Do the overlay frontbuffer tracking properly so that it matches
the state of the overlay on/off/continue requests.
One slight problem is that intel_frontbuffer_flip_complete()
may get delayed by an arbitrarily liong time due to the fact that
the overlay code likes to bail out when a signal occurs. So the
flip may not get completed until the ioctl is restarted. But fixing
that would require bigger surgery, so I decided to ignore it for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481131693-27993-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
First set of i915 fixes for code in next.
* tag 'drm-intel-next-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: skip the first 4k of stolen memory on everything >= gen8
drm/i915: Fallback to single PAGE_SIZE segments for DMA remapping
drm/i915: Fix use after free in logical_render_ring_init
drm/i915: disable PSR by default on HSW/BDW
drm/i915: Fix setting of boost freq tunable
drm/i915: tune down the fast link training vs boot fail
drm/i915: Reorder phys backing storage release
drm/i915/gen9: Fix PCODE polling during SAGV disabling
drm/i915/gen9: Fix PCODE polling during CDCLK change notification
drm/i915/dsi: Fix chv_exec_gpio disabling the GPIOs it is setting
drm/i915/dsi: Fix swapping of MIPI_SEQ_DEASSERT_RESET / MIPI_SEQ_ASSERT_RESET
drm/i915/dsi: Do not clear DPOUNIT_CLOCK_GATE_DISABLE from vlv_init_display_clock_gating
drm/i915: drop the struct_mutex when wedged or trying to reset
Here's the one lonely bugfix I talked about on irc.
* tag 'drm-misc-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-misc:
drivers/gpu/drm/ast: Fix infinite loop if read fails
- fix display regression on DCE6/8
- Powergating fixes for GFX8
- amdgpu SI fixes (golden settings, proper rev id setup, etc.)
* 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: update tile table for oland/hainan
drm/amdgpu: update tile table for verde
drm/amdgpu: update rev id for verde
drm/amdgpu: update golden setting for verde
drm/amdgpu: update rev id for oland
drm/amdgpu: update golden setting for oland
drm/amdgpu: update rev id for hainan
drm/amdgpu: update golden setting for hainan
drm/amdgpu: update rev id for pitcairn
drm/amdgpu: update golden setting for pitcairn
drm/amdgpu: update golden setting/tiling table of tahiti
drm/amdgpu: fix cursor setting of dce6/dce8
drm/amdgpu: refine set clock gating for tonga/polaris
drm/amdgpu: initialize cg flags for tonga/polaris10/polaris11.
drm/amdgpu: add new gfx cg flags.
drm/amdgpu: fix pg can't be disabled by PG mask.
drm/amdgpu: always initialize gfx pg for gfx_v8.0.
drm/amdgpu: enable AMD_PG_SUPPORT_CP in Carrizo/Stoney.
drm/amdgpu: fix init save/restore list in gfx_v8.0
drm/amdgpu: fix enable_cp_power_gating in gfx_v8.0.
...
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
Apparently some VLV BIOSen like to leave the VDD force bit enabled
even for power seqeuncers that aren't properly hooked up to any
port. That will result in a imbalance in the AUX power domain
refcount when we stat to use said power sequencer as edp_panel_vdd_on()
will not grab the power domain reference if it sees that the VDD is
already on.
To fix this let's make sure we turn off the VDD force bit when we
initialize the power sequencer registers. That is, unless it's
being done from the init path since there we are actually
initializing the registers for the current power sequencer and
we don't want to turn VDD off needlessly as that would require
waiting for the power cycle delay before we turn it back on.
This fixes the following kind of warnings:
WARNING: CPU: 0 PID: 123 at ../drivers/gpu/drm/i915/intel_runtime_pm.c:1455 intel_display_power_put+0x13a/0x170 [i915]()
WARN_ON(!power_domains->domain_use_count[domain])
...
v2: Fix typos in comment (David)
Cc: stable@vger.kernel.org
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98695
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161220165117.24801-1-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
This patch removes the users of the deprectated APIs:
acpi_get_table_with_size()
early_acpi_os_unmap_memory()
The following APIs should be used instead of:
acpi_get_table()
acpi_put_table()
The deprecated APIs are invented to be a replacement of acpi_get_table()
during the early stage so that the early mapped pointer will not be stored
in ACPICA core and thus the late stage acpi_get_table() won't return a
wrong pointer. The mapping size is returned just because it is required by
early_acpi_os_unmap_memory() to unmap the pointer during early stage.
But as the mapping size equals to the acpi_table_header.length
(see acpi_tb_init_table_descriptor() and acpi_tb_validate_table()), when
such a convenient result is returned, driver code will start to use it
instead of accessing acpi_table_header to obtain the length.
Thus this patch cleans up the drivers by replacing returned table size with
acpi_table_header.length, and should be a no-op.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 848496e590
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Jul 13 16:32:03 2016 +0300
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.
I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.
To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.
v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c171 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8afcf ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com
(cherry picked from commit a0b8a1fe34)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Looking at the ADF code from the Android kernel sources for a
cherrytrail tablet I noticed that it is calling the
MIPI_SEQ_ASSERT_RESET sequence from the panel prepare hook.
Until commit b1cb1bd291 ("drm/i915/dsi: update reset and power sequences
in panel prepare/unprepare hooks") the mainline i915 code was doing the
same. That commits effectively swaps the calling of MIPI_SEQ_ASSERT_RESET /
MIPI_SEQ_DEASSERT_RESET.
Looking at the naming of the sequences that is the right thing to do,
but the problem is, that the old mainline code and the ADF code was
actually calling the right sequence (tested on a cube iwork8 air tablet),
and the swapping of the calling breaks things.
This breakage was likely not noticed in testing because on cherrytrail,
currently chv_exec_gpio ends up disabling the gpio pins rather then
setting them (this is fixed in the next patch in this patch-set).
This commit fixes the swapping by fixing MIPI_SEQ_ASSERT/DEASSERT_RESET's
places in the enum defining them, so that their (new) names match their
actual use.
Changes in v2:
-Add a comment to the enum explaining that the assert/reassert names
are swapped in the spec
Fixes: b1cb1bd291 ("drm/i915/dsi: update reset and power sequences...")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202150128.29871-1-hdegoede@redhat.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 2b8208ac93)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On my Cherrytrail CUBE iwork8 Air tablet PIPE-A would get stuck on loading
i915 at boot 1 out of every 3 boots, resulting in a non functional LCD.
Once the i915 driver has successfully loaded, the panel can be disabled /
enabled without hitting this issue.
The getting stuck is caused by vlv_init_display_clock_gating() clearing
the DPOUNIT_CLOCK_GATE_DISABLE bit in DSPCLK_GATE_D when called from
chv_pipe_power_well_ops.enable() on driver load, while a pipe is enabled
driving the DSI LCD by the BIOS.
Clearing this bit while DSI is in use is a known issue and
intel_dsi_pre_enable() / intel_dsi_post_disable() already set / clear it
as appropriate.
This commit modifies vlv_init_display_clock_gating() to leave the
DPOUNIT_CLOCK_GATE_DISABLE bit alone fixing the pipe getting stuck.
Changes in v2:
-Replace PIPE-A with "a pipe" or "the pipe" in the commit msg and
comment
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97330
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202142904.25613-1-hdegoede@redhat.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 721d484563)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Don't even tell the mm allocator to handle the first page of stolen on
the affected platforms. This means that we won't inherit the FB in
case the BIOS decides to put it at the start of stolen. But the BIOS
should not be putting it at the start of stolen since it's going to
get corrupted. I suppose the bug here is that some pixels at the very
top of the screen will be corrupted, so it's not exactly easy to
notice.
We have confirmation that the first page of stolen does actually get
corrupted, so I really think we should do this in order to avoid any
possible future headaches, even if that means losing BIOS framebuffer
inheritance. Let's not use the HW in a way it's not supposed to be
used.
Notice that now ggtt->stolen_usable_size won't reflect the ending
address of the stolen usable range anymore, so we have to fix the
places that rely on this. To simplify, we'll just use U64_MAX.
v2: don't even put the first page on the mm (Chris)
v3: drm_mm_init() takes size instead of end as argument (Ville)
v4: add a comment explaining the reserved ranges (Chris)
use 0 for start and U64_MAX for end when possible (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94605
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1481808235-27607-1-git-send-email-paulo.r.zanoni@intel.com
