The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
gov_queue_work() acquires cpufreq_governor_lock to allow
cpufreq_governor_stop() to drain delayed work items possibly scheduled
on CPUs that share the policy with a CPU being taken offline.
However, the same goal may be achieved in a more straightforward way if
the policy pointer in the struct cpu_dbs_info matching the policy CPU is
reset upfront by cpufreq_governor_stop() under the timer_mutex belonging
to it and checked against NULL, under the same lock, at the beginning of
dbs_timer().
In that case every instance of dbs_timer() run for a struct cpu_dbs_info
sharing the policy pointer in question after cpufreq_governor_stop() has
started will notice that that pointer is NULL and bail out immediately
without queuing up any new work items. In turn, gov_cancel_work()
called by cpufreq_governor_stop() before destroying timer_mutex will
wait for all of the delayed work items currently running on the CPUs
sharing the policy to drop the mutex, so it may be destroyed safely.
Make cpufreq_governor_stop() and dbs_timer() work as described and
modify gov_queue_work() so it does not acquire cpufreq_governor_lock any
more.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When booting an HWP enabled system the kernel displays one "HWP enabled"
message for each cpu. The messages are superfluous since HWP is globally
enabled across all CPUs. This patch also adds an informational message
when HWP is disabled via intel_pstate=no_hwp.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The check for correct frequency being set in bL_cpufreq_set_rate is
broken when the big.LITTLE switcher is active, for two reasons.
1. The 'new_rate' variable gets overwritten before the test by the
code calculating the frequency of the old cluster.
2. The frequency returned by bL_cpufreq_get_rate will be the virtual
frequency, not the actual one the intended version of new_rate contains.
This means the function always returns an error causing an endless
stream of: "cpufreq: __target_index: Failed to change cpu frequency: -5"
As the intent is to check for errors that clk_set_rate doesn't report
lets move the check to immediately after that and directly use
clk_get_rate, rather than the arm_big_little helpers which only confuse
matters. Also, update the comment to be hopefully clearer about the
purpose of the code.
Fixes: 0a95e630b4 (cpufreq: arm_big_little: check if the frequency is set correctly)
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-opp:
PM / OPP: passing NULL to PTR_ERR()
PM / OPP: Move cpu specific code to opp/cpu.c
PM / OPP: Move opp core to its own directory
PM / OPP: Prefix exported opp routines with dev_pm_opp_
PM / OPP: Rename opp init/free table routines
PM / OPP: reuse of_parse_phandle()
* pm-cpufreq:
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
cpufreq: intel_pstate: Fix intel_pstate powersave min_perf_pct value
cpufreq: intel_pstate: Avoid calculation for max/min
Documentation: kernel_parameters for Intel P state driver
cpufreq: intel_pstate: Use ACPI perf configuration
cpufreq: intel-pstate: Use separate max pstate for scaling
cpufreq: intel_pstate: get P1 from TAR when available
cpufreq: Drop redundant check for inactive policies
cpufreq : powernv: Report Pmax throttling if capped below nominal frequency
cpufreq: imx: update the clock switch flow to support imx6ul
cpufreq: tegra20: remove superfluous CONFIG_PM ifdefs
cpufreq: conservative: remove 'enable' field
cpufreq: integrator: Fix module autoload for OF platform driver
* pm-cpuidle:
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
* acpi-processor:
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI: Allow selection of the ACPI processor driver for ARM64
CPPC: Probe for CPPC tables for each ACPI Processor object
ACPI: Add weak routines for ACPI CPU Hotplug
ACPI / CPPC: Add a CPUFreq driver for use with CPPC
ACPI: Introduce CPU performance controls using CPPC
The sysfs policy directory is postfixed currently with the CPU number
for which the policy was created, which isn't necessarily the first CPU
in related_cpus mask.
To make it more consistent and predictable, lets postfix the policy with
the first cpu in related-cpus mask.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq sysfs interface had been a bit inconsistent as one of the
CPUs for a policy had a real directory within its sysfs 'cpuX' directory
and all other CPUs had links to it. That also made the code a bit
complex as we need to take care of moving the sysfs directory if the CPU
containing the real directory is getting physically hot-unplugged.
Solve this by creating 'policyX' directories (per-policy) in
/sys/devices/system/cpu/cpufreq/ directory, where X is the CPU for which
the policy was first created.
This also removes the need of keeping kobj_cpu and we can remove it now.
Suggested-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: is more of a general agreement from the person that he is
Reviewed-by: is a more strict tag and implies that the reviewer has
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later patches will need to create policy specific directories in
/sys/devices/system/cpu/cpufreq/ directory and so the cpufreq directory
wouldn't be ever empty.
And so no fun creating/destroying it on need basis anymore. Create it
once on system boot.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
->related_cpus is empty at this point of time and copying ->cpus to it
or orring ->related_cpus with ->cpus would result in the same value. But
cpumask_copy makes it rather clear.
Reviewed-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'timer_mutex' is required to sync work-handlers of policy->cpus.
update_sampling_rate() is just canceling the works and queuing them
again. This isn't protecting anything at all in update_sampling_rate()
and is not gonna be of any use.
Even if a work-handler is already running for a CPU,
cancel_delayed_work_sync() will wait for it to finish.
Drop these unnecessary locks.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems that initialize the intel_pstate driver with the performance
governor, and then switch to the powersave governor will not transition to
lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct
is set to a low value.
The behavior of governor switching changed after commit a04759924e
("[cpufreq] intel_pstate: honor user space min_perf_pct override on
resume"). The commit introduced tracking of performance percentage
changes via sysfs in order to restore userspace changes during
suspend/resume. The problem occurs because the global values of the newly
introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor
change and this causes the powersave governor to inherit the performance
governor's settings.
A simple change would have been to reset max_sysfs_pct to 100 and
min_sysfs_pct to 0 on a governor change, which fixes the problem with
governor switching. However, since we cannot break userspace[1] the fix
is now to give each governor its own limits storage area so that governor
specific changes are tracked.
I successfully tested this by booting with both the performance governor
and the powersave governor by default, and switching between the two
governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values,
and looking at the output of cpupower frequency-info). Suspend/Resume
testing was performed by Doug Smythies.
[1] Systems which suspend/resume using the unmaintained pm-utils package
will always transition to the performance governor before the suspend and
after the resume. This means a system using the powersave governor will
go from powersave to performance, then suspend/resume, performance to
powersave. The simple change during governor changes would have been
overwritten when the governor changed before and after the suspend/resume.
I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225
against Fedora to remove the 94cpufreq file that causes the problem. It
should be noted that pm-utils is obsoleted with newer versions of systemd.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d7 (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When requested from cpufreq to set policy, look into _pss and get
control values, instead of using max/min perf calculations. These
calculation misses next control state in boundary conditions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use ACPI _PSS to limit the Intel P State turbo, max and min ratios.
This driver uses acpi processor perf lib calls to register performance.
The following logic is used to adjust Intel P state driver limits:
- If there is no turbo entry in _PSS, then disable Intel P state turbo
and limit to non turbo max
- If the non turbo max ratio is more than _PSS max non turbo value, then
set the max non turbo ratio to _PSS non turbo max
- If the min ratio is less than _PSS min then change the min ratio
matching _PSS min
- Scale the _PSS turbo frequency to max turbo frequency based on control
value.
This feature can be disabled by using kernel parameters:
intel_pstate=no_acpi
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Systems with configurable TDP have multiple max non turbo p state. Intel
P state uses max non turbo P state for scaling. But using the real max
non turbo p state causes underestimation of next P state. So using
the physical max non turbo P state as before for scaling.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After Ivybridge, the max non turbo ratio obtained from platform info msr
is not always guaranteed P1 on client platforms. The max non turbo
activation ratio (TAR), determines the max for the current level of TDP.
The ratio in platform info is physical max. The TAR MSR can be locked,
so updating this value is not possible on all platforms.
This change gets this ratio from MSR TURBO_ACTIVATION_RATIO if
available,
but also do some sanity checking to make sure that this value is
correct.
The sanity check involves reading the TDP ratio for the current tdp
control value when platform has configurable TDP present and matching
TAC
with this.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.
This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Log a 'critical' message if the max frequency is reduced below nominal
frequency. We already log 'info' message if the max frequency is
capped below turbo frequency. CPU should guarantee atleast nominal
frequency, but not turbo frequency in all system configurations and
environments. So report the pmax throttling with severity when Pmax is
dipped below nominal frequency.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For i.MX6UL, the clock switch flow is slightly different from
other i.MX6 SOCs. It has a 'secondary_sel' clk that will be used
when the CPU freq is higher than 396MHz. So the clock switch flow in
'set_target' callback need to update to support i.MX6UL in the common
i.MX6 SOC cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Conservative governor has its own 'enable' field to check if
conservative governor is used for a CPU or not
This can be checked by policy->governor with 'cpufreq_gov_conservative'
and so this field can be dropped.
Because its not guaranteed that dbs_info->cdbs.shared will a valid
pointer for all CPUs (will be NULL for CPUs that don't use
ondemand/conservative governors), we can't use it anymore. Lets get
policy with cpufreq_cpu_get_raw() instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_cpu_get() called by get_cur_freq_on_cpu() is overkill,
because the ->get() callback is always invoked in a context in
which all of the conditions checked by cpufreq_cpu_get() are
guaranteed to be satisfied.
Use cpufreq_cpu_get_raw() instead of it and drop the
corresponding cpufreq_cpu_put() from get_cur_freq_on_cpu().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
OPP code is expanding and is already present in multiple directories
(cpufreq and power). Lets move it to its own directory, to manage it
better.
This also moves/renames the cpufreq_opp file to cpu.c, as it will
contain helpers for cpu device. Its not just about cpufreq, other
frameworks can use OPPs as well.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
free-table routines are opposite of init-table ones, and must be named
to make that clear. Opposite of 'init' is 'exit', but those doesn't suit
really well.
Replace 'init' with 'add' and 'free' with 'remove'.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull more power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previous PM+ACPI
pull request (cpufreq core and drivers, cpuidle, generic power domains
framework). Some of them didn't make to that pull request and some
fix issues introduced by it.
The only really new thing is the support for suspend frequency in the
cpufreq-dt driver, but it is needed to fix an issue with Exynos
platforms.
Specifics:
- build fix for the new Mediatek MT8173 cpufreq driver (Guenter
Roeck).
- generic power domains framework fixes (power on error code path,
subdomain removal) and cleanup of a deprecated API user (Geert
Uytterhoeven, Jon Hunter, Ulf Hansson).
- cpufreq-dt driver fixes including two fixes for bugs related to the
new Operating Performance Points Device Tree bindings introduced
recently (Viresh Kumar).
- suspend frequency support for the cpufreq-dt driver (Bartlomiej
Zolnierkiewicz, Viresh Kumar).
- cpufreq core cleanups (Viresh Kumar).
- intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi).
- additional sanity check in the cpuidle core (Xunlei Pang).
- fix for a comment related to CPU power management (Lina Iyer)"
* tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
PM / OPP: Return suspend_opp only if it is enabled
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
PM / OPP: add dev_pm_opp_get_suspend_opp() helper
staging: board: Migrate away from __pm_genpd_name_add_device()
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
PM / Domains: Ensure subdomain is not in use before removing
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpuidle/coupled: Add sanity check for safe_state_index
PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
kernel/cpu_pm: fix cpu_cluster_pm_exit comment
* pm-cpufreq:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
PCT_TO_HWP does not take the actual range of pstates exported
by HWP_CAPABILITIES in account, and is broken on most platforms.
Remove the macro and set the min and max pstate for hwp by
determining the range and adjusting by the min and max percent
limits values.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In current code, max_perf_pct might be smaller than min_perf_pct
by improper user input:
$ grep . /sys/devices/system/cpu/intel_pstate/m*_perf_pct
/sys/devices/system/cpu/intel_pstate/max_perf_pct:100
/sys/devices/system/cpu/intel_pstate/min_perf_pct:100
$ echo 80 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ grep . /sys/devices/system/cpu/intel_pstate/m*_perf_pct
/sys/devices/system/cpu/intel_pstate/max_perf_pct:80
/sys/devices/system/cpu/intel_pstate/min_perf_pct:100
Fix this problem by 2 steps:
1. Normalize the user input to [min_policy, max_policy].
2. Make sure max_perf_pct>=min_perf_pct, suggested by Seiichi Ikarashi.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add suspend frequency support and if needed set it to
the frequency obtained from the suspend opp (can be defined
using opp-v2 bindings and is optional).
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cpufreq drivers may set suspend frequency only for
selected setups but still would like to use the generic
suspend handler. Thus don't treat !policy->suspend_freq
condition as an incorrect one.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Its better to use __func__ to print functions name instead of writing
the name in the print statement. This also has the advantage that a
change in function's name doesn't force us to change the print message
as well.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If ARM_MT8173_CPUFREQ is configured, and THERMAL is configured as module,
the following build error is seen for arm:allmodconfig and
arm64:allmodconfig.
drivers/built-in.o: In function `mtk_cpufreq_ready':
:(.text+0x32a20c): undefined reference to `of_cpufreq_cooling_register'
drivers/built-in.o: In function `mtk_cpufreq_exit':
:(.text+0x32a420): undefined reference to `cpufreq_cooling_unregister'
The fix is similar to CPUFREQ_DT, but more restrictive since
ARM_MT8173_CPUFREQ can not be built as module.
Fixes: 1453863fb0 ("cpufreq: mediatek: Add MT8173 cpufreq driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tolerance applies on both sides of the target voltage, i.e. both min and
max sides. But while checking if a voltage is supported by the regulator
or not, we haven't taken care of tolerance on the lower side. Fix that.
Cc: Lucas Stach <l.stach@pengutronix.de>
Fixes: 045ee45c4f ("cpufreq: cpufreq-dt: disable unsupported OPPs")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. This operation can potentially fail, and in that
case we should at least print an error message.
Fixes: 2e02d8723e ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need to explicitly mark OPPs as shared, when they are not defined
with OPP-v2 bindings. But this isn't required to be done if we failed to
initialize OPP table.
Reorder code to verify OPP count before marking them shared.
Fixes: 2e02d8723e ("cpufreq: dt: Add support for operating-points-v2 bindings")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
