tsin2 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin1 channel can be configured for either serial or parallel data
transfer. This patch adds the pinctrl config for both possibilities.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsin0 and be configured as either serial or parallel. This patch
adds the pinctrl config for both possiblities. On B2120 reference
design tsin0 is brought out as TSA on the NIMA slot of the B2004A
daughter board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
tsadc-tshut-mode and tsadc-tshut-polarity properties don't exist. The rockchip
thermal driver looks for rockchip,hw-tshut-mode and rockchip,hw-tshut-polarity
instead, otherwise it might freeze or hang the device according to the default
mode or polarity used.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge "Samsung fixes for v4.2" from Kukjin Kim:
From Krzysztof Kozlowski:
1. Fix exynos3250 MIPI DSI display and MIPI CSIS-2 camera sensorx
after adding support for PMU regmap in exynos-video-mipi driver
(issue introduced in v4.0).
2. Bring back cpufreq for exynos4210 after incomplete switch to
cpufreq-dt driver in 4.2 merge window. The necessary DT changes
for exynos4210 cpufreq was not applied to the same tree as rest
of patchset because of multiple conflicts between clk and arm-soc
trees. Unfortunately without the change the exynos4210 boards
loose cpufreq feature.
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
The Terasic DE0 Atlas board is also known as the DE0-Nano board.
This patch adds the DTS board file for the DE0-Nano Sockit board, and not
the DE0 Nano "Development Board".
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Updated skew settings for the gmac1 node as this board is using the
KSZ9031 PHY instead of the 9021 PHY.
v2: use stdpath-out for console and remove comment regarding u-boot ethaddr
Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds missing bits for EHCI HS USB host support and 32k clock
buffer control for the wg7210 bt+wifi module.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- add pandora specific compatible name
- fix mmc2 card detect polarity
- fix mmc1 and mmc2 write protect polarity
- disable write protect pins because of production issue and add an
explanation why they are disabled
- fix NAND partition name to reflect the correct address
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Palmas on OMAP5uevm has support for power button, so enable it.
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add serialN aliases for all 6 UART instances on
the AM437x SoC so each board's .dts file does not
have to define its own aliases.
Remove the alias added for am437x-gp-evm.dts now
that we have the aliases defined in am4372.dtsi
file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.
Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.
WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phyCORE-AM335x is a SoM (System on Module) containing
a AM335x SOC. The module can be connected to different
carrier boards.
Some hardware parts are configurable on the phyCORE-AM335x.
So they are disabled on default in this som dtsi file.
They will be enabled in the board dts files, when populated.
* RAM up to 1GiB
* PMIC
* NAND flash up to 1GiB
* Eth PHY on SOM: 1x RMII
* SPI NOR flash 8MiB (optional)
* i2c RTC (optional)
* i2c EEPROM 4kiB (optional)
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In tsc2046 touch driver, the values such as ti,x-min is defined as a u16
value. the driver use API of_property_read_u16() read the value. For these
u16 value, the dts entry should be like:
property = /bits/ 16 <0x5000>;
This describes the property as a u16 value.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previously defined Device Tree node, can be extended either by defining
a node using the same full path or by creating a label for the node and
referencing to it.
Using full paths is more error prone since if there was a typo error, a
new node will be created instead of extending the node as it was desired.
This will lead to run-time errors that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error which
makes it easier to detect the mistake since happens at build-time instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The dtc compiler combines all the defined nodes that have the same path
so a device node definition can be in one file and later be extended in
another one.
That's the case of the Exynos5420 pinctrl device nodes that are defined
in the exynos5420.dtsi file and extended in exynos5420-pinctrl.dtsi.
But since the exynos5420.dtsi file includes the exynos5420-pinctrl.dtsi
before the pinctrl device nodes are actually defined, the definition of
the pinctrl device nodes happens in exynos5420-pinctrl.dtsi and are
extended in exynos5420.dtsi.
That is the opposite of the original intention so even when there is no
difference in practice, the exynos5420-pinctrl.dtsi include should be
moved at the end of the exynos5420.dtsi file after the pinctrl device
nodes have been already defined.
This will also allow to later change the exynos5420-pinctrl.dtsi file
to use labels instead of full paths to extend the pinctrl nodes. Since
keeping the include at the top, would cause a dtc build error due the
pinctrl labels not being defined yet.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
A previously defined Device Tree node, can be extended either by defining
a node using the same full path or by creating a label for the node and
referencing to it.
Using full paths is more error prone since if there was a typo error, a
new node will be created instead of extending the node as it was desired.
This will lead to run-time errors that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error which
makes it easier to detect the mistake since happens at build-time instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The dtc compiler combines all the defined nodes that have the same path
so a device node definition can be in one file and later be extended in
another one.
That's the case of the Exynos5250 pinctrl device nodes that are defined
in the exynos5250.dtsi file and extended in exynos5250-pinctrl.dtsi.
But since the exynos5250.dtsi file includes the exynos5250-pinctrl.dtsi
before the pinctrl device nodes are actually defined, the definition of
the pinctrl device nodes happens in exynos5250-pinctrl.dtsi and are
extended in exynos5250.dtsi.
That is the opposite of the original intention so even when there is no
difference in practice, the exynos5250-pinctrl.dtsi include should be
moved at the end of the exynos5250.dtsi file after the pinctrl device
nodes have been already defined.
This will also allow to later change the exynos5250-pinctrl.dtsi file
to use labels instead of full paths to extend the pinctrl nodes. Since
keeping the include at the top, would cause a dtc build error due the
pinctrl labels not being defined yet.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add some safe values for over heat and over voltage. The Trats2 uses
3.8 V battery and during testing it operated properly under 4.48 V.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enable regulator for usbdrd3_0 and usbdrd3_1. Looking at the schematic
pin diagram for MAX77802 USB3_0 and USB3_1 is regulated by LDO9 and
LD011.
This removes following warnings during boot:
[ 3.503539] exynos-dwc3 usb@12000000: Looking up vdd33-supply from device tree
[ 3.503556] exynos-dwc3 usb@12000000: Looking up vdd33-supply property in node /usb@12000000 failed
[ 3.503568] usb@12000000 supply vdd33 not found, using dummy regulator
[ 3.509154] exynos-dwc3 usb@12000000: Looking up vdd10-supply from device tree
[ 3.509170] exynos-dwc3 usb@12000000: Looking up vdd10-supply property in node /usb@12000000 failed
[ 3.509181] usb@12000000 supply vdd10 not found, using dummy regulator
[ 3.917548] exynos-dwc3 usb@12400000: Looking up vdd33-supply from device tree
[ 3.917565] exynos-dwc3 usb@12400000: Looking up vdd33-supply property in node /usb@12400000 failed
[ 3.917578] usb@12400000 supply vdd33 not found, using dummy regulator
[ 3.922731] exynos-dwc3 usb@12400000: Looking up vdd10-supply from device tree
[ 3.922747] exynos-dwc3 usb@12400000: Looking up vdd10-supply property in node /usb@12400000 failed
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The UART status properties are indented one level too deep, and we want
to derive a device tree for the ODROID-XU. Fix this before it propagates.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
After the commit abc0b1447d ("drm: Perform basic sanity checks on
probed modes"), proper clock-frequency becomes mandatory for
validating the mode of panel. The display does not work if there is
no mode validated. Also, this clock-frequency must be set
appropriately for getting required frame rate.
Fixes: abc0b1447d ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Sigend-off-by: Kukjin Kim <kgene@kernel.org>
As a follow-up to recent changes to Exynos mipi video phy driver,
introducing support for PMU regmap in commit e4b3d38088 ("phy:
exynos-video-mipi: Fix regression by adding support for PMU regmap")
add a syscon phandle to video-phy node to bring back to life both
MIPI DSI display and MIPI CSIS-2 camera sensor on Exynos3250.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Just in case the firmware did not enable data and instruction prefetch in
the L2 cache controller, we enable it in the kernel.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG algorithms.
It could be found on many Allwinner SoC.
This patch enable the Security System on the Allwinner A20 SoC Device-tree.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Security System is a hardware cryptographic accelerator that support
AES/MD5/SHA1/DES/3DES/PRNG algorithms.
It could be found on many Allwinner SoC.
This patch enable the Security System on the Allwinner A10 SoC Device-tree.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
We used to provide dummy clocks for the UART. Now that we have
common clock support we can provide the real clocks to the UART.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8135 eval board contains a MT6397 PMIC. This adds the
corresponding device node to the dts file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the pmic wrapper node to the MediaTek MT8135 dtsi file.
This unit is used to access the PMIC on MediaTek boards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Merge "Rockchip dts changes for 4.3, part1" from Heiko Stuebner:
This adds the board for the Netxeon R89 used in different TV-boxes and
the initial support for two Chromebooks from the veyron family.
Additionally a non-critical fix for the watchdog irq on rk3288, addition
of the gmac reset line, a ramp delay for the cpu regulator on the firefly
board and cpu affinity for the arm-pmu spi irqs.
* tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288 arm-pmu irq affinity
dt-bindings: document rk3368 R88 board from Rockchip
ARM: dts: rockchip: add missing device_type = "memory" to boards
ARM: dts: rockchip: add veyron-pinky board
ARM: dts: rockchip: add veyron-jerry board
ARM: dts: rockchip: add shared rk3288-veyron files
ARM: dts: Add sbs-battery dts fragment used by chromebooks
ARM: dts: rockchip: add Netxeon R89 board
dt-bindings: add vendor prefix for Netxeon Technology
ARM: dts: rockchip: fix rk3288 watchdog irq
ARM: dts: rockchip: Add ramp delay for vdd_cpu in firefly board dts
ARM: dts: rockchip: Add STMMAC reset signal in GMAC interface for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Broadcom Device Tree changes for 4.3 (part 1)" from Florian Fainelli:
This pull request contains two changes:
- Ray adds the relevant clocks device tree nodes for Cygnus SoCs
- Rafal enables UART0 on BCM5301X routers where it has been verified to work
correctly
* tag 'arm-soc/for-4.3/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Enable UART0 on tested devices
ARM: dts: enable clock support for Broadcom Cygnus
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: Couple of dts fixes for v4.2-rcx" from Santosh Shilimkar:
Couple of DTS fixes 4.2-rcx for Keystone EVMs:
K2E EVM boot hangs because of missing serdes driver which is needed to bring up
PCIe on K2E. These couple of fixes makes the PCIE disabled on common default and
let the specific board DTS to enable it.
* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
Signed-off-by: Olof Johansson <olof@lixom.net>
