Powerplay uses cgs to load the firmware so add a function
to release it as well to avoid leaking it on driver unload.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since vmid-mgr supports vmid sharing in one vm, the same ctx could
get different vmids for two emits without vm flush, vm_flush could
be done in another ring.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
should fist halt engine, and then doing the register
programing, and later unhalt engine, and finally run
ring_test.
this help fix reloading driver hang issue of SDMA
ring
original sequence is wrong for it programing engine
after unhalt, which will lead to fault behavior when
doing driver reloading after unloaded.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1,should use late_fini to kfree all resource otherwise
the released pointer maybe accessed in IRQ ip fini routine.
2,hwmgr should not be kfree by pem_fini which is invoked
by hw fini path.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The PM core introduced the ability to keep devices runtime suspended
during the entire system suspend/resume process with commit aae4518b31
("PM / sleep: Mechanism to avoid resuming runtime-suspended devices
unnecessarily"). Before this so-called "direct-complete" procedure was
introduced, devices were always runtime resumed only to be immediately
put to sleep again using their ->suspend hook. Direct-complete is
enabled by returning a positive value from the ->prepare hook. The PCI
core usually does this automatically.
Direct-complete is only available for a device if all children use it as
well. Currently we cannot support direct-complete for DRM drivers
because the DRM core automatically registers multiple DRM minors which
belong to device class drm_class, and drm_class uses a struct dev_pm_ops
which lacks the ->prepare callback.
While this could be solved by adding the missing ->prepare callback,
closer inspection shows that there are no DRM drivers left which declare
the legacy ->suspend and ->resume callbacks in their drm_driver struct.
The last ones to remove them were i915 with commit 1751fcf9f9
("drm/i915: Fix module initialisation, v2.") and exynos with commit
e7fefb1d5a ("drm/exynos: remove legacy ->suspend()/resume()").
Consequently the struct dev_pm_ops of drm_class is now dead code. Remove
it. If no dev_pm_ops is declared for a device, the PM core automatically
enables direct-complete for it, thereby making that mechanism available
to the parent DRM PCI devices.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/da848fcd5ca72a35d9a722e644719977a47bb7ba.1465382836.git.lukas@wunner.de
This pull request brings in vblank/pageflip fixes I had hoped to see
merged before 4.7rc1, plus two new fixes that have come in since then.
* tag 'drm-vc4-fixes-2016-06-06' of github.com:anholt/linux:
drm/vc4: Make pageflip completion handling more robust.
drm/vc4: Fix ioctl permissions for render nodes.
drm/vc4: Return -EBUSY if there's already a pending flip event.
drm/vc4: Fix drm_vblank_put/get imbalance in page flip path.
drm/vc4: Fix get_vblank_counter with proper no-op for Linux 4.4+
Fixes for two issues reported by KASAN, a display engine hang due to
incorrect BIOS table parsing, and incorrect LTC interrupt handling on
Maxwell which could lead to a never-ending interrupt storm.
* 'linux-4.7' of git://github.com/skeggsb/linux:
drm/nouveau/disp/sor/gm107: training pattern registers are like gm200
drm/nouveau/disp/sor/gf119: both links use the same training register
drm/nouveau/core: swap the order of imem/fb
drm/nouveau/fbcon: fix out-of-bounds memory accesses
drm/nouveau/gr/gf100-: update sm error decoding from gk20a nvgpu headers
drm/nouveau/ltc/gm107-: fix typo in the address of NV_PLTCG_LTC0_LTS0_INTR
drm/nouveau/bios/disp: fix handling of "match any protocol" entries
omapdrm changes for 4.8
* Update MAINTAINERS file for omapdrm and tilcdc
* PLL refactoring to allow versatile use of the PLL clocks
* Public omapdss header refactoring to separate omapfb and omapdrm
* Gamma table support
* Support reset GPIO and vcc regulator in omapdrm's panel-dpi
* Minor cleanups
* tag 'omapdrm-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (69 commits)
drm/omapdrm: Implement gamma_lut atomic crtc properties
drm/omapdrm: Workaround for errata i734 (LCD1 Gamma) in DSS dispc
drm/omapdrm: Add gamma table support to DSS dispc
drm: drm_helper_crtc_enable_color_mgmt() => drm_crtc_enable_color_mgmt()
drm/omap: rename panel/encoder Kconfig names
drm: omapdrm: add DSI mapping
drm: omapdrm: Remove unused omap_framebuffer_bo function
drm: omapdrm: Remove unused omap_gem_tiled_size function
drm: omapdrm: panel-lgphilips-lb035q02: Remove unused backlight GPIO
drm/omap: panel-dpi: implement support for a vcc regulator
drm/omap: panel-dpi: make (limited) use of a reset gpio
devicetree/bindings: add reset-gpios and vcc-supply for panel-dpi
MAINTAINERS: Add maintainer for TI LCDC DRM driver
MAINTAINERS: Add maintainer for OMAP DRM driver
drm/omap: fix pitch round-up
drm/omap: remove align_pitch()
drm/omap: remove unnecessary pitch round-up
drm/omap: remove unneeded gpio includes
drm/omap: Remove the video/omapdss.h and move it's content to local header file
[media] omap_vout: Switch to use the video/omapfb_dss.h header file
...
Virtio-gpu updates
* 'virtio-gpu-for-airlied' of git://git.kraxel.org/linux:
virtio-gpu: use src not crtc
virtio-gpu: pick up hotspot from framebuffer
add cursor hotspot to drm_framebuffer
virtio-gpu: switch to atomic cursor interfaces
virtio-gpu: add atomic_commit function
virtio-gpu: fix output lookup
- some polish for the guc code (Dave Gordon)
- big refactoring of gen9 display clock handling code (Ville)
- refactoring work in the context code (Chris Wilson)
- give encoder/crtc/planes useful names for debug output (Ville)
- improvements to skl/kbl wm computation code (Mahesh Kumar)
- bunch of smaller improvements all over as usual
* tag 'drm-intel-next-2016-06-06' of git://anongit.freedesktop.org/drm-intel: (64 commits)
drm/i915: Update DRIVER_DATE to 20160606
drm/i915: Extract physical display dimensions from VBT
drm/i915: Silence "unexpected child device config size" for VBT on 845g
drm/i915/skl+: Use scaling amount for plane data rate calculation (v4)
drm/i915/skl+: calculate plane pixel rate (v4)
drm/i915/skl+: calculate ddb minimum allocation (v6)
drm/i915: Don't try to calculate relative data rates during hw readout
drm/i915: Only ignore eDP ports that are connected
drm/i915: Update GEN6_PMINTRMSK setup with GuC enabled
drm/i915: kill STANDARD/CURSOR plane screams
drm/i915: Give encoders useful names
drm/i915: Give meaningful names to all the planes
drm/i915: Don't leak primary/cursor planes on crtc init failure
drm/i915: Set crtc->name to "pipe A", "pipe B", etc.
drm/i915: Use plane->name in debug prints
drm/i915: Use crtc->name in debug messages
drm/i915: Reject modeset if the dotclock is too high
drm/i915: Fix NULL pointer deference when out of PLLs in IVB
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/bxt: Sanitize CDCLK to fix breakage during S4 resume
...
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
lockless gem bo freeing patches (and the oddball related patch) for all
the drivers who's maintainers are asleep at the helm - includes you ;-)
I based this on top of drm-fixes to include Chris' fix for the cma issue.
* tag 'topic/lockless-gem-bo-freeing-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/arcpgu: Use lockless gem BO free callback
drm/sun4i: Use lockless gem BO free callback
drm/omapdrm: Nuke dummy fb->dirty callback
drm/msm: Nuke dummy fb->dirty callback
drm/rockchip: Use cma gem vm ops
drm/sti: Use lockless gem BO free callback
drm: sti: remove useless call to dev->struct_mutex
drm/virtio: Use lockless gem BO free callback
drm/tilcdc: Use lockless gem BO free callback
drm/shmob: Use lockless gem BO free callback
drm/rockchip: Use lockless gem BO free callback
drm/rcar-du: Use lockless gem BO free callback
drm/qxl: Use lockless gem BO free callback
drm/nouveau: Use lockless gem BO free callback
drm/mga200g: Use lockless gem BO free callback
drm/fls-dcu: Use lockless gem BO free callback
drm/cirrus: Use lockless gem BO free callback
drm/bochs: Use lockless gem BO free callback
drm/atmel: Use lockless gem BO free callback
drm/ast: Use lockless gem BO free callback
...
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the FSL DCU driver uses MMIO, the regmap bus of type
regmap_mmio is being used which has fast_io set to true.
Use flat regmap cache and specify max register to be large
enouth to cover all registers available in LS1021a and Vybrids
register space.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
objtool reports the following warnings:
drivers/gpu/drm/vmwgfx/vmwgfx_msg.o: warning: objtool: vmw_send_msg()+0x107: duplicate frame pointer save
drivers/gpu/drm/vmwgfx/vmwgfx_msg.o: warning: objtool: vmw_host_get_guestinfo()+0x252: duplicate frame pointer save
To quote Linus:
"The reason is that VMW_PORT_HB_OUT() uses a magic instruction sequence
(a "rep outsb") to communicate with the hypervisor (it's a virtual GPU
driver for vmware), and %rbp is part of the communication. So the
inline asm does a save-and-restore of the frame pointer around the
instruction sequence.
I actually find the objtool warning to be quite reasonable, so it's
not exactly a false positive, since in this case it actually does
point out that the frame pointer won't be reliable over that
instruction sequence.
But in this particular case it just ends up being the wrong thing -
the code is what it is, and %rbp just can't have the frame information
due to annoying magic calling conventions."
Silence the warnings by telling objtool to ignore the two functions
which use the VMW_PORT_HB_{IN,OUT} macros.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: DRI <dri-devel@lists.freedesktop.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160526184343.fdtjjjg67smmeekt@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
