The ARM IM-PD1 add-on module has a few clock of its own, let's
move also these down to the drivers/clk/versatile driver dir
and get rid of any remaining oldschool Integrator clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It turns out that all platforms using the ICST VCO are really
just touching two registers, and in the same way as well: one
register with the VCO configuration as such, and one lock register
that makes it possible to write to the VCO.
Factor this register read/write into the ICST driver so we can
reuse it in the IM-PD1 driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The GPLv2 headers were missing and the subsystem maintainer likes
them so put them in. I am the copyright holder, so explicitly
licensing these under the GPLv2.
Reported-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
From Mike Turquette:
* depends/clk:
clk: Common clocks implementation for Versatile Express
clk: Versatile Express clock generators ("osc") driver
CLK: clk-twl6040: Initial clock driver for OMAP4+ McPDM fclk clock
clk: fix return value check in sirfsoc_of_clk_init()
clk: fix return value check in of_fixed_clk_setup()
clk: ux500: Update sdmmc clock to 100MHz for u8500
clk: ux500: Support prcmu ape opp voltage clock
mfd: dbx500: Export prmcu_request_ape_opp_100_voltage
clk: Don't return negative numbers for unsigned values with !clk
clk: Fix documentation typos
clk: Document .is_enabled op
clk: SPEAr: Vco-pll: Fix compilation warning
This driver allows to provide DT clocks for clock gates found on
Marvell Dove and Kirkwood SoCs. The clock gates are referenced by
the phandle index of the corresponding bit in the clock gating control
register to ease lookup in the datasheet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes compile error if one of SPEAr3xx implementations is not selected.
CC drivers/clk/spear/spear3xx_clock.o
drivers/clk/spear/spear3xx_clock.c: In function 'spear3xx_clk_init':
drivers/clk/spear/spear3xx_clock.c:599:3: error: implicit declaration of function 'spear300_clk_init' [-Werror=implicit-function-declaration]
drivers/clk/spear/spear3xx_clock.c:601:3: error: implicit declaration of function 'spear310_clk_init' [-Werror=implicit-function-declaration]
drivers/clk/spear/spear3xx_clock.c:603:3: error: implicit declaration of function 'spear320_clk_init' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/clk/spear/spear3xx_clock.o] Error 1
make[2]: *** [drivers/clk/spear] Error 2
make[1]: *** [drivers/clk] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Nomadik NAND driver is really just a subset of the existing
FSMC driver, so let's switch over to using that driver instead,
since it handles more variants of this chip. The callbacks for
setting up the chip is doing stuff now handled by the FSMC
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Provide simplified models for the necessary clocks on the zynq-7000
platform. Currently, the PLLs, the CPU clock network, and the basic
peripheral clock networks (for SDIO, SMC, SPI, QSPI, UART) are modelled.
OF bindings are also provided and documented.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This patch adds some additional handling for the SDMMC special case
in round_rate and set_rate which results in invalid divisor messages
at boot time.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The new armss clk is a prcmu_scalable_rate clk which represents
the ARMSS clk. This then makes it possible to convert the smp_twd
clk to a fixed factor clock type, using a fixed divider of 2 and
with the armss clk as parent.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The ux500 clock driver file named u8500_clk.c does not compile
if it loose implicit dependencies to <mach/db8500-regs.h>
(I have no clue what files will include this) which manifests
itself as I'm experimenting with SPARSE_IRQ so make the
dependency explicit.
Cc: Mike Turquette <mturquette@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some clock drivers can be simplified if devres takes care of
unregistering any registered clocks along error paths. Introduce
devm_clk_register() so that clock drivers get unregistration for
free along with simplified error paths.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a DT and non-DT based implementation of
the common clock infrastructure for Versatile Express
platform. It registers (statically or using DT) all
required fixed clocks, initialises motherboard's SP810
cell (that provides clocks for SP804 timers) and
explicitly registers VE "osc" driver, to make the
clock generators available early.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This driver provides a common clock framework hardware driver
for Versatile Express clock generators (a.k.a "osc") controlled
via the config bus.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() not NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
For u8500 and using 100MHz as the frequency also requires the ape opp 100
voltage, thus use the prcmu_opp_volt_scalable clock type.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some scalable prcmu clocks needs to be handled in conjuction with the
ape opp 100 voltage. A new prcmu clock type clk_prcmu_opp_volt_scalable
is implemented to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of the helper functions return negative error codes if
passed a NULL clock. This can lead to confusing behavior when the
expected return value is unsigned. Fix up these accessors so that
they return unsigned values (or bool in the case of is_enabled).
This way we can't interpret NULL clocks as having valid and
interesting values.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently we are getting following warning for SPEAr clk-vco-pll.
"warning: i is used uninitialized in this function."
This is because we are getting value of i by passing its pointer to another
routine.
The variables here are really not used uninitialized.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Pull ARM soc-specific updates, take 2 from Olof Johansson:
"This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: remove mach/irqs.h
ARM: mxs: select SPARSE_IRQ
ARM: mxs: adopt irq_domain support for icoll driver
ARM: mxs: select MULTI_IRQ_HANDLER
ARM: mxs: retrieve timer irq from device tree
gpio/mxs: adopt irq_domain support for mxs gpio driver
