Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.
While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.
A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.
This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file by
copying over reg_usb1_vbus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that the wifi chip is powered by both ldo3 and ldo4 tied
together and that using only one results in the wifi-chip dropping of
the USB bus sometimes.
Ideally we would have a proper way of modelling this (this is being
worked on), but currently we do not. This is not an issue since we need
to keep these regulators always-on anyways, due to these boards
crashing when ldo3/4 get turned back on after having been turned off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.
It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.
The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is used with the Allwinner A80 SoC, along with
an AXP806 PMIC as a slave.
This patch adds a dtsi file for all the common bindings and default
values unrelated to board design. Currently this is just listing all
the regulator nodes. The regulators are initialized based on their
device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Q8 form factor A13 tablets have a 7" LCD panel. Unfortunately we
don't know the exact model of the panel. Just pick a panel with
display timings close to what we know.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Q8 tablets use the audio codec to provide audio output via a
headphone jack or a small mono speaker. A GPIO output is used to
control speaker amp.
The tablets may or may not have an internal microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A13 Q8 tablets, the PMIC's USB power supply (VBUS) is connected
to the external OTG port. This can be used to provide power and OTG VBUS
sensing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The output pin of LDO is also a GPIO pin, and the on/off settings of the
regulator are actually pinmux settings.
Disable it by default so it doesn't conflict with GPIO usage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the display engine is shared between the R8 and the A13. Move the
common parts to the Á13 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The RGB bus can be used in several configurations, one of which being the
RGB666.
Add a pinctrl group for that case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Due to introducing the new driver - ACT8945A MFD drive,
change the pmic device node to align with the ACT8945A
regulator and charger drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the Advanced Power Management Units (APMU), and use
the enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC4 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a "serial1" alias for the serial console (it is labeled "uart1").
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC2 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC1 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC driver used to register itself as poweroff controller by
default, hence assuming that this device is using the PMIC as
system power controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes the following DTC warnings for am57xx-sbc-am57x.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-igep0050.dtb,
omap5-sbc-t54.dtb and omap5-uevm.dtb:
"connector@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-cm-t54.dtb:
"connector@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-sbc-t43.dtb:
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-gp-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am43xx-epos-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-var-dvk-om44.dtb
and omap4-var-stk-om44.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-sdp.dtb
and omap4-sdp-es23plus.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-panda.dtb,
omap4-panda-a4.dtb and omap4-panda-es.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"encoder@1 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-duovero-parlor.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-thunder.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-sbc-t3517.dtb,
omap3-sbc-t3530.dtb and omap3-sbc-t3730.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-pandora-600mhz.dtb
and omap3-pandora-1ghz.dtb:
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
