BDW display - DP buffer translation values changed to give better margin.
Further change to entry 6; set dword 0 bit 31=1.
Both changes were approved already but this one didn't landed BSpec yet
this is why it is in a separated patch. Making reviewer's life easier.
Also alowing separated tests and any future bisect that might be needed.
Reference: Predator r74080 / HSD 4394389
v2: Arthur noticed I was changing the wrong bit.
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's make sure PSR is propperly disabled before to re-enabled it.
According to Spec, after disabled PSR CTL, the Idle state might occur
up to 24ms, that is one full frame time (1/refresh rate),
plus SRD exit training time (max of 6ms),
plus SRD aux channel handshake (max of 1.5ms).
So if something went wrong PSR will be disabled until next full
enable/disable setup.
v2: The 24ms above takes in account 16ms for refresh rate on 60Hz mode. However
on low frequency modes this can take longer. So let's use 50ms for safeness.
v3: Move wait out of psr.lock critical area.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sw cache clean on BDW is a tempoorary workaround because we cannot
set cache clean on blt ring with risk of hungs. So we are doing the cache clean on sw.
However we are doing much more than needed. Not only when using blt ring.
So, with this extra w/a we minimize the ammount of cache cleans and call it only
on same cases that it was being called on gen7.
The traditional FBC Cache clean happens over LRI on BLT ring when there is a
frontbuffer touch happening. frontbuffer tracking set fbc_dirty variable
to let BLT flush that it must clean FBC cache.
fbc.need_sw_cache_clean works in the opposite information direction
of ring->fbc_dirty telling software on frontbuffer tracking to perform
the cache clean on sw side.
v2: Clean it a little bit and fully check for Broadwell instead of gen8.
v3: Rebase after frontbuffer organization.
v4: Wiggle confused me. So fixing v3!
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel has to be reconfigured only when it really loose the power.
The traditional enable/disable sequence already take care of this so we can
minimize the time spend on every re-enable.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen9 is different enough (for instance, fetching the memory latency
values is different from ILK+) to not take the HAS_PCH_SPLIT() branch,
so let's prefer a clean separation.
v2: Rebase on top of the broadwell_init_clock_gating() name change
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It can be handy to get the number of planes for this pipe, ie including
the primary plane to loop over them. Introduce a little function to do
so.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can be useful to declare structures around pipes and planes and
don't have to go back auditing the code if the next platorm bump that
number.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL Uses the same hardware for all planes now, so called "universal"
planes. Ie both the primary planes and sprite planes share the same
logic. This patch implements the drm_plane vfuncs for "sprites" ie
planes that aren't the primary plane.
v2: Couple of fixes:
- Actually enabled the planes and fix the plane number
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Skylake, we use plane1 as primary plane and plane2/3 as sprite
planes.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To accomodate the extra planes, the bit definitions were shuffled around
a bit.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v3: Rebase after yet another change int that area (done with wiggle)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set gen 9 function pointers for eld write and global resource.
Implementation remains same as HSW.
v2: Rebase on top of Sonika's untangling of the if/else ladder (Damien)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake doesn't use the pre-charge field now, but, instead, we need to
specify the total number of SYNC pulses for the SYNC phase (pre-charge +
SYNC pattern pules). Let's use the default value (32) for that.
v3: increase DP AUX TX timeout as 400us is not to be used on SKL
apparently (Jesse).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to provide a vfunc that will make the code in intel_dp_aux_ch()
loop once to start the AUX transaction. The return value (clock divider)
is unused on SKL, so just return 1.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake introduces new stolen memory sizes starting at 0xf0 (4MB) and
growing by 4MB increments from there.
v2: Rebase on top of the early-quirk changes from Ville.
v3: Rebase on top of the PCI_IDS/IDS macro rename
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They are similar to Haswell.
v2: Rebased on top of drm-intel-nightly
v3: Rebased on top of Sonika's DP train defines renaming
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of things have changed compared to Broadwell:
- Entry 9 is used for eDP
- No more FDI
v2: Update the translation values to latest specs.
v3: Rebase on top of the BDW HDMI translation patch
v4: Remove the low voltage edp tables,
Rebase on top of the patch not writing the HDMI entry on eDP/FDI
DDIs (Satheesh, Paulo).
v5: Apply the / 2 fix for the number of HDMI entries (Satheesh)
v6: Rebase on top of Jani's clean up for the DDI_BUF_TRANS tables
v7: Restore the commit message that was mangled by error
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the platform doesn't have a FDI link, don't try to read out the
state of a potential PCH transcoder.
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Don't open-code HAS_FDI if there's only one place that needs
it. Acked by Damien on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of the intel_crt_present() addition
v3: Fix rebase error (we were patching the wrong function)
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake makes primary planes the same as sprite planes and call the
result "universal planes".
This commit emulates a primary plane with plane 0, taking the
opportunity to redefine primary and sprite registers to be identical now
that the underlying hardware is. It also makes sense as plenty of fields
have changed.
v2: Rebase on top of the vma code.
v3: Follow upstream evolution:
- Drop return values.
- Remove pipe checks since redudant and BUG instead.
- Remove tiling checks and BUG instead.
- Drop commented out DISP_MODIFY usage.
v4: s/plane/primary_plane/
v5: Misc fixes:
- Fix the fields we need to clear up
- Disable trickle feed
- Correctly use PLANE_OFFSET for the panning
v6: (Jesse)
Use pipe src size when programming plane size. This makes cloned configs
work correctly w/o the use of a panel fitter.
v7: Rebase on top of Ville's rmw elimination series
v8: Remove clearing the trickle feed bit now that we don't do a RMW (Rodrigo,
Damien)
Add a comment about the stride unit (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1,5,6,7)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2,3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following sets the AsyncFlip performance mode for everything above
Gen6:
commit 4790cb36b3eede8fb0cca529dc1d31b9936fa24b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:11:20 2013 +0000
drm/i915: Disable AsyncFlip performance optimisations
Starting from Gen9 the MI_MODE register layout changes and doesn't
include the above bit.
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in 2nd patch from Damien for more ids (Daniel)
v3: info->has*ring -> info->ring_mask conversion. Also add VEBOX support.
v4: Fold in update from Damien
v5: Rebase and add GEN_DEFAULT_PIPEOFFSETS
v6: Add more PCI ID (Vandana)
v7: Rebase and add IVB_CURSOR_OFFSETS
v8: Renamed the macro from _PCI_IDS to _IDS for consistency
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
