Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some devices (especially little-endian ones), the flash EEPROM data
has a different endian, which needs to be detected.
Add a flag to the platform data to allow overriding that behavior
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the initial NF calibration less likely to fail.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can cause inconsistent calibration results or in some cases turn the
radio deaf.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When NF calibration fails, the radio often becomes deaf. The usual
hardware hang checks do not detect this, so it's better to issue a reset
when that happens.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "goto chip_reset" is a bit misleading, because it does not actually
issue a chip reset. Instead it is bypassing processing of other
interrupts and assumes that the tasklet will issue a chip reset.
In the case of RXORN this does not happen, so bypassing processing of
other interrupts will simply allow them to fire again. Even if RXORN
was triggering a reset, it is not critical enough to need the bypass
here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
UB124 is a USB based reference design not supported by ath9k or
ath9k_htc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix a 11b/EVM issue by adjusting
FIR filter coefficients.
* Fix a problem with receiving probe request
frames sent at 11b rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently has a race which can be hit
with this sequence:
* Start a scan operation.
* TX BA is initiated by ieee80211_start_tx_ba_session().
* Driver sets up internal state and calls
ieee80211_start_tx_ba_cb_irqsafe().
* mac80211 adds a packet to sdata->skb_queue with
type IEEE80211_SDATA_QUEUE_AGG_START.
* ieee80211_iface_work() doesn't process the
packet because scan is in progress.
* ADDBA response timer expires and the sta/tid is
torn down.
* Driver receives BA stop notification and calls
ieee80211_stop_tx_ba_cb_irqsafe().
* This is also added to the queue by mac80211.
* Now, scan finishes.
At this point, the queued up packets might be processed
if some other operation schedules the sdata work. Since
the tids have been cleaned up already, warnings are hit.
If this doesn't happen, the packets are left in the queue
until the interface is torn down.
Since initiating a BA session when scan is in progress
leads to flaky connections, especially in MCC mode, we
can drop the TX BA request. This improves connectivity
with legacy clients in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flush timeout in MCC mode is very small, since
we are constrained by the time slice for each
channel context, but since only the HW queues are
flushed when switching contexts, it is acceptable.
Since the SW queues are also emptied in the mac80211 flush()
callback, a larger duration is needed. Add an override
argument to __ath9k_flush() and set it when flush()
is called in MCC mode. This allows the driver to
drain both the SW and HW queues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using ATH_CHANCTX_EVENT_ASSIGN to abort
a HW scan when a new interface becomes active, use the
mgd_prepare_tx() callback. This allows us to make
sure that the GO's channel becomes operational by
using flush_work().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that a GO interface
sends out a new NoA schedule with 200ms duration
when mgd_prepare_tx() is called.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 has to be notified when a RoC period
expires in the driver. In MCC mode, since the
offchannel/RoC timer is set with the requested
duration, ieee80211_remain_on_channel_expired() needs
to be called when the timer expires.
But, currently it is done after we move back to
the operating channel. This is incorrect - fix this
by calling ieee80211_remain_on_channel_expired() when
the RoC timer expires and in ath_roc_complete() when
the RoC request is aborted.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a GO interface is active when we receive a
mgd_prepare_tx() call, then we need to send
out a new NoA before switching to a new context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since both the arguments need to satisfy
the alignment requirements of ether_addr_copy(),
use memcpy() in cases where there will be no
big performance benefit and make sure that
ether_addr_copy() calls use properly aligned
arguments.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH_CHANCTX_EVENT_AUTHORIZED is required to trigger
the MCC scheduler when a station interface becomes
authorized. But, since the driver gets station state
notifications when the current operating mode is AP
too, make sure that we send ATH_CHANCTX_EVENT_AUTHORIZED
only when the interface is in station mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pending frames in the driver can be present
either in the HW queues or SW. ath9k_has_pending_frames()
currently checks for the HW queues first and then
checks if any ACs are queued in the driver.
In MCC mode, we need to check the HW queues alone, since
the SW queues are just marked as 'stopped' - they will
be processed in the next context switch. But since we
don't differentiate this now, mention whether we want
to check if there are frames in the SW queues.
* The flush() callback checks both HW and SW queues.
* The tx_frames_pending() callback does the same.
* The call to __ath9k_flush() in MCC mode checks HW queues alone.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An offchannel operation also needs to have
a flush timeout that doesn't exceed the NoA
absence duration of a GO context, so use
channel_switch_time. The first offchannel
operation is set a flush timeout of 10ms since
channel_switch_time will be zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, the duration for a channel context
is half the beacon interval and having a large
flush timeout will adversely affect GO operation,
since the default value of 200ms will overshoot
the advertised NoA absence duration.
The scheduler initiates a channel context switch
only when the slot duration for the current
context expires, so there is no possibility of
having a fixed timeout for flush.
Since the channel_switch_time is added to the
absence duration when the GO sets up the NoA
attribute, this is the maximum time that we
have to flush the TX queues. The duration is very
small, but we don't have a choice in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timeout value for flushing the TX queues
is hardcoded at 200ms right now. Use a channel
context-specific value instead to allow adjustments
to the timeout in case MCC is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an active context transitions to inactive
state, the NoA schedule needs to be removed
for the context that has beaconing enabled.
Not doing this will affect p2p clients.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a chip reset is done, all running timers,
tasklets etc. are stopped but the beacon tasklet
is left running. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a HW reset is done, the interrupt tasklet is
disabled before ISRs are disabled in the HW. This
allows a small window where the HW can still generate
interrupts. Since the tasklet is disabled and not killed,
it is not scheduled but deferred for execution at a later
time.
This happens because ATH_OP_HW_RESET is not set when ath_reset()
is called. When the hw_reset_work workqueue is used, this
problem doesn't arise because ATH_OP_HW_RESET is set
and the ISR bails out.
Set ATH_OP_HW_RESET properly in ath_reset() to avoid
this race - all the ath_reset_internal() callers have
been converted to use ath_reset() in the previous patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having ath_reset_internal() and ath_reset()
as two separate calls to perform a HW reset, have
one function. This makes sure that the behavior will
be the same at all callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the current operating channel context has
been marked as ATH_CHANCTX_STATE_FORCE_ACTIVE,
do not process beacons that might be received,
since we have to wait for the station to become
authorized.
Also, since the cached TSF value will be zero
initially do not rearm the timer in this
case when a beacon is received, since it results
in spurious values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, currently the decision to enable
the multi-channel state machine is done
based on the association status if one of
the interfaces assigned to a context is in
station mode.
This allows the driver to switch to the other
context before the current station is able to
complete the 4-way handshake in case it is
required and this causes problems.
Instead, enable multi-channel mode when the
station moves to the authorized state. This
disallows an early switch to the other channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the sta_add()/sta_remove() callbacks,
use the sta_state() callback since this gives
more fine-grained control.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rts threshold was being configured instead of
fragmentation threshold.
Keep in mind available firmware binaries don't
seem to support fragmentation anyway so this
doesn't fix fragmentation threshold per se.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When user space requests survey info, it is useful to know which of the survey
data refers to the channel that is currently actively being used. One of the
use cases is getting the current channel noise for status output. Without this
flag you would have to look up the channel separately and then compare it
against the frequency in the survey output in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of defining a completely new tracepoint
use an existing tracepoint class.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fundamentally this was wrong. Tsf is only valid
in last MPDU of a PPDU. This means tsf value was
wrong most of the time during heavy traffic.
Also I don't see much point in exposing a
redundant (and broken) tsf value. Userspace can
already read it from the dumped rx descriptor
buffer.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once driver entered the rx_confused state it would
refuse to rx even after firmware is restarted.
Make sure to clear it so that rx works after, e.g.
hw restart or after all interfaces are stopped.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In theory it was possible to drain entire HTT Rx
ring via fragmented Rx leading to Rx lockup.
In practice non-data traffic would always trigger
replenishment via the regular Rx handler.
For correctness sake make sure to replenish the
ring on fragmented Rx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The netbuf pop can return NULL. Make sure to check
for that. It shouldn't happen but better safe than
sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's little point in dropping, e.g. frames with
FCS error early in ath10k.
This simplifies amsdu_allowed() and gets rid of
htt_rx_mpdu_status usage finally.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Treat non-chained and chained popping the same
way. Also this makes netbuf pop fully symmetrical
to (re)filling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the globally defined ieee80211 values instead
of re-defining them in the driver again.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL was pretty greedy
and because of that ath10k ended up dropping
Control Frames as well as Null Func frames.
Reported-by: Okhwan Lee <ohlee@mwnl.snu.ac.kr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
