This patch adds device tree bindings for OMAP OneNAND devices.
Tested on an OMAP3 3430 IGEPv2 board.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc_onenand_init() will be called from another driver's probe() function,
so drop the __init annotation, in order to prevent section mismatches.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the GPMC probe fails, devices that use the GPMC (such as ethernet
chips, flash memories, etc) can still allocate a GPMC chip-select and
register the device. On the OMAP2420 H4 board, this was causing the
kernel to crash after the gpmc probe failed and the board attempted
to start networking. Prevent this by marking all the chip-selects as
reserved by default and only make them available for devices to request
if the GPMC probe succeeds.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCDC clock node is a one that does not have set rate capability. It
just passes on the rate that is sent downstream by it's parent. While
lcdc clock parent and it's grand parent - dpll_disp_m2_ck and
dpll_disp_ck has the capability to configure rate.
And the default rates provided by LCDC clock's ancestors are not
sufficient to obtain pixel clock for current LCDC use cases, hence
currently display would not work on AM335x SoC's (with driver
modifications in platfrom independent way).
Hence inform clock framework to propogate set rate for LCDC clock as
well as it's parent - dpll_disp_m2_ck. With this change, set rate on
LCDC clock would get propogated till dpll_disp_ck via dpll_disp_m2_ck,
hence allowing the driver (same driver is used in DaVinci too) to set
rates using LCDC clock without worrying about platform dependent clock
details.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DEFINE_STRUCT_CLK does not have the capability to set flags, define
DEFINE_STRUCT_CLK_FLAGS to handle flags. This is needed to add
SET_RATE_PARENT flag in statically defined lcd clock in am335x.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The core functionality of the arch_timer driver is not directly tied to
anything under arch/arm, and can be split out.
This patch factors out the core of the arch_timer driver, so it can be
shared with other architectures. A couple of functions are added so
that architecture-specific code can interact with the driver without
needing to touch its internals.
The ARM_ARCH_TIMER config variable is moved out to
drivers/clocksource/Kconfig, existing uses in arch/arm are replaced with
HAVE_ARM_ARCH_TIMER, which selects it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix some whitespace problems introduced by commit
da03ce65b5 ("OMAP3: powerdomain data:
add voltage domains"). Also, improve the documentation for the struct
powerdomain.flags field.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The atomic usecounts seem to be confusing, and are no longer needed
since the operations that they are attached to really should take
place under lock. Replace the atomic counters with simple integers,
protected by the enclosing powerdomain spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Split the clkdm_(add|del)_(wk|sleep)dep() functions into lockless and
locking versions -- this will be needed in a subsequent patch. Also,
while here, remove the leading underscore, since these are not
currently static functions. And for functions that have
kerneldoc-style comment blocks, but which are missing the initial
'/**' tag, fix the tag to indicate that they are kerneldoc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no need to preserve the autodep handling code in
mach-omap2/cm2xxx.c, since no autodeps are defined for these chips.
Hopefully they'll never be needed, but if in some future case they are,
this code can be added back in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a per-powerdomain spinlock. Use that instead of the clockdomain
spinlock. Add pwrdm_lock()/pwrdm_unlock() functions to allow other
code to acquire or release the powerdomain spinlock without reaching
directly into the struct powerdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Move omap_set_pwrdm_state() from the PM code to the powerdomain code,
and refactor it to split it up into several functions. A subsequent patch
will rename it to conform with the existing powerdomain function names.
This version includes some additional documentation, based on a
suggestion from Jean Pihet. It also modifies omap_set_pwrdm_state()
to not bail out early unless both the powerdomain current power state
and the next power state are equal. (Previously it would terminate
early if the next power state was equal to the target power state,
which was insufficiently rigorous.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tero Kristo <t-kristo@ti.com>
Drop an unnecessary pwrdm_wait_transition() from mach-omap2/pm.c -
it's called by the subsequent pwrdm_state_switch().
Also get rid of pwrdm_wait_transition() in the powerdomain code - there's
no longer any need to export this function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Don't attempt to put clockdomains to sleep; this should be handled by the
clock framework. It should be enough to program the next-power-state,
and then let the code in omap_pm_clkdms_setup() deal with the rest.
Start out by programming the MPU and CORE powerdomains to stay ON.
Then control the MPU and CORE powerdomain states directly in
omap2_enter_full_retention() and omap2_enter_mpu_retention(). Not the
most optimal way to do it, but certainly is the most conservative until
OMAP2xxx PM is working again.
Get rid of the open-coded PM_PWSTCTRL_MPU writes in
omap2_enter_mpu_retention(); use the powerdomain code instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In clkdm_sleep(), the powerdomain should be eligible to switch power
states right after the call to the low-level clockdomain sleep
function. We should have been tracking that with the
pwrdm_state_switch() code, but we weren't, for whatever reason. Fix that.
This resolves the "pwrdm state mismatch(cam_pwrdm) 3 != 0" that appears
during the OMAP4460 Pandaboard-ES PM test, e.g. here:
http://www.pwsan.com/omap/testlogs/test_v3.8-rc5/20130126003323/pm/4460pandaes/4460pandaes_log.txt
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fix the trace in the case a power domain did not hit the desired
state, as reported by Paul Walmsley.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
[paul@pwsan.com: split this fix off from the patch
"ARM: OMAP2+: PM debug: trace the functional power domains states"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoid programming the MPU and CORE powerdomain next-power-state
registers if those powerdomains will never enter low-power states
(e.g., the state that people refer to as "C1").
To avoid making assumptions about CPUIdle states based on their order
in the list, use a flag to mark CPUIdle states that don't enter
powerdomain low-power states.
Avoid a previous-power-state register read on the MPU powerdomain
unless we know that the MPU was supposed to go OFF during the last
state transition. Previous-power-state register reads can be very
expensive, so it's worth avoiding these when possible.
Since the CORE_L3 clockdomain can't go inactive unless the MPU is active,
there's little point blocking autoidle on the CORE_L3 clockdomain in "C1"
state, since we've programmed the MPU clockdomain to stay active.
Remove the unnecessary code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Drop the define and make use of scu_a9_get_base() which reads
the physical address of SCU from CP15 register.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This driver is simple, uses the latest interfaces and contains few if
any controversial elements. All of its interfaces have been in place
for a long time now. Hence let's move it out of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Use the HWMOD_BLOCK_WFI flag in the hwmod data to prevent the MPU from
entering WFI when the I2C devices are active. No idea why this is needed;
this could certainly bear further investigation if anyone is interested.
The objective here is to remove some custom code from the OMAP24xx PM
code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Apparently, on some OMAPs, the MPU can't be allowed to enter WFI while
certain peripherals are active. It's not clear why, and it's likely
that there is simply some other bug in the driver or integration code.
But since the likelihood that anyone will have the time to track these
problems down in the future seems quite small, we'll provide a
flag, HWMOD_BLOCK_WFI, to mark these issues in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3xxx CPUIdle driver contains some code to place a lower bound
on the PER powerdomain's power state. Convert this code to a data-driven
implementation to remove branches and to improve readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add the possible logic retention states for the 24xx CORE powerdomain.
Subsequent patches use this data to avoid returning incorrect data, by
skipping reads from register bitfields that don't actually exist.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove some clocks that don't appear to be used by anything
and which are not associated with any hardware registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Convert all DEFINE_OMAP_MUX_GATE() combinations that list MODULEMODE
registers in their gate arguments to DEFINE_OMAP_MUX(), dropping the
MODULEMODE data. This is possible because the MODULEMODE bits control
IP blocks, not clocks; and the hwmod code takes care of IP block
control. Rename these clocks to reflect the original multiplexer name
as specified in the comments. And convert the hwmod data to use the
multiplexer clock name.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove some leaf "clocks" that are actually IP block idle control
points, since these should now be handled by the hwmod code.
There are still a few types of MODULEMODE clocks that need to be
cleaned up:
- those still in use by driver or integration code
- those in DEFINE_CLK_OMAP_MUX_GATE() blocks; the gate portion of
these should be removed
A similar process may also be possible on OMAP2/3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove now-obsolete code from arch/arm/mach-omap2/omap_device.c. This
mostly consists of removing the first attempt at device PM latency
handling. This was never really used, has been replaced by the common
dev_pm_qos code, and needs to go away as part of the DT conversion.
Also, the early platform_device creation code has been removed, as it
appears to be unused.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cam_mclk clock is generated through the following clocks chain:
dpll4 -> dpll4_m5 -> dpll4_m5x2 -> cam_mclk
As dpll4_m5 and dpll4_m5x2 do not driver any clock other than cam_mclk,
back-propagate the cam_clk rate changes up to dpll4_m5.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
The pin in question is muxed between GPIO7 and PWM1. For backlight control
there is a custom code in board-zoom-display to control the backlight.
No need to request the GPIO7 - which was failing since the way it is
requested no longer valid: twl's gpio range is allocated dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
With the PWM backed driver the PMU_STAT led's brighness can be controlled.
This needs the new drivers for the TWL PWM/LED to work.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
New PWM drivers are being prepared for twl series which will enable the use
of all PWMs (PWMs and LEDs).
They are implemented as generic PWM drivers to be able to use them for different
purposes.
The current platform code was broken: the leds_pwm driver was not able to pick
up the PWM since the pwm_id was incorrect.
With the other patches we will be able to control the followings:
LCD backlight via pwm-backlight driver
Keypad leds via leds_pwm driver as normal LED
Charging indicator via leds_pwm driver as normal LED
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Boards with special audio routing can pass a custom omap_tw4030_pdata to the
audio machine driver.
At the same time update the board files using the same audio driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Select the most commonly used audio configuration on boards with twl4030
audio:
Headset, Handsfree output and Line in input
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
