On certain cores (namely proAptiv and P5600) incoming data via a Fast
Debug Channel (FDC) while the core is blocked on a wait instruction will
cause the wait not to wake up even when another interrupt is received.
This makes an idle target stop as soon as you send FDC data to it, until
the debug probe interrupts it and restarts the wait instruction.
This is worked around by avoiding using r4k_wait on these cores if
CONFIG_MIPS_EJTAG_FDC_TTY is enabled (which would imply the user intends
to use the FDC).
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Read the CPU IRQ line reportedly used for the Fast Debug Channel (FDC)
interrupt from the IntCtl register and store it in cp0_fdc_irq where
platform implementations of the new weak platform function
get_c0_fdc_int() can refer to it.
[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9140/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.
Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.
Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.
A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add architectural definitions and probing for the MIPS Common Device
Memory Map (CDMM) region. When supported and enabled at a particular
physical address, this region allows some number of per-CPU devices to
be discovered and controlled via MMIO.
A bit exists in Config3 to determine whether the feature is present, and
a CDMMBase CP0 register allows the region to be enabled at a particular
physical address.
[ralf@linux-mips.org: Sort conflict with other patches.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before release 2 of the architecture there weren't separate interrupt
pending bits for the local CPU interrupts (timer & perf counter
overflow), so when they were connected to the same interrupt line the
timer handler had to call the performance counter handler before knowing
whether a timer interrupt was actually pending.
Now another CPU local interrupt, for the Fast Debug Channel (FDC), can
also be routed to an arbitrary interrupt line. It isn't scalable to keep
adding cross-calls between handlers for these cases of shared interrupt
lines, especially since the FDC could in theory share its interrupt line
with the performance counter, timer, or both.
Fortunately since release 2 of the architecture separate interrupt
pending bits do exist in the Cause register. This allows local
interrupts which share an interrupt line to have separate handlers using
IRQF_SHARED. Unfortunately they can't easily have their own irqchip as
there is no generic way to individually mask them.
Enable this sharing to happen by removing the special case for when the
perf count shares an IRQ with the timer. cp0_perfcount_irq and
cp0_compare_irq can then be set to the same value with shared interrupt
handlers registered for both of them.
Pre-R2 code should be unaffected. cp0_perfcount_irq will always be -1
and the timer handler will contnue to call into the perf counter
handler.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9131/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When requesting the performance counter overflow interrupt, pass flags
which are compatible with the cevt-r4k driver, in particular
IRQF_SHARED so that the two handlers can share the same IRQ. This is
possible since release 2 of the architecture where there are separate
pending interrupt bits for the timer interrupt and the performance
counter interrupt.
This will be necessary since the FDC interrupt can also be arbitrarily
routed to a CPU interrupt, possibly sharing with the timer, the
performance counters, or both, and it isn't scalable to have all the
handlers able to call other handlers that may be on the same IRQ line.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: oprofile-list@lists.sf.net
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9130/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When requesting the performance counter overflow interrupt, pass flags
which are compatible with the cevt-r4k driver, in particular
IRQF_SHARED so that the two handlers can share the same IRQ. This is
possible since release 2 of the architecture where there are separate
pending interrupt bits for the timer interrupt and the performance
counter interrupt.
This will be necessary since the FDC interrupt can also be arbitrarily
routed to a CPU interrupt, possibly sharing with the timer, the
performance counters, or both, and it isn't scalable to have all the
handlers able to call other handlers that may be on the same IRQ line.
Shared handlers must also have a unique device pointer so they can be
individually removed, so &mipspmu is now passed in for that instead of
NULL.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The attempt to get gcc to generate best possible code turned
c0_compare_interrupt() into a bit of Italian pasta code. Tweak for
sanity.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the cevt-r4k interrupt handler shared so that other interrupt
handlers (specifically the performance counter overflow handler and fast
debug channel interrupt handler) can share the same interrupt line.
This simply imvolves returning IRQ_NONE when no timer interrupt has been
handled to allow other handlers to run, and passing IRQF_SHARED when
setting up the IRQ handler so that other handlers (with compatible
flags) can be registered.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Long ago, commit 8531a35e5e ("[MIPS] SMTC: Fix SMTC dyntick support.")
moved handle_perf_irq() out of cevt-r4k.c into a header so it could be
shared with cevt-smtc.c.
Slightly less long ago, commit b633648c5a ("MIPS: MT: Remove SMTC
support") removed all traces of SMTC support, including cevt-smtc.c,
leaving cevt-r4k.c once again the sole user of handle_perf_irq(),
therefore move it back into cevt-r4k.c from the header.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9123/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the code is in place for KVM to support MIPS SIMD Architecutre
(MSA) in MIPS guests, wire up the new KVM_CAP_MIPS_MSA capability.
For backwards compatibility, the capability must be explicitly enabled
in order to detect or make use of MSA from the guest.
The capability is not supported if the hardware supports MSA vector
partitioning, since the extra support cannot be tested yet and it
extends the state that the userland program would have to save.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add KVM register numbers for the MIPS SIMD Architecture (MSA) registers,
and implement access to them with the KVM_GET_ONE_REG / KVM_SET_ONE_REG
ioctls when the MSA capability is enabled (exposed in a later patch) and
present in the guest according to its Config3.MSAP bit.
The MSA vector registers use the same register numbers as the FPU
registers except with a different size (128bits). Since MSA depends on
Status.FR=1, these registers are inaccessible when Status.FR=0. These
registers are returned as a single native endian 128bit value, rather
than least significant half first with each 64-bit half native endian as
the kernel uses internally.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add guest exception handling for MIPS SIMD Architecture (MSA) floating
point exceptions and MSA disabled exceptions.
MSA floating point exceptions from the guest need passing to the guest
kernel, so for these a guest MSAFPE is emulated.
MSA disabled exceptions are normally handled by passing a reserved
instruction exception to the guest (because no guest MSA was supported),
but the hypervisor can now handle them if the guest has MSA by passing
an MSA disabled exception to the guest, or if the guest has MSA enabled
by transparently restoring the guest MSA context and enabling MSA and
the FPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Emulate MSA related parts of COP0 interface so that the guest will be
able to enable/disable MSA (Config5.MSAEn) once the MSA capability has
been wired up.
As with the FPU (Status.CU1) setting Config5.MSAEn has no immediate
effect if the MSA state isn't live, as MSA state is restored lazily on
first use. Changes after the MSA state has been restored take immediate
effect, so that the guest can start getting MSA disabled exceptions
right away for guest MSA operations. The MSA state is saved lazily too,
as MSA may get re-enabled in the near future anyway.
A special case is also added for when Status.CU1 is set while FR=0 and
the MSA state is live. In this case we are at risk of getting reserved
instruction exceptions if we try and save the MSA state, so we lose the
MSA state sooner while MSA is still usable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add base code for supporting the MIPS SIMD Architecture (MSA) in MIPS
KVM guests. MSA cannot yet be enabled in the guest, we're just laying
the groundwork.
As with the FPU, whether the guest's MSA context is loaded is stored in
another bit in the fpu_inuse vcpu member. This allows MSA to be disabled
when the guest disables it, but keeping the MSA context loaded so it
doesn't have to be reloaded if the guest re-enables it.
New assembly code is added for saving and restoring the MSA context,
restoring only the upper half of the MSA context (for if the FPU context
is already loaded) and for saving/clearing and restoring MSACSR (which
can itself cause an MSA FP exception depending on the value). The MSACSR
is restored before returning to the guest if MSA is already enabled, and
the existing FP exception die notifier is extended to catch the possible
MSA FP exception and step over the ctcmsa instruction.
The helper function kvm_own_msa() is added to enable MSA and restore
the MSA context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use MSA for the first time and
triggers an MSA disabled exception.
The existing FPU helpers are extended to handle MSA. kvm_lose_fpu()
saves the full MSA context if it is loaded (which includes the FPU
context) and both kvm_lose_fpu() and kvm_drop_fpu() disable MSA.
kvm_own_fpu() also needs to lose any MSA context if FR=0, since there
would be a risk of getting reserved instruction exceptions if CU1 is
enabled and we later try and save the MSA context. We shouldn't usually
hit this case since it will be handled when emulating CU1 changes,
however there's nothing to stop the guest modifying the Status register
directly via the comm page, which will cause this case to get hit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add KVM register numbers for the MIPS FPU registers, and implement
access to them with the KVM_GET_ONE_REG / KVM_SET_ONE_REG ioctls when
the FPU capability is enabled (exposed in a later patch) and present in
the guest according to its Config1.FP bit.
The registers are accessible in the current mode of the guest, with each
sized access showing what the guest would see with an equivalent access,
and like the architecture they may become UNPREDICTABLE if the FR mode
is changed. When FR=0, odd doubles are inaccessible as they do not exist
in that mode.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add guest exception handling for floating point exceptions and
coprocessor 1 unusable exceptions.
Floating point exceptions from the guest need passing to the guest
kernel, so for these a guest FPE is emulated.
Also, coprocessor 1 unusable exceptions are normally passed straight
through to the guest (because no guest FPU was supported), but the
hypervisor can now handle them if the guest has its FPU enabled by
restoring the guest FPU context and enabling the FPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Emulate FPU related parts of COP0 interface so that the guest will be
able to enable/disable the following once the FPU capability has been
wired up:
- The FPU (Status.CU1)
- 64-bit FP register mode (Status.FR)
- Hybrid FP register mode (Config5.FRE)
Changing Status.CU1 has no immediate effect if the FPU state isn't live,
as the FPU state is restored lazily on first use. After that, changes
take place immediately in the host Status.CU1, so that the guest can
start getting coprocessor unusable exceptions right away for guest FPU
operations if it is disabled. The FPU state is saved lazily too, as the
FPU may get re-enabled in the near future anyway.
Any change to Status.FR causes the FPU state to be discarded and FPU
disabled, as the register state is architecturally UNPREDICTABLE after
such a change. This should also ensure that the FPU state is fully
initialised (with stale state, but that's fine) when it is next used in
the new FP mode.
Any change to the Config5.FRE bit is immediately updated in the host
state so that the guest can get the relevant exceptions right away for
single-precision FPU operations.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add base code for supporting FPU in MIPS KVM guests. The FPU cannot yet
be enabled in the guest, we're just laying the groundwork.
Whether the guest's FPU context is loaded is stored in a bit in the
fpu_inuse vcpu member. This allows the FPU to be disabled when the guest
disables it, but keeping the FPU context loaded so it doesn't have to be
reloaded if the guest re-enables it.
An fpu_enabled vcpu member stores whether userland has enabled the FPU
capability (which will be wired up in a later patch).
New assembly code is added for saving and restoring the FPU context, and
for saving/clearing and restoring FCSR (which can itself cause an FP
exception depending on the value). The FCSR is restored before returning
to the guest if the FPU is already enabled, and a die notifier is
registered to catch the possible FP exception and step over the ctc1
instruction.
The helper function kvm_lose_fpu() is added to save FPU context and
disable the FPU, which is used when saving hardware state before a
context switch or KVM exit (the vcpu_get_regs() callback).
The helper function kvm_own_fpu() is added to enable the FPU and restore
the FPU context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use the FPU for the first time
and triggers a co-processor unusable exception.
The helper function kvm_drop_fpu() is added to discard the FPU context
and disable the FPU, which will be used in a later patch when the FPU
state will become architecturally UNPREDICTABLE (change of FR mode) to
force a reload of [stale] context in the new FR mode.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add a vcpu_get_regs() and vcpu_set_regs() callbacks for loading and
restoring context which may be in hardware registers. This may include
floating point and MIPS SIMD Architecture (MSA) state which may be
accessed directly by the guest (but restored lazily by the hypervisor),
and also dedicated guest registers as provided by the VZ ASE.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Add Config4 and Config5 co-processor 0 registers, and add capability to
write the Config1, Config3, Config4, and Config5 registers using the KVM
API.
Only supported bits can be written, to minimise the chances of the guest
being given a configuration from e.g. QEMU that is inconsistent with
that being emulated, and as such the handling is in trap_emul.c as it
may need to be different for VZ. Currently the only modification
permitted is to make Config4 and Config5 exist via the M bits, but other
bits will be added for FPU and MSA support in future patches.
Care should be taken by userland not to change bits without fully
handling the possible extra state that may then exist and which the
guest may begin to use and depend on.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Clean up KVM_GET_ONE_REG / KVM_SET_ONE_REG register definitions for
MIPS, to prepare for adding a new group for FPU & MSA vector registers.
Definitions are added for common bits in each group of registers, e.g.
KVM_REG_MIPS_CP0 = KVM_REG_MIPS | 0x10000, for the coprocessor 0
registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Trap instructions are used by Linux to implement BUG_ON(), however KVM
doesn't pass trap exceptions on to the guest if they occur in guest
kernel mode, instead triggering an internal error "Exception Code: 13,
not yet handled". The guest kernel then doesn't get a chance to print
the usual BUG message and stack trace.
Implement handling of the trap exception so that it gets passed to the
guest and the user is left with a more useful log message.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
When handling floating point exceptions (FPEs) and MSA FPEs the Cause
bits of the appropriate control and status register (FCSR for FPEs and
MSACSR for MSA FPEs) are read and cleared before enabling interrupts,
presumably so that it doesn't have to go through the pain of restoring
those bits if the process is pre-empted, since writing those bits would
cause another immediate exception while still in the kernel.
The bits aren't normally ever restored again, since userland never
expects to see them set.
However for virtualisation it is necessary for the kernel to be able to
restore these Cause bits, as the guest may have been interrupted in an
FP exception handler but before it could read the Cause bits. This can
be done by registering a die notifier, to get notified of the exception
when such a value is restored, and if the PC was at the instruction
which is used to restore the guest state, the handler can step over it
and continue execution. The Cause bits can then remain set without
causing further exceptions.
For this to work safely a few changes are made:
- __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause
bits, and now return from exception level with interrupts disabled
instead of enabled.
- do_fpe() now clears the Cause bits and enables interrupts after
notify_die() is called, so that the notifier can chose to return from
exception without this happening.
- do_msa_fpe() acts similarly, but now actually makes use of the second
argument (msacsr) and calls notify_die() with the new DIE_MSAFP,
allowing die notifiers to be informed of MSA FPEs too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Guest user mode can generate a guest MSA Disabled exception on an MSA
capable core by simply trying to execute an MSA instruction. Since this
exception is unknown to KVM it will be passed on to the guest kernel.
However guest Linux kernels prior to v3.15 do not set up an exception
handler for the MSA Disabled exception as they don't support any MSA
capable cores. This results in a guest OS panic.
Since an older processor ID may be being emulated, and MSA support is
not advertised to the guest, the correct behaviour is to generate a
Reserved Instruction exception in the guest kernel so it can send the
guest process an illegal instruction signal (SIGILL), as would happen
with a non-MSA-capable core.
Fix this as minimally as reasonably possible by preventing
kvm_mips_check_privilege() from relaying MSA Disabled exceptions from
guest user mode to the guest kernel, and handling the MSA Disabled
exception by emulating a Reserved Instruction exception in the guest,
via a new handle_msa_disabled() KVM callback.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.15+
The expected semantics of __enable_fpu are for the FPU to be enabled
in the given mode if possible, otherwise for the FPU to be left
disabled and SIGFPE returned. The FPU was incorrectly being left
enabled in cases where the desired value for FR was unavailable.
Without ensuring the FPU is disabled in this case, it would be
possible for userland to go on to execute further FP instructions
natively in the incorrect mode, rather than those instructions being
trapped & emulated as they need to be.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a ptracee has not used the FPU and the ptracer sets its FP context
using PTRACE_POKEUSR, PTRACE_SETFPREGS or PTRACE_SETREGSET then that
context will be discarded upon either the ptracee using the FPU or a
further write to the context via ptrace. Prevent this loss by recording
that the task has "used" math once its FP context has been written to.
The context initialisation code that was present for the PTRACE_POKEUSR
case is reused for the other 2 cases to provide consistent behaviour
for the different ptrace requests.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When running the emulator to handle an instruction that raised an FP
unimplemented operation exception, the FCSR cause bits were being
cleared. This is done to ensure that the kernel does not take an FP
exception when later restoring FP context to registers. However, this
was not being done when the emulator is invoked in response to a
coprocessor unusable exception. This happens in 2 cases:
- There is no FPU present in the system. In this case things were
OK, since the FP context is never restored to hardware registers
and thus no FP exception may be raised when restoring FCSR.
- The FPU could not be configured to the mode required by the task.
In this case it would be possible for the emulator to set cause
bits which are later restored to hardware if the task migrates
to a CPU whose associated FPU does support its mode requirements,
or if the tasks FP mode requirements change.
Consistently clear the cause bits after invoking the emulator, by moving
the clearing to process_fpemu_return and ensuring this is always called
before the tasks FP context is restored. This will make it easier to
catch further paths invoking the emulator in future, as will be
introduced in further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Much like for traditional scalar FP exceptions, the cause bits in the
MSACSR register need to be cleared following an MSA FP exception.
Without doing so the exception will simply be raised again whenever
the kernel restores MSACSR from a tasks saved context, leading to
undesirable spurious exceptions. Clear the cause bits from the
handle_msa_fpe function, mirroring the way handle_fpe clears the
cause bits in FCSR.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Uses of the cfcmsa & ctcmsa instructions were not being wrapped by a
macro in the case where the toolchain supports MSA, since the arguments
exactly match a typical use of the instructions. However using current
toolchains this leads to errors such as:
arch/mips/kernel/genex.S:437: Error: opcode not supported on this processor: mips32r2 (mips32r2) `cfcmsa $5,1'
Thus uses of the instructions must be in the context of a ".set msa"
directive, however doing that from the users of the instructions would
be messy due to the possibility that the toolchain does not support
MSA. Fix this by renaming the macros (prepending an underscore) in order
to avoid recursion when attempting to emit the instructions, and provide
implementations for the TOOLCHAIN_SUPPORTS_MSA case which ".set msa" as
appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recursive macros made the code more concise & worked great for the
case where the toolchain doesn't support MSA. However, with toolchains
which do support MSA they lead to build failures such as:
arch/mips/kernel/r4k_switch.S: Assembler messages:
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w(0+1)[2],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w(0+1)[3],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w((0+1)+1)[2],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w((0+1)+1)[3],$1'
...
Drop the recursion from msa_init_all_upper invoking the msa_init_upper
macro explicitly for each vector register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Assuming at ($1) as the source or destination register of copy or
insert instructions:
- Simplifies the macros providing those instructions for toolchains
without MSA support.
- Avoids an unnecessary move instruction when at is used as the source
or destination register anyway.
- Is sufficient for the uses to be introduced in the kernel by a
subsequent patch.
Note that due to a patch ordering snafu on my part this also fixes the
currently broken build with MSA support enabled. The build has been
broken since commit c9017757c5 "MIPS: init upper 64b of vector
registers when MSA is first used", which this patch should have
preceeded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9161/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The {save,restore}_fp_context{,32} functions require that the assembler
allows the use of sdc instructions on any FP register, and this is
acomplished by setting the arch to mips64r2 or mips64r6
(using MIPS_ISA_ARCH_LEVEL_RAW).
However this has the effect of enabling the assembler to use mips64
instructions in the expansion of pseudo-instructions. This was done in
the (now-reverted) commit eec43a224c "MIPS: Save/restore MSA context
around signals" which led to my mistakenly believing that there was an
assembler bug, when in reality the assembler was just emitting mips64
instructions. Avoid the issue for future commits which will add code to
r4k_fpu.S by pushing the .set MIPS_ISA_ARCH_LEVEL_RAW directives into
the functions that require it, and remove the spurious assertion
declaring the assembler bug.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[james.hogan@imgtec.com: Rebase on v4.0-rc1 and reword commit message to
reflect use of MIPS_ISA_ARCH_LEVEL_RAW]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9612/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
