Add the new defines for DRA7xx prm module registers.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation in the comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes for 3.11 are still trickling in. These are:
- A couple of fixes for older OMAP platforms
- Another few fixes for at91 (lateish due to European summer
vacations)
- A late-found problem with USB on Tegra, fix is to keep VBUS
regulator on at all times
- One fix for Exynos 5440 dealing with CPU detection
- One MAINTAINERS update"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: always enable USB VBUS regulators
ARM: davinci: nand: specify ecc strength
ARM: OMAP: rx51: change musb mode to OTG
ARM: OMAP2: fix musb usage for n8x0
MAINTAINERS: Update email address for Benoit Cousson
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: SAMSUNG: fix to support for missing cpu specific map_io
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
'gpmc_irq_start' is mostly used as 'int', and for a variable, do not
suggest to only use 'unsigned' as its type, so use 'int' instead of
'unsigned' for variable 'gpmc_irq_start'.
Also it will fix the related issue (dummy the real world failure):
arch/arm/mach-omap2/gpmc.c:728:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The denominator should be load from INCREMENTOR_DENUMERATOR_RELOAD_OFFSET
rather than INCREMENTER_NUMERATOR_OFFSET.
This is more likely a typo, since INCREMENTER_DENUMERATOR_RELOAD[23:17] is
reserved. It seems that it won't make much trouble without this fix, because
the useful [11:0] bits are mask and set the right value. Anyway, reading
from a right address is better choice.
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the cold reset was triggered. It happened due to oposite offsets
of cold/warm flags in PRM_RSTST and PRM_RSTCTRL registers.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM and DMIC only available on OMAP4/5 which no longer boots in legacy
mode.
The code to create the devices in legacy mode can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwmod data for the mailbox IP in OMAP5 SoC.
This is needed to be able to enable the OMAP mailbox
support for OMAP5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Tony Lindgren:
USB nop phy rename via Felipe Balbi <balbi@ti.com>:
Here's a pull request of one patch to avoid conflicts during the merge
window.
* tag 'omap-for-v3.12/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Peripheral-only mode got broken in v3.11-rc1 because of unknown reasons.
Change the mode to OTG, in practice that should work equally well even
when/if the regression gets fixed.
Note that the peripheral-only regression is a separate patch, this change
is still correct as the role is handled by hardware.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit b7e2e75a8c ("usb: gadget: drop unused USB_GADGET_MUSB_HDRC")
dropped a config symbol that was unused by the musb core, but it turns
out that board support code still had references to it.
As the core now handles both dual role and host-only modes, we can just
pass MUSB_OTG as mode from board files.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The soc_ops for dra7xx devices can be completed reused
from the ones used for omap4 and omap5 devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
All of OMAP5 timer support for clocksource and clockevent is completely
reused across DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The IO descriptor tables for DRA7 are a complete reuse from OMAP5.
A new dra7xx_init_early() does the base address inits.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The PRCM and MPUSS parts of DRA7 devices are quite identical
to OMAP5 so as to reuse all the existing infrastructure around it.
Makefile updates to do just that.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
From Tony Lindgren:
Removal of unused omap defines via Paul Walmsley <paul@pwsan.com>:
This series removes the currently-unused PRCM macros from
arch/arm/mach-omap2.
Basic test logs are available at:
http://www.pwsan.com/omap/testlogs/drop_unused_prcm_macros_v3.11-rc/20130721211401/
Once, years ago, we thought that it would be good to document the PRCM
register bits in the Linux codebase. Most folks in the broader
community did not have access to the same documentation, so we thought
that they might be able to use these bits to fix bugs and improve the
code.
We were also able to autogenerate most of these macros, so it was
thought that defining them in advance would reduce the risk of error,
inconsistencies, and merge conflicts caused when patch sets
incrementally defined them by hand.
Well, nice thoughts. But the first rationale was rendered partially
obsolete when TI started to release public TRM documentation PDFs at
some point in the OMAP3 timeframe. (Despite their weaknesses, TI's
public OMAP TRMs remain the most useful public documentation available
for any ARM Linux SoC -- at least to the extent of my knowledge.) And
then the current Linux development tropism towards
development-by-negative-diffstat obliterated the remainder of the
above two philosophies.
So, for the few, the masochistic, out there who wish to continue
developing TI PRCM code, I would ask that you resurrect any
additionally-needed macros from these commits, rather than writing
them manually. Purely for the sake of a pleasant atavism, perhaps; the
way one appreciates a used bookstore, or a video rental store...
And thanks to the upstream maintainers for being patient while we
adjust.
* tag 'omap-for-v3.12/cleanup-unused-defines' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP5: PRM/CM: Cleanup unused header
ARM: OMAP4: PRM/CM: Cleanup unused header
ARM: OMAP3: PRM/CM: Cleanup unused header
ARM: OMAP2: PRM/CM: Cleanup unused header
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The omap_init_rng() routine in devices.c only needs to be
called when there is no device tree present.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A recent patch ef3160c (ARM: OMAP2+: Divorce from local timer API,
2013-03-04) broke the omap build when SMP=n because the TWD functions
are only compiled on SMP=y builds. Stub out the TWD calls when the TWD
isn't built in to to keep everything building.
arch/arm/mach-omap2/built-in.o: In function `omap4_local_timer_init':
dss-common.c:(.init.text+0x1d90): undefined reference to `twd_local_timer_register'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Panda's DVI connector's DDC pins are connected to OMAP's third i2c bus.
With non-DT, the bus number was 3, and that is what is used in the
dss-common.c which contains the platform data for Panda's DVI.
However, with DT, the bus number is 2. As we now only have DT boot for
Panda, we have to change the bus number to make DVI EDID read
operational.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Register target address to be used for cpgmac is the second device
address space. By default, hwmod picks first address space (0th index)
for register target.
With removal of address space from hwmod and using DT instead, cpgmac
is getting wrong address space for register target.
Fix it by indicating the address space to be used for register target.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.
Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled
state post setup(). When a omap_device gets created for such hwmods
make sure the omap_device and pm_runtime states are also in sync for such
hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the
device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with
HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup.
Even if they have drivers missing, avoid idling them as part of
omap_device_late_idle()
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
prm-regbits-54xx.h was found to be completely unused and
hence removed.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Till the OMAP clocks are correctly defined in device tree, use
this temporary hack to provide clock alias to the USB PHY clocks.
Without this, USB Host & Ethernet will not be functional with
device tree boots on Panda and uEVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"ARM: OMAP: build mach-omap code only if needed" moved around the
ARCH_OMAP2PLUS stanza, but accidentally dropped the seleciton of
TI_PRIV_EDMA in the process. Add it back.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Some OMAP SoCs use this function while others do not, and that
causes a warning when building multi_v7_defconfig. Marking the
function __maybe_unused silences the harmless warning without the
need to add complex #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
If we build a kernel with CONFIG_ARCH_OMAP2PLUS enabled but all of the
individual SoCs disabled, we run into a large number of link errors
because if incorrect dependencies:
arch/arm/mach-omap2/built-in.o: In function `_add_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:691: undefined reference to `clkdm_add_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_del_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:720: undefined reference to `clkdm_del_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_enable':
arch/arm/mach-omap2/omap_hwmod.c:2145: undefined reference to `clkdm_in_hwsup'
arch/arm/mach-omap2/omap_hwmod.c:2147: undefined reference to `clkdm_hwmod_enable'
arch/arm/mach-omap2/omap_hwmod.c:2191: undefined reference to `clkdm_hwmod_disable'
arch/arm/mach-omap2/omap_hwmod.c:2146: undefined reference to `clkdm_missing_idle_reporting' arch/arm/mach-omap2/built-in.o: In function `_idle':
arch/arm/mach-omap2/omap_hwmod.c:2235: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `_shutdown':
arch/arm/mach-omap2/omap_hwmod.c:2338: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `omap_hwmod_get_context_loss_count':
arch/arm/mach-omap2/omap_hwmod.c:4071: undefined reference to `pwrdm_get_context_loss_count' arch/arm/mach-omap2/built-in.o: In function `omap_pm_clkdms_setup':
arch/arm/mach-omap2/pm.c:114: undefined reference to `clkdm_allow_idle'
arch/arm/mach-omap2/pm.c:117: undefined reference to `clkdm_sleep' arch/arm/mach-omap2/built-in.o: In function `omap2_common_pm_late_init':
arch/arm/mach-omap2/pm.c:294: undefined reference to `omap_voltage_late_init' arch/arm/mach-omap2/built-in.o: In function `omap2_gpio_dev_init':
arch/arm/mach-omap2/gpio.c:133: undefined reference to `pwrdm_can_ever_lose_context'
We can avoid this if we make CONFIG_ARCH_OMAP2PLUS a silent option that
gets enabled any time that one of the SoC versions is enabled.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are selected by omap4 but used in common omap4/5
SMP code, so building an omap5-only kernel is actually
broken without this patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
