This allows RSN pre-authentication to be used when roaming decisions are
done in the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. This might lead to a race condition where both may try
to connect to some AP based on their scan results.
Since the firmware is capable of handling roaming, let
wpa_supplicant know about this capability so that it will back off
from bgscan based roaming.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since we may end up using a dummy BSS entry when roaming, allow one Beacon
frame -based bssinfo from the current BSS to be processed prior to starting
to filter all bssinfo events. This allows cfg80211 BSS table to be filled
with proper data in the roaming case where the full Beacon data may not
have been present at the time of roamed event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no point in unconditionally converting the bssinfo header
to the old version since only the new header is being used and the
driver can as well read the values from it when needed. Leaving out
the conversion saves some extra memory copying.
In addition, use the calculated "rssi" value snr - 95 dBm to get the
proper value in cfg80211 BSS table (i.e., something that more or less
matches with the value used in STA info).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that the scan results are reported directly to the cfg80211 BSS
table there is no need for maintaining this internal node table
implementation for scan results. Remove the definitions and node
table functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal node table in ath6kl was not really used for any useful
purpose. It was just used to collect scan results during a scan and then
provide them in a burst to cfg80211 at the completion of the scan. There
is no point in doing this since cfg80211 is perfectly capable of
maintaining the BSS table and the BSS inform messages are sent in
separate function calls anyway.
This provides more complete information in the cfg80211 BSS table since
this allows Beacon and Probe Response frames to be distinguished and IEs
from them reported separately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since ath6kl does not actually update cfg80211 BSS table when this
event occurs, there is not much need for removing the entries from
the internal table that is not really used or exposed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl does not actually update cfg80211 BSS table when this update
occurs, so there is not much need in updating the internal table
that is not used or exposed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This event has been deprecated and there is no need for ath6kl to
include code for processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes the BSS "update" just before the connected or roamed event.
The previous implementation was completely broken: it forced a hardcoded
signal strength and IEs from Association _Request_ frame instead of any
Beacon information. This broke various things, including PMKSA caching.
The current workaround for creating a dummy BSS entry before the roamed
event is not exactly ideal, but that is quite a bit better than the
previous state. As a future improvement, cfg80211 could potentially be
extended to allow this type of use or ath6kl could delay sending the
roamed event before receiving a BSS info event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, the caldata continues to retain older history
values learned on that channel. It is always safer to start
noise floor calibration from the defaults after the assoication.
So this patch resets the nf history buffer when none of the
STA vifs are associated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR913x uses the same PLL register layout as AR9160 and later.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_set_diversity is only called from init.c where it cannot affect
the hardware setting because it's cleared on the next reset.
Instead of using a PHY op for something that's supposed to be initialized
statically, set the register value directly in the INI override function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eeprom .set_addac function is only necessary for AR9160, remove it
from eeprom_4k.c and remove the dummy function from eeprom_9287.c
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- AR_SREV_5416_20_OR_LATER is always true, remove it
- AR_SREV_9280_20_OR_LATER is always true within eeprom_4k.c and eeprom_9287.c
- (AR_SREV_9271 || AR_SREV_9285) is always true in eeprom_4k.c
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver inserts padding between the 802.11 header and data, it
needs to set the hdr variable to the new header location.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configuration of the WEP keys needs to be delayed until the AP mode has
been properly started at the target. Partial support for delaying the
WEP key configuration was already in place in the driver, but the actual
part of deciding when to do this was missing.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the new EDMA descriptor format, a single descriptor can contain up
to four buffer pointers. By splitting the buffer into two parts, we can
let the hardware add the padding internally instead of using memmove on
the skb data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only flag that needs to be set when ath_tx_rc_status is called with
rc_update == false is the IEEE80211_TX_STAT_TX_FILTERED flag. All other
data is ignored in that case.
This flag can be set from ath_tx_complete_buf instead, so that we can
drop a few redundant calls to ath_tx_rc_status and remove the rc_update
function parameter
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_lookup_legacy now checks all the tx rate flags for MCS vs legacy
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_hw_cycle_counters_update only needs to be called if the power state
changes. Most of the time this does not happen, even when ps_usecount
goes down to 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new API, tx descriptors can be written in one single pass
instead of having to re-read and rewrite fields from multiple places.
This makes the code easier to read and also slightly improves performance
on embedded MIPS hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using lots of different functions with long argument lists,
pull all the necessary information from one struct. This makes the code
easier to read and eliminates the need for copying data between multiple
linked descriptors.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of accesses to uncached descriptor memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that only ath9k_hw_set_desc_link needs to recalculate the tx
descriptor checksum on AR9380+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it easier to clean up the ath9k_hw descriptor API
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a reset, rx buffers are flushed after rx has been disabled. To avoid
race conditions, rx needs to stay disabled during the reset, so avoid any
calls to ath9k_hw_rxena in that case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting the AP beacon timer, it assumes that the TSF has recently
been cleared. Set the SC_OP_TSF_RESET flag to ensure that this is always
the case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler increases the interrupt disable refcount, so the
tasklet needs to always call ath9k_hw_enable_interrupts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ath_pci_resume it seems we are not enabling LED properly, in addition
we have a PS wrapper fix for this
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 seems to have issues sometimes with fast channel change
in 5GHz and this case is handled specifically for AR9280 by doing
a full reset. Let's do a full reset for 5GHz channles of AR9380
& for all channels of AR9280 pci chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the register macros to appropriate header files to be in
sync with other register definitions and also a single place
to refer everything.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx/rx gain table initval hanlding part so readability
is better and easy to manage the code.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initvals and register modifications required to support AR946/8x chipsets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a successful completion of disconnect() driver needs to set
it's sme_state to SME_DISCONNECTED to be in sync with cfg80211
state.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
