88pm800 has two addtional pages - power and gpadc.
The address of the pages depends on the address of 88pm800.
So do not need pass the address of the power and gpadc in
platform data.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88pm800/88pm805 interrupt is asserted low if the events happened.
So remove IRQF_TRIGGER_FALLING for irq request.
Also, the interrupt wiring is board dependent so do not set
IRQF_TRIGGER by default.
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Move "device_800_init" to fix NULL pointer error when
calling "device_gpadc_init" as it needs "subchip->regmap_gpadc"
to set registers via regmap interface
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch integrates the wm8997 into the Arizona mfd.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that the device is in a known good state. This should have little
practical impact as the runtime PM will reset the device shortly after
probe but it's neater.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A complete refurbished series inclunding:
- DT support for the MFD, TSC and ADC driver & platform device support,
which has no users, has been killed.
- iio_map from last series is gone and replaced by proper nodes in the
device tree.
- suspend fixes which means correct data structs are taken and no
interrupt storm
- fifo split which should problem with TSC & ADC beeing used at the same
time
- The ADC channels are now checked before blindly applied. That means the
touch part reads X, Y and Z coordinates and does not mix them up. Same
goes for the IIO ADC driver.
- The IIO ADC driver now creates files named in_voltageX_raw where X
represents the ADC line instead of a number starting at 0. A read from
this file can return -EBUSY in case touch is busy and the ADC didn't
collect a value.
Saves on code and simplifies the driver, as these resources are now
tracked and freed automatically when the driver is realised.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB8500 external regulator driver is now a device in its own right,
so it requires registering and probing in the normal way. This patch
will ensure the driver is probed once registered for all devices which
support them.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add of_compatible string to the ab8500-codec cell to allow the driver to
grab handlers such as regulators from device-tree when available.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ab8500-leds driver has never been upstreamed and was replaced by a
PWM framework based driver, so these references are not needed anymore.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: arizona: Updates for v3.10
A bunch of enhancements and fixes for the arizona devices, adding a few
new features (the main one being device tree) and improving robustness.
The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
TI-adc reads a little better compared to tiadc. And if we add am335x to
it then we have the same naming scheme as the tsc side.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch removes access to platform data mfd_tscadc_board because the
platform is DT only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Add DT support in the MFD core driver. The node name is "am3359" because
it was tested on this platform.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch adds DT support to touch driver. It also provides a binding
document which is used by the MFD and IIO part of the device.
This patch also renames steps_to_configure to coordinate_readouts
because the original name misleads the purpose of the variable.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch adds support for SYSCON driver for CLPS711X targets.
At this time there are no users for this driver, but it is will
be used as start point to use in CLPS711X drivers and remove
<mach/xx> dependencies.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
In preparation to switching the jz4740 clk driver to the common clk framework
update the clk enable/disable calls to clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX77686 clock driver has been in-tree for over 6 months, but never
actually enabled through the MFD registration before.
Add it to the table so the device will probe and configure properly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interrupt controller on the wm8994 series of devices requires a level
triggered parent. If one is not available but a GPIO is available for the
interrupt then emulate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
