Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since commit cd6cfd7311
"ath9k: do not set half/quarter channel flags in AR_PHY_MODE" the
condition "rfMode & (AR_PHY_MODE_QUARTER | AR_PHY_MODE_HALF)" would
never evaluate to true.
Fix this by using the available IS_CHAN_HALF_RATE and IS_CHAN_QUARTER_RATE
marcros instead.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to keep the same for loop twice in the code.
Move the txpower cap before the loop to reduce code complexity.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since ATH9K_TX99 depends on ATH9K_DEBUGFS anyway move it there
such that "make menuconfig" will indent TX99 support below ath9k
debugging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The same functionality as ar9003_hw_tx_power_regwrite is hardcoded in
ar9003_hw_tx99_set_txpower. Just reuse the existing ar9003_hw_tx_power_regwrite
for TX99 setup too.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).
To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec, VHT doesn't exist in 2.4GHz.
There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.
Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).
To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.
The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.
To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
With two different h2c_cmd() functions, mbox_ext_reg and
mbox_ext_width are no longer needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename it to rtl8xxxu_gen2_prepare_calibrate() and remove the calls to
it from rtl8xxxu_gen1_phy_iq_calibrate()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The H2C API is completely different between gen1 and gen2 parts, so
there is little point trying to treat this as a generic function. All
calls to *_h2c_cmd() will always come from a gen1 or a gen2 specific
function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic to most of the chips, so change the name to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic for most (if not all) gen1 parts, so rename
it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is nothing 8723au specific about this function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the code for rtl8188c, rtl8188r, and rtl8192c into it's own
file. This is purely a code moving exercise, there is no change to the
code itself.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8723a code into it's own file. This is purely a code
moving exercise, no code changes.
This device specific file is a lot smaller since the gen1 chips
(8723a, 8188c, 8188r, 8192c) share a lot more common code than the
gen2 chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8723b code into it's own file. This is purely a code
moving exercise, no functional changes. This did expose
rtl723a_h2c_cmd() as a function that should be refactored into a gen1
and a gen2 version.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8192e code into it's own file. This is purely a code
moving exercise, no code changes.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames the core file to rtl8xxxu_core.c in order to allow us to
keep the module nake rtl8xxxu.ko when refactoring the code into
multiple files.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl818x_ioread8_idx: 151 bytes, 29 calls
rtl818x_ioread16_idx: 151 bytes, 11 calls
rtl818x_ioread32_idx: 151 bytes, 5 calls
rtl818x_iowrite8_idx: 157 bytes, 117 calls
rtl818x_iowrite16_idx: 158 bytes, 74 calls
rtl818x_iowrite32_idx: 157 bytes, 22 calls
Each of these functions has a pair of mutex lock/unlock ops,
both of these ops perform atomic updates of memory (on x86, it boils down to
"lock cmpxchg %reg,mem" insn), which are 4-8 times more expensive than call+return.
text data bss dec hex filename
95894242 20860288 35991552 152746082 91ab862 vmlinux_before
95872674 20860320 35991552 152724546 91a6442 vmlinux
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: Chaoming Li <chaoming_li@realsil.com.cn>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
brcmfmac
* add support for nl80211 BSS_SELECT feature
mwifiex
* add platform specific wakeup interrupt support
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that sometimes AP's probe response is
received after scan duration gets completed for the channel.
This happens especially when wildcard scan is performed
along with specific SSID scan.
We will increase the time from 30 msecs to 40 msecs.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 2.4Ghz channels are overlapping, sometimes AP responds to
probe request even if it's operating on neighbouring channel.
Currently firmware drops those scan entries, as current channel
doesn't match with APs channel.
This patch enables MWIFIEX_DISABLE_CHAN_FILT flag in scan
command to disable the feature so that better scan results
will be received in 2.4Ghz band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In cfg80211 resume handler, we query wakeup reason from firmware and
report to cfg80211. if wowlan is disabled, connection is already
terminated during suspend. We don't need to query wakeup reason in this
case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that wakeup on GTK rekey failure wasn't reported
to cfg80211. This patch corrects the check so that all valid wakeup
reasons are reported.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
tx_packets counter is incremented for aggregated packets, when it had
already been incremented for the aggregated packet's constituent
parts. Removing the extra count.
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a packet is queued from the bridge, wmm_tx_pending is not
incremented, but when the packet is dequeued the counter is decremented.
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After booting the wireless subsystem and uploading the NV blob to the
WCNSS_CTRL service the remote continues to do things and will not start
servicing wlan-requests for another 2-5 seconds (measured).
The downstream code does not have any special handling for this case,
but has a timeout of 10 seconds for the communication layer. By
extending the wcn36xx timeout to match this we follows the same flow for
the boot procedure and can successfully configure WiFi as wlan0 is
registered.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In idle times 60G device can enter deep sleep and turn off
its XTAL clock.
Host access triggers the device power-up flow which will hold
the AHB during XTAL stabilization until device switches from
slow-clock to XTAL clock.
This behavior can stall the PCIe bus for some arbitrary period
of time.
In order to prevent this stall, host can vote for High Latency
Access Policy (HALP) before reading from PCIe bus.
This vote will wakeup the device from deep sleep and prevent
deep sleep until unvote is done.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
RX_HTRSH interrupt sometimes triggered during device reset
procedure.
To prevent handling this interrupt when not required, unmask
this interrupt only if we are connected and mask it when
disconnected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Network stack can try to transmit data while AP / STA is
disconnected.
Change this print-out to debug level as this should not be
handled as error.
This patch also adds wil_dbg_ratelimited, used to limit the
above print-out.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using interrupt moderation RX_HTRSH interrupt can occur
frequently during high throughput and should not be considered
as error.
Such print-outs can degrade the performance hence should be printed
in debug print level.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
P2P search can only run on the social channel (channel 2).
When issuing a scan request on the P2P_DEVICE interface,
driver ignored the channels argument and always performed a P2P
search.
Fix this by checking the channels argument, if it is
not specified (meaning full scan) or if a non-social channel
was specified, perform a regular scan and not a P2P search.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's useful to permit the customization of the debug uart baud rate. Enable
this and send down the value to the chip if we're enabling debug.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
