The DT compiler is now warning about unit names with addresses but not
reg property. Fix all the gpio-key buttons which causes warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Merge "ARM: mvebu: DT changes for v3.16" from Jason Cooper:
mvebu DT changes for v3.16
- kirkwood
- rework nsa3x0 board to add nsa320
- large cleanup to facilitate use in barebox
- guruplug phy updates
- audio updates for t5325
- mvebu
- use clocks vice clock-frequency for uart nodes
- armada 375/380/385
- add watchdog node
- add coherency fabric
- add smp support
- add sdhci
- add ahci
- add thermal sensor
- armada 370/XP
- and pmsu
* tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu: (35 commits)
ARM: Kirkwood: t5325: Use simple card to instantiate audio
ARM: Kirkwood: DT: Add missing #sound-dai-cells property
ARM: Kirkwood: Add node for audio codec
ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id
ARM: dts: kirkwood: set Guruplug ethernet PHY compatible
ARM: dts: kirkwood: set default pinctrl for I2C1 on 6282
ARM: dts: kirkwood: set default pinctrl for I2C0
ARM: dts: kirkwood: set default pinctrl for NAND
ARM: dts: kirkwood: set default pinctrl for SPI0
ARM: dts: kirkwood: set default pinctrl for UART0/1
ARM: dts: kirkwood: set default pinctrl for GBE1
ARM: dts: kirkwood: consolidate common pinctrl settings
ARM: dts: kirkwood: add pinctrl node to common SoC include
ARM: dts: kirkwood: rename pin-controller nodes
ARM: dts: kirkwood: remove clock-frequency properties from UART nodes
ARM: dts: kirkwood: add stdout-path property to all boards
ARM: dts: kirkwood: add node labels
ARM: mvebu: Enable the thermal sensor in Armada 380/385 SoC
ARM: mvebu: Enable the thermal sensor in Armada 375 SoC
ARM: mvebu: don't use clocks property in UART node for Netgear RN2120
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Most boards use the default UART0/1 pinctrl setting without RTS/CTS.
Add the pinctrl setting to the toplevel SoC UART nodes and put a note
in front of the corresponding pinctrl node to overwrite the setting
on board level. Currently, both boards using a different UART pinctrl
setting (Openblocks A6, A7) already overwrite the pinctrl node.
While at it, also fix up some status = "ok" to "okay" and again
whitespace issues on mplcec4 uart nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-10-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull devicetree updates from Rob Herring:
- Add new documents with guidelines for DT binding stability and review
process. This is one of the outcomes of Kernel Summit DT discussions
- Remove a bunch of device_type usage which is only for OF and
deprecated with FDT
- Fix a long standing issue with compatible string match ordering
- Various minor binding documentation updates
* tag 'devicetree-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: add rockchip vendor prefix
serial: vt8500: Add missing binding document for arch-vt8500 serial driver.
dt/bindings: submitting patches and ABI documents
DT: Add vendor prefix for Emerging Display Technologies
of: add vendor prefixe for EPFL
of: add vendor prefix for Gumstix
of: add vendor prefix for Ka-Ro electronics GmbH
devicetree: macb: Document clock properties
dts: bindings: trivial clock bindings doc fixes
of: Fix __of_device_is_available check
dt/bindings: Remove device_type "serial" from marvell,mv64360-mpsc
dt/bindings: remove device_type "network" references
dt/bindings: remove users of device_type "mdio"
dt/bindings: Remove references to linux,phandle properties
dt/bindings: Remove all references to device_type "ethernet-phy"
of: irq: Ignore disabled intc's when searching map
of: irq: Ignore disabled interrupt controllers
OF: base: match each node compatible against all given matches first
dt-bindings: add GIC-400 binding
The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.
This patch was generated mechanically with the following command and
then verified by looking at the diff.
sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Replace the numeric key value with a symbolic name from
<bt-bindings/input/input.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:
- The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.
- The A6 has one Ethernet port, while the A7 has two Ethernet ports
- The A6 has only one USB port, while the A7 integrates a USB hub,
which provides two front-side USB port, and an internal USB port as
well.
- The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.
- Slightly different GPIOs for some functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
