All functions and data types used by OF-specific code paths are declared
in <linux/of.h> regardless of CONFIG_OF. Replace the #ifdef CONFIG_OF
guard with a if(IS_ENABLED(CONFIG_OF)) and let the compiler optimize
the unused code away.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Testing on r8a7790 shows that INDT does not indicate the correct
pin state when reading a GPIO configured as output, so update
the gpio_rcar_get() function to handle this case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bug fix 352a2d5bf "gpio/omap: ensure gpio context is initialised"
has caused a new warning for omap1_defconfig:
drivers/gpio/gpio-omap.c:1465:13: warning: 'omap_gpio_init_context' defined but not used [-Wunused-function]
static void omap_gpio_init_context(struct gpio_bank *p) {}
^
The solution is to mark the stub function as 'static inline' so
it gets left out of the build when unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 7bce696 (gpio: Make gpio-msm-v1 into a platform driver,
2013-03-04) was based on an older kernel where __devinit still
existed. Remove the erroneous __devinit marking.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The free-function mentioned "interrupt" instead of "GPIO". While we are
here, use "GPIO" (capital letters) consistently.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver can be used on Xilinx ARM Zynq platform
where in_be32/out_be32 functions are not implemented.
Use __raw_readl/__raw_writel functions which are
implemented on Microblaze and PowerPC.
For ARM readl/writel functions are used instead.
The correct way how to implement this is to detect
endians directly on IP. But for the gpio case
without interrupt connected(it means without
interrupt logic) there are just 2 registers
data and tristate where auto detection can't be done.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Supporting the second channel in the driver.
Offset is 0x8 and both channnels share the same
IRQ.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplification is done by using OF helper function
which increase readability of code and remove
(if (var) var = be32_to_cpup;) assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From David Brown:
Cleanups for MSM for 3.11
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
* tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
mfd: ssbi: Use devm_* and simplify code
gpio: msm: Add device tree and irqdomain support for gpio-msm-v2
ARM: msm: Remove gpiomux-v2 and re-organize MSM_GPIOMUX configs
msm: iomap: Remove unused bases and mappings
msm: Remove unused file core.h
ARM: msm: Remove init_irq declaration in machine description
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/msm8660-surf.dts
arch/arm/boot/dts/msm8960-cdp.dts
From David Brown:
Some minor fixes for MSM for 3.11
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
* tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
gpio: msm-v1: Remove errant __devinit to fix compile
mfd: ssbi: Add MODULE_DEVICE_TABLE
ARM: dts: msm: Fix bad register addresses
arch: arm: mach-msm: using strlcpy instead of strncpy
Signed-off-by: Olof Johansson <olof@lixom.net>
From David Brown:
Some minor fixes for MSM for 3.11
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
* tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
gpio: msm-v1: Remove errant __devinit to fix compile
mfd: ssbi: Add MODULE_DEVICE_TABLE
ARM: dts: msm: Fix bad register addresses
arch: arm: mach-msm: using strlcpy instead of strncpy
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Renesas ARM based SoC GPIO R-Car updates for v3.11
DT support to GPIO R-Car driver by Laurent Pinchart.
* tag 'renesas-gpio-rcar-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (131 commits)
gpio-rcar: Add DT support
This cleans up the gpio-msm-v2 driver of all the global define usage.
The number of gpios are now defined in the device tree. This enables
adding irqdomain support as well.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Commit 7bce696 (gpio: Make gpio-msm-v1 into a platform driver,
2013-03-04) was based on an older kernel where __devinit still
existed. Remove the erroneous __devinit marking.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Remove gpiomux-v2 as it's not being used and make way for future improvements.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
There is no users of this code and there is already a pinctrl
driver written for s3c24xx which is going to be used on any
s3c24xx DT platforms. Hence this has been effectively a dead
code in mainline.
This reverts commit 172c6a1365
gpio: samsung: add devicetree init for s3c24xx arches
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Simon Horman:
Renesas ARM based SoC pinmux and GPIO update for v3.11
SH-PFC:
* Entries for INTC external IRQs
* Remove dependency on GPIOLIB
* PFC support for r8a7790 SoC
* Pinmux support for r8a7778 SoC
* Increase pin group and function coverage for sh7372, r8a7740,
r8a7778, r8a7779 and r8a7790 SoCs
* Use pinctrl mapping on mackerel, ap4evb, armadillo800eva,
bonito, bockw, lager boards
* Use RCAR_GP_PIN macro in marzen board
* Remove unused GPIOs for sh7372, sh73a0, r8a7740 and r8a7790 SoCs
* Add bias (pull-up/down) pinconf support for r8a7740 SoC
* Add VCCQ support for sh73a0
GPIO car:
* Add RCAR_GP_PIN macro
* Add support for IRQ_TYPE_EDGE_BOTH
* Make the platform data gpio_base field signed
The GPIO changes have been included as the RCAR_GP_PIN and
IRQ_TYPE_EDGE_BOTH changes are depended on by SH-PFC changes.
* tag 'renesas-pinmux-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (132 commits)
ARM: shmobile: marzen: Use RCAR_GP_PIN macro
ARM: shmobile: lager: Initialize pinmux
ARM: shmobile: bockw: add pinctrl support
ARM: shmobile: kzm9g: tidyup FSI pinctrl
ARM: shmobile: r8a7740 pinmux platform device cleanup
ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH
pinctrl: sh-pfc: r8a7779: Fix missing MOD_SEL2 entry
Revert "ARM: shmobile: Disallow PINCTRL without GPIOLIB"
pinctrl: r8a7790: add pinmux data for MMCIF and SDHI interfaces
sh-pfc: r8a7778: add MMCIF pin groups
sh-pfc: r8a7778: add HSPI pin groups
sh-pfc: r8a7778: add I2C pin groups
pinctrl: sh-pfc: fix a typo in pfc-r8a7790
pinctrl: sh-pfc: fix r8a7790 Function Select register tables
sh-pfc: r8a7778: fixup IRQ1A settings
sh-pfc: r8a7779: add Ether pin groups
sh-pfc: r8a7778: add Ether pin groups
sh-pfc: r8a7778: add VIN pin groups
sh-pfc: sh73a0: Remove function GPIOs
sh-pfc: r8a7790: Add TPU pin groups and functions
...
As hardware support for this feature is not universal for all SoCs a flag,
has_both_edge_trigger, has been added to the platform data of the driver to
allow this feature to be enabled.
The motivation for this is to allow use of the gpio-keys driver on the
lager board which is based on the r8a7790 SoC. The V2 of this patch has been
fully exercised using that driver on that board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car H1 or Gen2 GPIO interrupts are assigned per each GPIO domain,
but, Gen1 E1/M1 GPIO interrupts are shared for all GPIO domain.
gpio-rcar driver needs IRQF_SHARED flags for these.
This patch was tested on Bock-W board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Fix to return a negative error code in the irq descs alloc error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both stmpe_gpio_irq_map() and stmpe_gpio_irq_unmap() are not referenced
outside of this file, make them static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull GPIO fixes from Linus Walleij:
- An OMAP fix that makes ethernet work again.
- Fix for build problem when building the MCP23S08 driver as module.
- IRQ conflicts in the Langwell driver.
- Fix IRQ coherency issues in the MXS driver.
- Return correct errorcode on errorpath when removing GPIO chips.
* tag 'gpio-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Don't override the error code in probe error handling
gpio: mxs: Use set and clear capabilities of the gpio controller
gpio-langwell: fix irq conflicts when DT is not used
gpio: mcp23s08: Fix build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m
gpio/omap: ensure gpio context is initialised
