 8192cu/8188cu/8188ru parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a long standing bug where mac80211 would send disconnect
packets to the device, after we had shut down the device.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In particular set APS_FSMCO_WLON_RESET in the right register, and do
not overwrite too much of REG_CR.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch was being missed since rtl_chip will never match RTL8188C
if hi_pa is true.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the vendor driver, devices with an external PA needs limiting it's
TX power to 0x20.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Load the RF table in init_phy_rf(), which allows for applying device
specific RF hacks in the same place. Getting rid of more ugly if ()
clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
several functions are not initializing a return status in ret
resulting in garbage to be returned instead of 0 for success.
Currently, the calls to these functions are not checking the
return, however, it seems prudent to return the correct status
in case they are to be checked at a later date.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes an unneeded hack for 8192eu, and allows for initializing
REG_FPGA0_XAB_RF_SW_CTRL at the same point as it is done for all other
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes a bunch of if () spaghetti and re-applies the USB bus
quirks for 8188/8192 that had gotten lost.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rather than scattering the code with #ifdefs, use the fileops
structure to hold device specific PBP values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was expired by the vendor driver, but we never ended up using the
backed up value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the loading of the AGC table into init_phy_bb() and reduces
the if() clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This should get the order right and avoid patching something that is
later overwritten.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reduces the if () clutter. Longer term it probably makes sense to
split this between gen1 (8723au/8188cu/8192cu) and gen2
(8192eu/8723bu) devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old code incorrectly wiped out bits 0-23 by mistake when setting
the RX path for 1T parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No actual code flow change, but no need to warn about something that
isn't a prioblem.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This caught a bug where too little memory was allocated for RX urbs
for parts using 24 byte RX descriptors
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This shouldn't affect little endian system, but may have prevented the
driver working on big endian systems for devices with the larger 24
byte RX descriptors.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead use tx_desc_size() to distinguish between gen1
(8723a/8192c/8188c) and gen2 (8723b/8192e) parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8192eu is a 2T part, so setting TX power for path A only, as done by
rtl8723bu_set_tx_power() is not sufficient.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like the 8723bu, the vendor driver does not set FPGA0_TX_INFO for
8192eu in the init sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vendor driver does not set REG_PBP on 8192eu. Whether this is due
to the device not supporting it or simply an oversight in the vendor
driver is not clear.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Longer term we should switch all the chips over to use this function
instead of the random chip specific ifdef hacks.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This further reorganizes the init code flow to match that of the
8192eu vendor driver. This helps diffing the register write log
against that of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to debug 8192eu support, reorder some init code to match the
flow of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
after factoring out mwifiex_cancel_pending_scan_cmd
the function is not called outside of cmdevt file
moved function to head of file to avoid forward declaration,
also moved mwifiex_recycle_cmd_node since they are very similar
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Releasing the scan_pending lock in mwifiex_check_next_scan_command
introduces a short window where pending scan commands can be removed
or added before removing them all in mwifiex_cancel_pending_scan_cmd.
I think this is safe, since the worst thing to happen is that a
pending scan cmd is removed by the command handler. Adding new scan
commands is not possible while one is pending, see scan_processing flag.
Since all commands are removed from the queue anyway, we don't care if
some commands are removed by a different code path earlier, the final
state remains the same.
I assume, that the critical section needed for the check has been
extended over clearing the pending scan queue out of convenience. The
lock was already held and releasing it and grab it again was just
more work. It doesn't seem to be necessary because of concurrency.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
given this structure:
struct foo {
struct bar {
int baz;
}
}
these accesses are equivalent:
(*(foo->bar)).baz
foo->bar->baz
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add scatterlist support (dev_coredumpsg) to allow drivers to avoid
vmalloc() like dev_coredumpm(), while also avoiding the module
reference that the latter function requires.
This internally uses dev_coredumpm() with function inside the
devcoredump module, requiring removing the const
(which touches the driver using it.)
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
by moving common code to ar5008_hw_cmn_spur_mitigate i forgot to move
mask_m & mask_p initialisation. This coused a performance regression
on ar9281.
Fixes: f911085ffa ("ath9k: split ar5008_hw_spur_mitigate and reuse common code in ar9002_hw_spur_mitigate.")
Reported-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Tested-by: Gustav Frederiksen <lkml2017@openmailbox.org>
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
