Include new enum to define wmi service bitmap definitions for
10.4 firmware and a function wmi_10_4_svc_map() to remap 10.4
firmware wmi service bitmap definitions to ath10k generic wmi
services.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca99X0 chip uses firmware version 10.4. Define a new macro
ATH10K_FW_WMI_OP_VERSION_10_4 for 10.4 firmware and include
in switch cases where ATH10K_FW_WMI_OP_VERSION_* is used
to avoid compilation error.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
BMI parameter value to execute downloaded otp binary
is different for QCA99X0. Have a member in hw_params
to hold hw specific BMI param.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is more than 1 sec delay in getting response from target
through BMI in QCA99X0. Increase the BMI communication timeout
to 2*HZ to fix BMI failures.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:
echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value
BUG: unable to handle kernel paging request at ffffc90001e080e0
IP: [<ffffffff8135c860>] ioread32+0x40/0x50
...
Call Trace:
[<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
[<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
[<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
[<ffffffff81189758>] __vfs_read+0x28/0xe0
[<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
[<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
[<ffffffff81189e1a>] vfs_read+0x8a/0x140
[<ffffffff8118acb9>] SyS_read+0x49/0xb0
[<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
[<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable VHT support for IBSS, while mac80211/cfg80211 and
wpa_supplicant already support this.
In my test env, qca988x 2x2 I get:
(udp) ath10k-1 >>>> ath10k-2 (server) - speed: 419 Mbits/sec
(tcp) ath10k-1 >>>> ath10k-2 (server) - speed: 404 Mbits/sec
During tests I used wpa_supplicant (latest git version), which
already support IBSS VHT, and choose highest available BW. Also tested with
qca6174.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version itself isn't sufficient to know what
HTT version given firmware blob uses. Hence print
the recently introduced HTT op version code.
While at it make the info string a bit more
consistent and clear.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the support of channel switching functionality, similar
to ath9k support.
Tested with TP-Link TL-WN722N and TL-WN821N.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Need to reorder init sequence to run wil_platform_init
before pci_enable_device. Assumption is platform init
may be required before device may be enabled.
Another issue, platform uninit should be called after
pci_disable_device because platform uninit may render
pci device non-accessible.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide platform hooks for module init/exit.
If platform require to perform some specific actions
in global context, this is where to do so.
Example may be turning on power for the PCIE based
on DT information.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass hidden SSID information to FW for proper operation.
In order to be able to scan/connect to the hidden SSID, SSID
setting is added when scan is requested from FW. SSID
scanning currently supports single SSID due to FW limitation.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide detailed statistics for the Rx frames per MCS
Statistics printed in "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware defines new memory region, mac_rgf_ext
that need to be accessed from the host for debug purposes.
Add corresponded mapping
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Control Bcast ring size in similar way as Rx and Tx ones,
through "bcast_ring_order" modparam, actual ring size is 1 << order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When one client is associated and connected to an ar6003 hw version
2.0 with firmware 3.1.1.149, and another client tries to connect, the
first client's MAC address is lost in the station list because the
"aid" is always "1". The structure "wmi_connect_event" has the "aid"
as the second byte in the message, but it should be the first byte.
This patch has been tested with linux-3.10.40
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found during code review. This was pretty much
impossible to happen but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the midst of chanctx patch review channel
switching became broken which I failed to notice
until now.
Function ath10k_mac_vif_chan() reports current
chandef which isn't updated until after
switch_vif_chanctx() is returned from.
Consequently the driver just restarted operation
on channels it was residing already instead of
switching to the new ones.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In practice there's no point in having a copy of
chanctx_conf.
Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().
The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Channel contexts aren't iterable until after
they've been added to the driver. The code assumed
otherwise.
This problem could result in:
* rx_channel being NULL and forcing Rx path to go
the slow way to get channel on QCA988X,
* report incorrect channel when running
multi-channel on QCA61X4 hw2.1,
* report incorrect channel after AP channel
switch.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.
Fixes: d84a512dca ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When wmi mgmt event function fails to parse given skb,
it should be freed on failure condition to avoid memory
leaks. Found this during the code review.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.
As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.
There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
