Add cap-sd-highspeed and cap-mmc-highspeed for rk3188-radxarock
board to make sd cards running faster.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pins for i2c5 can either be configured as "I2C5" which means that
they're controlled by the normal RK3288 I2C controller or as "EDP / HDMI
I2C". It's unclear why EDP is referenced here since apparently setting
the mux to this position enables I2C communication using the dw_hdmi
block with a patch like <https://patchwork.kernel.org/patch/7098101/>.
There appear to be some reasons why using the builtin I2C controller in
dw_hdmi is better than using the normal RK3288 I2C controller, so boards
based on rk3288 might eventually want to use this pinmux if it's known
to work.
Once driver support in dw_hdmi lands, boards would use this by selecting
this pinctrl for the HDMI block and then _not_ specifying a ddc-i2c-bus
and _not_ setting the status to "okay" for i2c5 (which uses the same
pins).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the previous patch ("rk3288: pull up cts lines") this is redundant,
I sent that patch for the same reason this existed here, so the lines don't
wiggle randomly when disconnected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The flow control lines from a user accessible UART are optional,
the user might not have anything connected to those pins.
In order to prevent random interrupts happening and noise affecting
the cts pin should be pulled up.
Note that the default state for that pin on the rk3288 is pulled up,
so this patch merely restores them.
This is similar to what we're already doing with the RX pin,
so it should be safe. At worst it might be a slightly higher power usage
(through ~50 kohms) when the cts is low.
Suggested-by: Neil Hendin <nhendin@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables SDMMC0 on the board and gives a basic support for SD cards.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge "ARM Keystone DTS updates" from Santosh Shilimkar:
- Add SOC compatible along with EVMs for future board variations.
- Add SPI nodes
* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Update SoC specific compatible flags
ARM: keystone: Update compatible to have SoC specific matches
Documentation: dt: keystone: provide SoC specific compatible flags
ARM: dts: keystone: Add ti,keystone-spi for SPI
Merge "Renesas ARM Based SoC DT Updates for v4.4" from Simon Horman:
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
* tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (28 commits)
ARM: shmobile: porter: add Ether DT support
ARM: shmobile: fix SILK board name
ARM: shmobile: r8a7794: add HS-USB DT support
ARM: shmobile: dts: Add common file for AA121TD01 panel
ARM: shmobile: r8a7794: link PCI USB devices to USB PHY
ARM: shmobile: silk: enable USB PHY
ARM: shmobile: r8a7794: add USB PHY DT support
ARM: shmobile: porter: initial device tree
ARM: shmobile: add Porter board DT bindings
ARM: shmobile: silk: enable internal PCI
ARM: shmobile: r8a7794: add internal PCI bridge nodes
ARM: shmobile: r8a7790: lager: add pinmux for iic0
ARM: shmobile: r8a7778: tidyup SSI resource region
ARM: shmobile: r8a7791: tidyup SSI resource region
ARM: shmobile: r8a7790: tidyup SSI resource region
ARM: shmobile: lager: use CCF for audio clock
ARM: shmobile: koelsch: use CCF for audio clock
ARM: shmobile: silk: add VIN0/ADV7180 DT support
ARM: shmobile: r8a7794: add VIN DT support
ARM: shmobile: silk: add I2C1 DT support
...
Enable SATA0 device for the Porter board.
This patch is analogous to the commit 5a62ec5700 ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Peach boards use the EC to store the vboot context information,
so add the corresponding properties on the EC node to indicate so.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Emilio Lopez <emilio.lopez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Device Tree improvements for Exynos based boards (updated pull request):
1. Enable DMA on Exynos4 serial ports. This old patch uncovered
a number of other issues in dmaengine and samsung serial driver.
All of known issues are resolved so finally enable the DMA for UART.
2. Fix incorrect location of display-timings node (FIMD->DP node)
on Arndale, SMDK5250 and SMDK5240 boards.
3. Minor cleanups.
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Define the Porter board dependent part of the SDHI0/2 device nodes along
with the necessary voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...
This patch is analogous to the commit 1299df03d7 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge "SoCFPGA DTS updates for v4.4" from Dinh Nguyen:
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
* tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: Add base stratix 10 dtsi
ARM: socfpga: dts: enable USB and I2C on Arria10 SoCDK
ARM: socfpga: dts: add clock fields for I2C, UART and USB on Arria10
Merge "First batch of DT changes for 4.4:" from Nicolas Ferre:
- some DT fixes: dma declaration, led labels
- disable some nodes: PMIC on sama5d3 Xplained, unused i2c1 on at91sam9n12ek
- add some others that were missing: touchscreen, cryto nodes, LCD panels or
image capture properties on various boards
- as the new pinmux for sama5d2 was accepted, we can now add the definitions
and the actual muxing for sama5d2 Xplained board
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: add device pin muxing
ARM: at91/dt: add sama5d2 pinmux
ARM: at91/dt: ov2640: add hsync/vsync-active property
ARM: at91/dt: sama5d4 xplained: enable the led D8
ARM: at91/dt: sama5d4ek: Add support of QT1070 and Maxtouch
ARM: at91/dt: sama5d4: enable crypto nodes
ARM: at91/dt: sama5d4: add pioD pin mux mask and enable pioD
ARM: at91/dt: sama5d3: update iio config for touchscreen
ARM: at91/dt: sama5d3 xplained: disable pmic
ARM: at91/dt: at91sam9x5: enable iio touchscreen for 9x5ek
ARM: at91/dt: at91sam9n12ek: disable i2c1
ARM: at91/dt: at91sam9n12ek: fix the led labels name
ARM: at91/dt: corrections to i2c1 declaration to sama5d4
Merge "efm32 cleanups for 4.4-rc1" from Uwe Kleine-Koenig:
These are just two followup cleanups for commits that are in v3.17-rc1 and
waited in my private tree for application since that time.
* tag 'efm32-for-4.4-rc1' of git://git.pengutronix.de/git/ukl/linux:
ARM: efm32: switch to vendor,device compatible strings
ARM: efm32: switch to properly namespaced location property
Merge "Renesas ARM Based SoC Fixes for v4.3" from Simon Horman
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
* tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
Merge "Allwinner fixes for 4.3" from Maxime Ripard:
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
* tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
Merge "Samsung fixes for v4.3" from Kukjin Kim:
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
On the Arria10 Devkit, the I2C bus has a serial EEPROM and an RTC
hanging off it. Also, enable the USB node.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the required clock fields for all the I2C nodes. Also add missing clock
fields for UART0 and USB1.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes but by not using a deprecated
property, new DTS based on this one will not carry the same issue.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch moves the display-timings node from fimd to dp to reflect the
device tree bindings change.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[tomeu.vizoso@collabora.com: Rebased]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Define the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
This patch is analogous to the commit 26b0d2cf73 ("ARM: shmobile:
henninger: add Ether DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This allows voltage-scaling with cpufreq-dt. The reliability of
voltage-scaling has been checked by reducing the voltage of all
operating points by 0.025V (for extra safety headroom) and running
libjpeg-turbo decoding tests on 5 pcDuino2 boards. It means that
the standard sun4i voltages should be perfectly fine too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which is a slightly modified version of the Henninger board).
SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently, BG2Q shares a compatible with BG2. This is incorrect, since
BG2 and BG2Q use different USB PLL dividers. In reality, BG2Q shares a
divider with BG2CD. Change BG2Q's USB PHY compatible string to reflect
that.
Cc: <stable@vger.kernel.org> # v4.2.0-
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
