In general, the sdio/sdmmc is used by the wifi module
and sd card.
let's add the node for these function.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs
can't set the status in the internal.
We should keep the default status for enable the gpio status,
In fact, the pull_none is the disable the gpio pull up/down.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add qspi memory mapped region entries for AM43xx based SoCs. Also,
update the binding documents for the controller to document this change.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add qspi memory mapped region entries for DRA7xx based SoCs. Also,
update the binding documents for the controller to document this change.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo")
because it It was already done and it's just a duplicate. See:
2d11961f3e ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
bluetooth HW is WLS1271 chip connected to UART1.
Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.
Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GSBI6 UART module is connected to BT chip, which uses
hardware flow control lines. Enable them on SoC side.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
Merge "SoCFPGA DTS update for v4.5" from Dinh Nguyen:
- Add DT board file for Denx MCVEVK board
* tag 'socfpga_dts_for_v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: Add support for DENX MCV SoM and MCVEVK baseboard
Merge "Realview DT files" from Linus Walleij:
The device tree changes for the continued RealView DT
support.
* tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add device tree for PB11MPCore
clk: add ARM syscon ICST device tree bindings
ARM: add DT bindings for the ARM11MPCore CPU cluster
Merge "Broadcom soc changes for v4.5" from Florian Fainelli:
This pull request contains Broadcom SoC changes for 4.5, with the following changes:
- Lucas Stach removes the workaround for an imprecise fault for Broadcom
BCM5301x SoCs (Northstar) since this is now handled by the ARM/Linux kernel
directly
- Hauke Merthens enables a bunch of erratas for the Cortex-A9 and PL310 L2
cache present on early Northstar chips (BCM4708)
- Kapil Hali adds SMP support for the Northstar Plus SoCs by consolidating the
existing SMP code for Kona SoCs (mobile platforms), fixng the Device Tree
binding for the Kona platforms (wrong placement for 'enable-method' and
'secondary-reg') and then finally adds the functional code for the Northstar
Plus platforms to boot their secondary CPUs
- Jon Mason enables SMP on BCM4708/BCM5301X (Northstar SoCs) by building the generic
Northstar/Northstar Plus SMP code, and adding the relevant SMP Device Tree nodes
* tag 'arm-soc/for-4.5/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
ARM: BCM5310X: activate erratas needed for SoC
ARM: BCM5301X: remove workaround imprecise abort fault handler
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
Though the driver will continue to check for and support the legacy
"isil,irq2-can-wakeup-machine" boolean property to wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "isil,irq2-can-wakeup-machine" with the
unified "wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add DT support for the Vivante GC600 GPU on Marvell Dove platforms.
These nodes default to being disabled unless a platform decides they
should be enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.
The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.
[gregory.clement@free-electrons.com: fix comment format]
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
A new compatible string has been introduced: atmel,sama5d4-i2c. It
allows to use the i2c-sda-hold-time-ns property if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the change of frequency a SAMA5D4 can reach, we have to modify the
maximum clock specification for the master clock, up to 200MHz now.
It avoids the wrong message saying that "master clk is overclocked" for this
configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
