SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
replace REG_WRITE to REG_RMW and place every thing in one
RMW buffer.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
it is possible to reduce time needed for this function
by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands
in same buffer.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function uses mixed styles for register names/numbers which
is make harder reading and optimisation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.
In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Seems H/W report correctly firmware Autorun value only at initialization
stage. When we close interface and open it again, Autorun value is 0 and
we try to load firmware what kills the device. To fix clear
REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we
discover Autorun mode.
Reported-and-tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b mac80211: initialize rate control earlier for tdls station
Firmware 10.2.4.48-3 now supports management frames over HTT feature and has
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX. But as 10.2.4 branch has conflicting HTT ids
patch "ath10k: add ATH10K_FW_IE_HTT_OP_VERSION" is needed to fix the issue.
Older ath10k versions don't have support that support and to maintain backwards
compatibility we need bump up the FW API to 5 not break older versions.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Target to host HTT messages are conflicting between 10.x and other
firmware revisions. By maintaining separate HTT T2H tables for each
firmware revisions (main, 10x and tlv) similar to WMI abstraction,
solves the conflicts. Add ATH10K_FW_IE_HTT_OP_VERSION so that the firmware can
advertise the HTT interface to ath10k.
This fix is needed to get management frames over HTT (ie.
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX disabled) working with 10.2.4.48-2 firmware.
Otherwise there will be unknown htt events and nothing works:
[30087.438343] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30087.448691] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30149.032974] ath10k_pci 0000:02:00.0: htt event (19) not handled
If the firmware does not have ATH10K_FW_IE_HTT_OP_VERSION use the main HTT
interface. That way old firmware images will still work.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the reset flow, the driver cancels ongoing scan and sends scan
complete notification to mac80211. However it does not clean its UID.
Add cleaning scan UID for the ongoing scan. Loop over all other UIDs
to make sure there's nothing left there and warn if any is found.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a strong relationship between the NVM version and
the hardware step. Enforce that in the driver in case the
default NVM on the platform is the wrong one.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes we will want to configure the timeouts for the
Tx queues based on the vif type. Allow to do that using the
trigger mechanism.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to implement the enable_scan_iteration_notif handling
explicitly and there's no reason not to export the current value. So
use debugfs_create_bool() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for delaying the start of a scheduled scan (or a WoWLAN
net-detect scan).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ref_count is currently initialized on start_fw(). This causes
some issues in restart flow, as currently active references
(e.g. unclaimed command) will get cleared, resulting in
invalid reference accounting.
Move the ref_count initialization to the configure() trans op,
so it won't be re-initialized on restart.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The AP_START d0i3 reference was never removed if the AP started correctly.
This has the unpleasant side-effect of preventing D0i3 on Android if the
WiFi hotspot was ever started on the device.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi:
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have wlcore device-tree bindings in place
(for both wl12xx and wl18xx), remove the legacy
wl12xx_platform_data struct, and move its members
into the platform device data (that is passed to wlcore)
Davinci 850 is the only platform that still set
the platform data in the legacy way (and doesn't
have DT bindings), so remove the relevant
code/Kconfig option from the board file (as suggested
by Sekhar Nori)
Since no one currently uses wlcore_spi, simply remove its
platform data support (DT bindings will have to be added
if someone actually needs it)
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead. Also add a
boolean to specify whether the clock is XTAL or not.
Change all board files to reflect this.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - small fixes, update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In this routine, kzalloc allocates a memory block. This allocation is
freed in the error paths, but not in the normal exit, thus the allocation
is leaked.
The kmemleak facility was used to find the leak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since thermal daemon is unaware of the device state, it might
try to adjust the throttle state when the device is powered down.
So the driver caches the value and will configure it while
powering up the target. The cached value will be programed later
once the device is brought up. In such case, returning error
status is confusing and misleading the user application. Hence
moving the driver state check before sending wmi command to target.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
