ARM: tegra: Devicetree changes for v4.3-rc1
Enables CPU frequency scaling on Jetson TK1 and enables the GK20A GPU on
Venice2 and Jetson TK1. This also enables support for the PMU hardware
found on Tegra124, which among other things, can be used for performance
measurements.
* tag 'tegra-for-4.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
pinctrl: tegra: Only set the gpio range if needed
clk: tegra: Add the DFLL as a possible parent of the cclk_g clock
clk: tegra: Save/restore CCLKG_BURST_POLICY on suspend
clk: tegra: Add Tegra124 DFLL clocksource platform driver
clk: tegra: Add DFLL DVCO reset control for Tegra124
clk: tegra: Introduce ability for SoC-specific reset control callbacks
clk: tegra: Add functions for parsing CVB tables
clk: tegra: Add closed loop support for the DFLL
clk: tegra: Add library for the DFLL clock source (open-loop mode)
clk: tegra: Add binding for the Tegra124 DFLL clocksource
Signed-off-by: Olof Johansson <olof@lixom.net>
Current base address is wrong by 0x04 bytes for AHB bus device as shown
in dmesg:
tegra-ahb 6000c004.ahb: incorrect AHB base address in DT data - enabling workaround
To correct old DTBs, commit ce7a10b0ff ("ARM: 8334/1: amba: tegra-ahb:
detect and correct bogus base address") checks for the low bit of the
base address and removes theses 0x04 bytes at runtime.
This patch fixes the original DTS, so upstream version doesn't need the
workaround of the base address.
As both addresses are valid, this patch doesn't break compatibility.
Tested on tegra20-paz00 (aka ac100).
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch modifies the device tree for Tegra124 based devices to enable
the Cortex A15 PMU. The interrupt numbers are taken from NVIDIA Tegra K1
TRM (DP-06905-001_v03p). This patch was tested on a Jetson TK1.
Signed-off-by: Kyle Huey <khuey@kylehuey.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device-tree node for the GK20A GPU and leave it disabled.
It is the responsibility of the bootloader to enable it if the
VPR registers have been programmed such that the GPU can operate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Nouveau can make use of the IOMMU to make physical appear linear in the
GPU address space.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra124 cpufreq driver relies on certain clocks being present
in the /cpus/cpu@0 node.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the board-specific properties of the DFLL for the Jetson TK1 board.
On this board, the DFLL will take control of the sd0 regulator on the
on-board AS3722 PMIC.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DFLL clocksource is a separate IP block from the usual
clock-and-reset controller, so it gets its own device tree node.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Samsung 2nd DT updates for v4.3
- for exynos3250, 4212, 4412 and 5250
: add CPU OPP and regulator supply property
- for exynos3250
: add CPU cooling binding for exynos3250 boards
- for exynos4 SoCs
: add iommu property to JPEG device
- for exynos4412-odroidu3
: enable SPI1
- for exynos5250-snow
: add SPI CS
- for exynos5422
: add exynos5422-cpus.dtsi to correct cpu order
* Note this branch is depending on tags/samsung-clk-driver
* tag 'samsung-late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
ARM: dts: Add SPI CS on exynos5250-snow
ARM: dts: Add CPU cooling binding for exynos3250 boards
ARM: dts: add exynos5422-cpus.dtsi to correct cpu order
ARM: dts: add CPU OPP and regulator supply property for exynos4x12
ARM: dts: Add CPU OPP and regulator supply property for exynos3250
ARM: dts: add CPU OPP and regulator supply property for exynos5250
ARM: dts: Extend exynos5420-pinctrl nodes using labels instead of paths
ARM: dts: Include exynos5420-pinctrl after the nodes were defined for exynos5420
ARM: dts: Extend exynos5250-pinctrl nodes using labels instead of paths
ARM: dts: Include exynos5250-pinctrl after the nodes were defined for exynos5250
ARM: dts: Enable thermal-zones for exynos5422-odroidxu3
ARM: dts: Define default thermal-zones for exynos5422
ARM: dts: Enable TMU for exynos5422-odroidxu3
ARM: dts: Add pwm-fan node for exynos5422-odroidxu3
ARM: dts: Use labels for overriding nodes for exynos4210-universal_c210
ARM: dts: Set max17047 over heat and voltage thresholds for exynos4412-trats2
ARM: dts: Enable USB3 regulators for exynos5422-odroidxu3
ARM: dts: Clean up indentation for exynos5410-smdk5410
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This SoC is integrated with 4 Cortex-A9 cores. The GIC bindings
document says that the bits[15:8] of the 3rd cell of the interrupts
property represents PPI interrupt CPU mask. Because the timer
interrupts are wired to all of the 4 cores, bits[15:8] should be set
to 0xf.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When getting translated from a downstream device tree that used slightly
different DT bindings, these regulators got labeled with the
"on-in-suspend" state, when they were actually supposed to be turned off
for S3 suspend. This was harmless, but not intentional, AFAICT.
Let's turn them off to get the optimal power state.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This DTS file was submitted with non-upstream bindings. I happened
across this while reviewing the jaq DTS.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix up bogus RTC compatible change for am4372 and add missing
DPLL for am4372 cpsw Ethernet driver. Also add ARM global and
local timers for am4372.
* tag 'omap-for-v4.3/dt-pt4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: dts: am4372: Set the default clock rate for dpll_clksel_mac_clk clock
ARM: dts: AM437X: add dpll_clksel_mac_clk node
Signed-off-by: Olof Johansson <olof@lixom.net>
The sp810 clk driver is calling the clk consumer APIs from
clk_prepare ops to change the parent to a 1 MHz fixed rate clock
for each of the clocks that the driver provides. Use
assigned-clock-parents for this instead of doing it in the driver
to avoid using the consumer API in provider code. This also
allows us to remove the usage of clk provider APIs that take a
struct clk as an argument from the sp810 driver.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX device tree updates for 4.3:
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
* tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: dts: imx6ul: add snvs power key support
ARM: dts: imx6ul: add RTC support
ARM: dts: imx6ul: enable GPC as extended interrupt controller
ARM: dts: imx6sx: correct property name for wakeup source
ARM: dts: add property for maximum ADC clock frequencies
ARM: dts: imx7d: enable snvs rtc, onoffkey and power off
ARM: dts: imx6ul-14x14-evk: add fec1 and fec2 support
ARM: dts: imx: add fec1 and fec2 nodes for SOC i.MX6UL
ARM: dts: imx27: add support of internal rtc
ARM: dts: vf-colibri: define stdout-path property
ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR
ARM: dts: ls1021a: Add the eTSEC controller nodes
ARM: dts: imx6ul: add qspi support
ARM: dts: imx6ul: fix low case define in imx6ul-pinfunc.h
ARM: dts: imx6ul: add usb host and function support
ARM: dts: vfxxx: Add io-channel-cells property for ADC node
ARM: dts: ls1021a: Add dts nodes for audio on LS1021A
ARM: imx6qdl-sabreauto.dtsi: enable USB support
ARM: dts: imx: update snvs to use syscon access register
ARM: dts: imx: add imx6ul and imx6ul evk board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"A smallish batch of fixes, a little more than expected this late, but
all fixes are contained to their platforms and seem reasonably low
risk:
- a somewhat large SMP fix for ux500 that still seemed warranted to
include here
- OMAP DT fixes for pbias regulator specification that broke due to
some DT reshuffling
- PCIe IRQ routing bugfix for i.MX
- networking fixes for keystone
- runtime PM for OMAP GPMC
- a couple of error path bug fixes for exynos"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
memory: omap-gpmc: Don't try to save uninitialized GPMC context
ARM: imx6: correct i.MX6 PCIe interrupt routing
ARM: ux500: add an SMP enablement type and move cpu nodes
ARM: dts: dra7: Fix broken pbias device creation
ARM: dts: OMAP5: Fix broken pbias device creation
ARM: dts: OMAP4: Fix broken pbias device creation
ARM: dts: omap243x: Fix broken pbias device creation
ARM: EXYNOS: fix double of_node_put() on error path
ARM: EXYNOS: Fix potentian kfree() of ro memory
ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.
* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
Signed-off-by: Olof Johansson <olof@lixom.net>
CPSW driver has been updated with compatibles for enabling errata
workarounds. So updating cpsw compatibles.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver has been updated with compatibles for enabling errata
workarounds. So updating cpsw compatibles.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JPEG codec node has been added in parallel to the patch, which
added support for IOMMU to Exynos platform, so JPEG device for
Exynos4 SoCs lacked IOMMU property. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
SPI1 is available on IO Port #2 (as depicted on their website)
in PCB Revision 0.5 of Hardkernel Odroid U3 board.
The shield connects a 256KiB spi-nor flash on that bus.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Although there is only one choice of chipselect it is necessary to
specify it. The driver cannot claim the gpio otherwise.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The odroid-xu3 board which is based on exynos5422 not exynos5800
is booted from cortex-a7 core unlike exynos5800. The odroid-xu3's
cpu order is quite strange. cpu0 and cpu5-7 are cortex-a7 cores and
cpu1-4 are cortex-a15 cores. To correct this mis-odering, I added
exynos5422-cpus.dtsi and reversing cpu orders from exynos5420.
Now, cpu0-3 are cortex-a7 and cpu4-7 are cortex-a15.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanho Park <parkch98@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
For Exynos5250 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: split Exynos5250 support from the original patch]
[b.zolnierkie: added CPU regulator supply property for Spring boards]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Currently mdio bindings are defined in keystone.dtsi and this results
in incorrect unit address for the node on K2E and K2L SoCs. Fix this
by moving them to SoC specific DTS file.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently the MDIO clock is pointing to clkpa instead of clkcpgmac.
MDIO is part of the ethss and the clock should be clkcpgmac.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
- New Firmware node and accompanying binding document
* tag 'rpi-dt-for-armsoc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
dt/bindings: Add binding for the Raspberry Pi firmware driver
ARM: bcm2835: Add the firmware driver information to the RPi DT
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCFPGA DTS updates for v4.3, take 2
- Add DTS property "altr,modrst-offset" for reset driver to
use
- Add updated reset defines for the reset driver
- Add reset property for EMACs on Arria10
* tag 'socfpga_dts_for_v4.3_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Add resets for EMACs on Arria10
ARM: socfpga: dts: add "altr,modrst-offset" property
dt-bindings: Add reset manager offsets for Arria10
Signed-off-by: Olof Johansson <olof@lixom.net>
Some more devicetree changes, including usbphy support for the
Cortex-A9 SoCs and actually enabling usb on the rk3066-marsboard,
Two more veyron-devices - namely Speedy and Minnie and a fix for
the tsadc.
One slightly more interesting fix is the blocking of the last
16MB of memory on 4GB rk3288 devices. The rk3288 cannot use this
area for dma operations, so things like the mmc or usb controllers
regularly fail when trying to read data. This solution mimicks the
solution from the ChromeOS kernel, who also do not seem to have
found a better solution yet. Here it only moves to the devicetree.
As this issue is also present on the arm64 rk3368, any future
better solution to this problem would need to describe this in
the devicetree as well and could then remove this block.
* tag 'v4.3-rockchip32-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add veyron-minnie board
ARM: dts: rockchip: reserve unusable memory region on rk3288
ARM: dts: rockchip: enable usb controller on marsboard
ARM: dts: rockchip: add usb phys to Cortex-A9 socs
ARM: dts: rockchip: set correct dwc2 params for cortex-a9 socs
ARM: dts: rockchip: Add veyron-speedy board
ARM: dts: rockchip: Use correct dts properties for tsadc node on veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt changes for v4.3 (part #3)
- device tree part of the Dove PMU series
- converting a new orion5x based platform to dt: Linkstation Mini
* tag 'mvebu-dt-4.3-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: Convert Linkstation Mini to Device Tree
ARM: dt: dove: add GPU power domain description
ARM: dt: dove: add video decoder power domain description
ARM: dt: dove: wire up RTC interrupt
ARM: dt: Add PMU node, making PMU child devices childs of this node
Signed-off-by: Olof Johansson <olof@lixom.net>
Second batch of DT changes for 4.3:
- Add the slow clock to the nodes that will use it
- Add hlcd to the at91sam9x5 and at91sam9n12
- Add touchscreen and touch button support to the at91sam9x5ek
* tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (22 commits)
ARM: at91/dt: sama5d2: use slow clock where necessary
ARM: at91/dt: at91sam9x5dm: add QT1070 touch button controller
ARM: at91/dt: at91sam9x5dm: add support for the touschscreen
ARM: at91/dt: add drm support for at91sam9n12ek
ARM: at91/dt: enable lcd support for at91sam9x5 SoCs
ARM: at91/dt: add at91sam9x5-ek Display Module dtsi
ARM: at91/dt: include lcd dtsi in at91sam9x5 dtsis
ARM: at91/dt: define hlcdc node in at91sam9x5_lcd.dtsi
ARM: at91/dt: sama5d4: use slow clock where necessary
ARM: at91/dt: sama5d3: use slow clock where necessary
ARM: at91/dt: at91sam9x5: use slow clock where necessary
ARM: at91/dt: at91sam9rl: use slow clock where necessary
ARM: at91/dt: at91sam9n12: use slow clock where necessary
ARM: at91/dt: at91sam9g45: use slow clock where necessary
ARM: at91/dt: at91sam9263: use slow clock where necessary
ARM: at91/dt: at91sam9261: use slow clock where necessary
ARM: at91/dt: at91sam9260: use slow clock where necessary
ARM: at91/dt: at91rm9200: use slow clock where necessary
Documentation: dt: rtc: at91rm9200: add clocks property
Documentation: watchdog: at91sam9_wdt: add clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
AM437x devices sport SCU, TWD and Global timers,
let's add them to DTS so they have a chance to
probe and be used by Linux.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A31/A31s have the same "Security System" crypto engine as A10/A20,
but with a separate reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
am4372-rtc string was already part of dts, introduced to identify
the rtc specific to am4372 family of SoCs. It was removed in one of the
previous patches. Adding back the same with appropriate documentation.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrap the clock-indices to match the wrapping of the clock-output-names in
order to make it easier to match indices to names.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The A23 and A33 gates have a non continuous set of clock IDs that are
valid. Add the clock-indices property to the DT to express this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The A20 gates have a non continuous set of clock IDs that are valid. Add
the clock-indices property to the DT to express this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
