Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9d ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add device tree nodes for pin pull-up/pull-down
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
* tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
Signed-off-by: Olof Johansson <olof@lixom.net>
The mmc controller in da850 supports high speed modes
so add cap-sd-highspeed and cap-mmc-highspeed.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
This SoC has a separate pin controller for configuring pullup/pulldown
bias on groups of pins.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Pull "omap dts changes for v4.10, part 2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.10 merge window:
- Fix up new instances of gpio-key,wakeup to use wakeup-source
- Add beaglebone LCDC blue-and-red-wiring property to make use
of the new driver features
- Add bindings for IIO support for am335x and am437x
- Add palmas PMIC overide powerhold property for am57xx
- Update am335x-baltos to use phy-handle property
- Add initial support for am571x-idk
* tag 'omap-for-v4.10/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: AM571x-IDK Initial Support
ARM: dts: am335x-baltos: use phy-phandle declarations
ARM: dts: am57xx-idk-common: Add overide powerhold property
ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property
ARM: dts: am57xx-idk: Add Industrial output support
ARM: dts: am57xx-idk: Add Industrial input support
ARM: dts: am437x-idk: Add Industrial output support
ARM: dts: am437x-idk: Add Industrial input support
ARM: dts: am335x-icev2: Add ADC support
ARM: dts: am335x-icev2: Disable Industrial I/O LEDs and fix naming
ARM: dts: am335x-icev2: Add Industrial input support
ARM: dts: am335x-boneblack: Add blue-and-red-wiring -property to LCDC node
ARM: dts: omap5: replace gpio-key,wakeup with wakeup-source property
Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:
Add Turris Omnia support, an open hardware router Armada 385 based
* tag 'mvebu-dt-4.10-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
Pull "Rockchip dts32 changes for 4.10" from Heiko Stübner:
A bit of attention for the rk3066, fixed tsadc reset node
as well as enabling the dma for uart and mmc controllers.
And one new soc, the rk1108 combining a single-core Cortex-A7
with a separate DSP core.
* tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the sdmmc pinctrl for rk1108
ARM: dts: rockchip: add rockchip RK1108 Evaluation board
ARM: dts: rockchip: add basic support for RK1108 SOC
clk: rockchip: add dt-binding header for rk1108
dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
ARM: dts: rockchip: enable dma for uart and mmc on rk3066a
ARM: dts: rockchip: fix TSADC reset node for rk3066a
Pull "Qualcomm Device Tree Changes for v4.10 - Part 2" from Andy Gross:
* Add SDHC xo clk
* tag 'qcom-dts-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: Add xo to sdhc clock node on qcom platforms
Pull "Samsung DeviceTree second update for v4.10" from Krzysztof Kozłowski:
1. Cleanups in MSHC nodes.
2. Enable ADC on Odroid boards.
3. Fix interrupt flags on recently added DMA sound nodes in Exynos5410.
* tag 'samsung-dt-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove the cd-gpios property for eMMC of Odroid XU3/4
ARM: dts: exynos: Specify snps, dwmac in compatible string for gmac
ARM: dts: exynos: Fix invalid GIC interrupt flags in audio block of Exynos5410
ARM: dts: exynos: Add ADCs on 4412 and 5422 based odroid boards.
ARM: dts: exynos: Replace "clock-freq-min-max" with "max-frequency"
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
Merge "SoCFPGA DTS update for v4.10, part 3" from Dinh Nguyen:
- Fine tune L2 cache configuration
* tag 'socfpga_dts_for_v4.10_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: fine-tune L2 cache configuration
Pull "DaVinci DT updates for v4.10 (part 3)" from Sekhar Nori:
Some fixes for device-tree patches already queued.
- Fix SD card detect polarity
- Prevent Ethernet from picking a random mac address
- Fix error messages on platforms which dont use
bus master and emif priority settings.
* tag 'davinci-for-v4.10/dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: da850-lcdk: fix mmc card detect polarity
Pull "DaVinci DT updates for v4.10 (part 2)" from Sekhar Nori:
Adds device tree nodes enabling DDR controller
and bus master priority settings needed for
stable LCDC operation on DA850.
Also adds support for MUSB device on DA850
providing USB OTG support.
* tag 'davinci-for-v4.10/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Enable the usb otg device node
ARM: dts: da850: Add the usb otg device node
ARM: dts: da850: add the mstpri and ddrctl nodes
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.
Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Pull "This device-tree pxa update brings" from Robert Jarzmik:
- pxa25x support
- cpu operating points in preparation for cpufreq-dt
- small fixes
* tag 'pxa-dt-4.10' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: add pxa27x cpu operating points
ARM: dts: pxa: add pxa25x cpu operating points
ARM: dts: pxa: fix gpio0 and gpio1 interrupts
ARM: dts: pxa: fix no. of gpio cells in the pxa gpio binding documentation
ARM: dts: pxa: add pxa25x .dtsi file
Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Pull "ARM: OXNAS SoC DT updates for 4.10" from Neil Armstrong:
- Add DTSI for Oxford Semiconductor OX820
- Add DTS for Cloud Engines PogoPlug v3 board
- Fix MAINTAINERS Oxnas entry for dts files
from http://lkml.kernel.org/r/20161102141850.25164-1-narmstrong@baylibre.com
* tag 'oxnas-arm-soc-dt-for-4.10' of https://github.com/OXNAS/linux:
MAINTAINERS: oxnas: Add new files definitions
ARM: dts: Add support for OX820 and Pogoplug V3
Pull "STi DT fix" from Patrice Chotard:
The I2C nodes are missing #address-cells and #size-cells.
This is causing warning at device tree compilation when
some I2C device sub-nodes are defined.
* tag 'sti-dt-for-v4.9-rc-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: fix i2c nodes
Pull "Allwinner fixes for 4.9, second iteration" from Maxime Ripard:
A renaming of the GR8 DTSI and DTS to make it explicitly part of the sun5i
family.
* tag 'sunxi-fixes-for-4.9-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: gr8: Rename the DTSI and relevant DTS
This patch fixes the following DTC warnings with W=1:
Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@4 has a unit
name, but no reg property
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
